Victor Tools C100 User manual

20V Pole One Handed
Cordless Saw
L249 v01: 26/10/22
Please read and retain these instructions for future reference
The Enterprise
Department
UK Head Office, 11 Bridge Street, Bishop’s Stortford, CM23 2JU
Tel: [phone]*, Fax: [phone]
www.coopersofstortford.co.uk
EU address: D.S.B. LD, 160 Bd. de Fourmies, 59100 Roubaix, France
Tel: [phone]
*UK Calls cost around 7 pence per minute plus your telephone company’s network access.
Please check with your telephone supplier.
Power Details: 100-240V AC, 50-60Hz
Accessories:
Use: This item requires one hand to use safely.
Please read this instruction manual thoroughly before starting and ensure you are familiar with the
operation of your new One Handed Cordless Saw.
RECOMMENDED FOR PERSONS OVER 18 YEARS OF AGE.
ALWAYS USE HEAD, EYE AND EAR PROTECTION EQUIPMENT AND SAFETY SHOES AND HAND GLOVES
Dimensions
(H) 17.6 x (W) 9 x (L) 33.8cm
Pole length: 125cm
•USE HANDHELD WITHOUT THE POLE EXTENSION OR
WITH FOR PRUNING BRANCHES ETC UP HIGH
•ITS LIGHTWEIGHT AT JUST 1kg WITHOUT THE POLE
AND WITH THE POLE 3kg MEANING YOU CAN USE IT
EASILY ONE HANDED
•WITH A 20V 1500MAH RECHARGEABLE BATTERY ITS
CABLE FREE SO YOU CAN USE IT ANYWHERE
•UPPER SAFETY GUARD, HAND GUARD AND LOCK OFF
SWITCH MEANS YOU CAN USE IT SAFELY WITHOUT
WORRY
•SOFT AND EASY GRIP HANDLE
•ADJUSTABLE TENSION
•USE FOR PRUNING, DEMOLITION, CUTTING
•NO LOAD SPEED- - 10M/S + 36000M/HOURS
•CHARGING TIME UP TO 180 MINS, USE TIME UP TO 40
MINUTES
•INCLUDES –1 X PRUNING TOOL, 1 X BATTERY PACK, 1 X
CHARGER, 1 X CHAIN, 1 X BAR, 1 X EXTENTION POLE, 1
X BLADE PROTECTION COVER
•SAW BLADE –4 INCHES
•MINIMUM CUTTING WIDTH –80MM

20V Pole One Handed Cordless Saw L249 Instructions for Use
Please read and retain these instructions for future reference v001: 26/10/22
The Enterprise
Department
UK Head Office, 11 Bridge Street, Bishop’s Stortford, CM23 2JU
Tel: [phone]*, Fax: [phone]
www.coopersofstortford.co.uk
EU address: D.S.B. LD, 160 Bd. de Fourmies, 59100 Roubaix, France
Tel: [phone]
*UK Calls cost around 7 pence per minute plus your telephone company’s network access.
Please check with your telephone supplier.
Parts

20V Pole One Handed Cordless Saw L249 Instructions for Use
Please read and retain these instructions for future reference v001: 26/10/22
The Enterprise
Department
UK Head Office, 11 Bridge Street, Bishop’s Stortford, CM23 2JU
Tel: [phone]*, Fax: [phone]
www.coopersofstortford.co.uk
EU address: D.S.B. LD, 160 Bd. de Fourmies, 59100 Roubaix, France
Tel: [phone]
*UK Calls cost around 7 pence per minute plus your telephone company’s network access.
Please check with your telephone supplier.
Operating Instruction
To remove the chain, loosen compression button remove the side cover anti-clock wise and remove the side
cover.
After loosening the pressure nut anti-clockwise,
remove the pressure cover (side cover).
After removing the side cover,
remove the guide plate directly as shown.
1. To remove the chain, loosen compression
button remove the side cover After removing the side
cover as pictured ‘remove the guide directly.
2. To install the chain guide plate: first load the chain
into the guide plate, and the middle guide tooth just
sticks into the guide plate guide slot.
Note: the chain blade should be forward.
Note: The cordless saw has a device to adjust the
tensioning of the chain. When installing the guide
plate, make sure that the adjusting block gets stuck
into the positioning adjusting hole at the end of the
guide plate.

20V Pole One Handed Cordless Saw L249 Instructions for Use
Please read and retain these instructions for future reference v001: 26/10/22
The Enterprise
Department
UK Head Office, 11 Bridge Street, Bishop’s Stortford, CM23 2JU
Tel: [phone]*, Fax: [phone]
www.coopersofstortford.co.uk
EU address: D.S.B. LD, 160 Bd. de Fourmies, 59100 Roubaix, France
Tel: [phone]
*UK Calls cost around 7 pence per minute plus your telephone company’s network access.
Please check with your telephone supplier.
Align the pin hole and install the reverse hole and chain

20V Pole One Handed Cordless Saw L249 Instructions for Use
Please read and retain these instructions for future reference v001: 26/10/22
The Enterprise
Department
UK Head Office, 11 Bridge Street, Bishop’s Stortford, CM23 2JU
Tel: [phone]*, Fax: [phone]
www.coopersofstortford.co.uk
EU address: D.S.B. LD, 160 Bd. de Fourmies, 59100 Roubaix, France
Tel: [phone]
*UK Calls cost around 7 pence per minute plus your telephone company’s network access.
Please check with your telephone supplier.
Install the side cover and tighten the screw nut
3. How to adjust the tightness of the chain?
The adjustment standard is to lift the chain in the
middle of the guide plate by hand and expose 1-3
middle guide teeth.
Loosen the compression nut.
As shown in the picture, twist the adjusting screw
clockwise to tighten the chain, anti-clockwise is for
loosening.

20V Pole One Handed Cordless Saw L249 Instructions for Use
Please read and retain these instructions for future reference v001: 26/10/22
The Enterprise
Department
UK Head Office, 11 Bridge Street, Bishop’s Stortford, CM23 2JU
Tel: [phone]*, Fax: [phone]
www.coopersofstortford.co.uk
EU address: D.S.B. LD, 160 Bd. de Fourmies, 59100 Roubaix, France
Tel: [phone]
*UK Calls cost around 7 pence per minute plus your telephone company’s network access.
Please check with your telephone supplier.
As shown in the picture, twist the adjusting screw
clockwise to tension the chain, anti-clockwise is
for loosening
The chain tightness is shown as below
Note: 1-3 middle guide teeth are exposed in the pull-down chain.
A new chain will be stretched in the early stages of use. Please check and adjust to the appropriate
tension frequently, because a loose chain will easily to derail, which may lead to rapid wear of the chain
and guide plate.
The chain must be stuck to the sprocket After installation, please check it again

20V Pole One Handed Cordless Saw L249 Instructions for Use
Please read and retain these instructions for future reference v001: 26/10/22
The Enterprise
Department
UK Head Office, 11 Bridge Street, Bishop’s Stortford, CM23 2JU
Tel: [phone]*, Fax: [phone]
www.coopersofstortford.co.uk
EU address: D.S.B. LD, 160 Bd. de Fourmies, 59100 Roubaix, France
Tel: [phone]
*UK Calls cost around 7 pence per minute plus your telephone company’s network access.
Please check with your telephone supplier.
Pull down the chain to expose the three middle guide teeth

20V Pole One Handed Cordless Saw L249 Instructions for Use
Please read and retain these instructions for future reference v001: 26/10/22
The Enterprise
Department
UK Head Office, 11 Bridge Street, Bishop’s Stortford, CM23 2JU
Tel: [phone]*, Fax: [phone]
www.coopersofstortford.co.uk
EU address: D.S.B. LD, 160 Bd. de Fourmies, 59100 Roubaix, France
Tel: [phone]
*UK Calls cost around 7 pence per minute plus your telephone company’s network access.
Please check with your telephone supplier.
CONTENTS
1) Cordless Saw
2) Battery
3) Charger
4) Instruction manual
•Do not expose the battery to extreme conditions such as high temperature or shock. Otherwise, it will
cause personal injury due to the leakage of the electrolytic solution.
•Before charging, check that the surface of the battery is clean and dry.
•The battery of this product is not fully charged on delivery. Therefore, before the first use, it must be
charged.
•Do not charge the battery for long periods of time. Do not completely drain the battery.
•Always keep in mind applicable safety instructions and protection requirements and environmental
legilsation.
•Check that the switch is in the off position.
•Connect the charger to the corresponding connector for the battery pack.
•Make sure the power is consistent with the rated values on the charger and adapter.
•When the red light is on the charger, it indicates that the battery is charging, and the green light
indicates that the charge is completed. The average charge time is 2 hours.
•When charging is complete, disconnect the battery pack from the power source.
•Ensure the battery it is recharged at least once every three months.
Operating Instructions
•Please wear suitable clothing and work gloves when using this equipment.
•Before each use, make sure the belt is running normally.
•Start/off switch and safety switch must be in working order.
•If the switch is damaged, stop using the device.
•Make sure the voltage of the power supply is consistent with the voltage on the rating label.
•The risk of injury can be reduced by wearing PPE and ensuring that the devices are functioning properly.
•In order to save the use of electric batteries and ensure the best service life do not cut wet and dry
branches over 60mm diameter and 20mm.
•When stopping operation, turn off the power switch and disconnect the battery box.
•When the device is running, keep your other hand at least 15cm away from the cutting area of the blade,
and kept well away from the blade.
•Do not force this equipment to cut bigger branches, otherwise the blade may deform or get stuck.
•In cold or humid weather, to protect the battery pack, put it under waterproof clothing, do not use this
equipment in the rain.
•We recommend that after daily use, battery pack should be disconnected, and the power switch (8)
turned off. The saw should be stored in the matching tool box.
•If the user feels the electricity is not strong enough or the cutting is not smooth enough, check if the
charge is exhausted or the blade is dull.

20V Pole One Handed Cordless Saw L249 Instructions for Use
Please read and retain these instructions for future reference v001: 26/10/22
The Enterprise
Department
UK Head Office, 11 Bridge Street, Bishop’s Stortford, CM23 2JU
Tel: [phone]*, Fax: [phone]
www.coopersofstortford.co.uk
EU address: D.S.B. LD, 160 Bd. de Fourmies, 59100 Roubaix, France
Tel: [phone]
*UK Calls cost around 7 pence per minute plus your telephone company’s network access.
Please check with your telephone supplier.
Attaching the Pole
Clip the saw on top of the pole and attach and
close the buckle

20V Pole One Handed Cordless Saw L249 Instructions for Use
Please read and retain these instructions for future reference v001: 26/10/22
The Enterprise
Department
UK Head Office, 11 Bridge Street, Bishop’s Stortford, CM23 2JU
Tel: [phone]*, Fax: [phone]
www.coopersofstortford.co.uk
EU address: D.S.B. LD, 160 Bd. de Fourmies, 59100 Roubaix, France
Tel: [phone]
*UK Calls cost around 7 pence per minute plus your telephone company’s network access.
Please check with your telephone supplier.
Cleaning and Maintenance
•Repair functions not mentioned herein shall be performed by the Service Centre.
•To ensure the safety of use, only the original parts can be used.
•Please switch off the equipment before starting any repair or maintenance.
•Clear the connection between the battery and the saw and store the battery in a safe package.
•Wear safety gloves when touching safety blades This can avoid sharp blade scratching the user.
•The following cleaning and maintenance must be carried out regularly. This ensures long-term and
reliable operation of the equipment.
Maintenance
•Clean the chain carefully after each use. Wipe the chain with lubricating oil and spray with metal
protection spray.
•Do not spray the equipment with water or expose it to water. This may cause electric shock.
•Keep the ventilator, motor housing and equipment handle clean.
•Use a damp cloth or brush cleaner.
•Do not use unsuitable cleaner. Otherwise this may cause the equipment to fail.
•Please clean the blade carefully after each use. Use oily cloth to wipe the blade and absorb the metal to
protect the blade.
•After 8 hours of continuous operation, please remove debris such as dust from the front cover plate of
the equipment.
Storage
•To ensure that the battery is fully charged, avoid storing the saw in extremely hot or cold environments.
•If the equipment will not be used for a long time, please remove the battery before storage.
•The battery and charger must be placed in the instrument box to prevent heat dust and moisture from
entering, check if the switch is off.
•Check the switch if close or not.
•The battery should be stored in a dry environment under:
•To ensure the service life of the equipment store it in a fully charged state.
•Storage temperature: -5°C - 30°C
•Do not turn on the power switch when storing.

20V Pole One Handed Cordless Saw L249 Instructions for Use
Please read and retain these instructions for future reference v001: 26/10/22
The Enterprise
Department
UK Head Office, 11 Bridge Street, Bishop’s Stortford, CM23 2JU
Tel: [phone]*, Fax: [phone]
www.coopersofstortford.co.uk
EU address: D.S.B. LD, 160 Bd. de Fourmies, 59100 Roubaix, France
Tel: [phone]
*UK Calls cost around 7 pence per minute plus your telephone company’s network access.
Please check with your telephone supplier.
PLUG WIRING (UK & IRELAND)
This appliance is supplied with a mains adaptor/charger with BS1363 plug pins.
DO NOT use If the socket outlets in your home or office are not suitable for this product’s mains adaptor/
charger plug pins. Attempts to insert the mains adaptor/charger into the wrong socket is likely to cause
electric hazard or damage.
DO NOT use with any other mains transformer/charger than the one that is supplied with this product.
CARE AND CLEANING INSTRUCTIONS
•Always switch off and unplug before cleaning.
•Do NOT immerse in water. Risk of electric shock.
•Do NOT use abrasive cleaners or sharp utensils to clean this appliance.
•Wipe surfaces with a soft dry cloth.
•Allow to dry thoroughly before further use.
•Store the appliance in a cool, dry place.
DISPOSAL
•Coopers of Stortford use recyclable or recycled packaging where possible.
•Please dispose of all packaging, paper, cartons, packaging in accordance with
your local recycling regulations.
•At the end of the product’s lifespan please check with your local council
authorised household waste recycling centre for disposal.
•Plastics, polybags –this is made from the following recyclable plastic.
Code & Symbol
Type of Plastic
Please Specify (includes ABS, Nylon)
Commonly used
for
CD’s, crisp packets, various flexible packaging, baby bottles, sunglass lenses
Notes
Not often or widely recucled