VGC VR-N7500 User manual

VR-N7500 Fast Operate Manual
Section I: How To Connect VR-N7500 With Cell-phone
Hand microphone status description:
Section II:How To Connect to Bluetooth Accessories?
Section III:How To Edit the frequency？
Section Ⅳ: Frequency display
1，For Android user
Scan the QR code to download the HT APP
or visit the website:
http://www.vgc.net.cn/download/22-en.html
For IOS user
Search 'BS HT' in APPLE store to download
2，Open the app, select-[BIND NEW DEVICE]. Turn-on the mobile radio, then press POWER key twice,
a 'BEEP' will be heard and red-green light flashing means the radio is now in pairing status
3，Select the scanned device then bind it
4，Some mobile phone Bluetooth pairing requires authorization, so check the phone menu,
select to confirm Bluetooth pairing can be paired successfully.
MUST
【M buttons】
Short press：Channel/Volume switch
Long press： Talk around function
Double press： Mute
【Up/Down button】 【PTT button】
Short press： Push to talk
Channel mode： Channel adjust
Volume mode： Volume adjust
【OK button】
Short press： Current channel prompts
1，Connect to Bluetooth PTT
Turn-on the mobile radio, then press【 POWER】 key twice, a 'BEEP' will be heard. Long press the
bluetooth PTT,
2，Connect to Bluetooth speaker mic
Turn-on the mobile radio, then press 【 POWER】 key twice, a 'BEEP' will be heard. Turn on the bluetooth
speaker mic, double press to enter pairing status.
red-green light flashing means the bluetooth PTT is now in pairing status
Turn on the APP,Long press the channel square,
then seclect【 Edit Channel】，When you edit the
completion channel parameters ,click 【 save】to
save the Channel Parameters.
When the frequency setting is completed, make the phone horizontally display, and the frequency will
be displayed on the map interface (the arrow up means TX and the arrow down means RX)

Section V：Create internet channel（For Android only）
Section Ⅵ：Bind network channel （For Android only）
Section Ⅶ：Turn on Network repeater function（For Android only）
Section Ⅷ：Turn off radio after pairing
Section Ⅸ：Turn on/off signal TONE
Section Ⅹ: Turn on audio relay
1，Turn on APP，select【join network channel】/【create a new channel】
2，Create channel name and password. Free to join if no password
3，Click 【SAVE】
1，Long press ID image, select Login , select 【Register】 to Register the account.
2，Select【join network channel】/【join existing channel】，click【magnifier】icon，type the channel
name to join in. Enter the password if need.
3，Long press on a channel square that you needed, select 【Bind network channel】, then select the
network channel you joined to bind
【 】
1. Under the network channel you are bound to, press and hold Relay Mode to realize network and
analog communucation. (Note: To achieve network-analog communication, you must have the
administrator qualification of the network group. If not, then no allow to operate)
2, 【Sync radio config】means 'synchronous radio configuration', this function can synchronize the analog
frequency of the network channel bound to the network channel into the same parameters
(with the consent of the members, please be cautious)
【 】
Open the app, click on the POWER button and turn it to gray to turn off the radio. The next time you
need to turn it on, open the app and click on 【POWER】 button again.
【 】
Long press the ID photo to enter the following interface:
Click 【Identification Information】to enable/disable
signaling, if 【Location】On, Signaling tone is coming
with position Signal
Open the APP, enter the frequency page, click setting icon , select General Settings ,
turn on 【Audio relay】 to implement the audio relay function (this function does not depend
on the network)
【 】

NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
ATTENTION: conditions of use!