Victoria S95 User manual

1
Instructions Victoria S95/S96:
The storage bag for the Victoria can be used as backpack, shoulder bag and handbag. The backpack
straps are under the double bottom on the other side of the bag.
First, remove a bobbin, which is held in
place, in the bag, with an elastic.
Open the clasp of the strap that runs
across the post of the wheel.
Pull the black knob and lift the back
post up. You can release the knob after
you start to lift the post and it will
automatically lock in place once the
post is in its proper upright position.
Now open the clasp from the other strap
that keeps the wheel in its place.
Take the lazy kate out of the bag.
Place the cup on the footman over the
ball bearing of the wheel and push the
locking ring forward against the rim on
the cup. If you position the cup at an
angle to the bearing, while pushing it
on, the cup snaps on easier. When you
need to remove the cup again, retract
the locking ring and than twist the
footman, allowing the cup to snap off of
the bearing easily.
Take the spinning wheel out of the bag,
and remove the flyer from its storage
position. The shaft of the flyer is locked
into a nylon busing in the back rail.
Take the flyer out and slide the flyer
shaft through the bobbin, from the side
of the bobbin where there is no groove
in the bobbin rim.
With one hand hold the pulley, and with
the other hand push the flyer shaft into
the pulley. The slot at the end of the
flyer shaft fits over a pin inside the hole
of the pulley. Turn the flyer until the
slot in the flyer shaft fits over the pin in
the pulley. When successful, you will
feel the flyer snap slightly deeper into
the pin and you will not be able to turn
the flyer independent of the pulley. The
flyer shaft is held in place by a small
magnet inside the pulley.

2
Place the brake band in the groove of the bobbin and guide it around the hook.
Turning the black knob tightens the brake band around the bobbin end. You can see the brake
tension increase when the spring expands.
If you need to, you can adjust the friction of the knob by turning the screw that holds the knob.
By applying brake tension on the bobbin, you can control the tension on the yarn. The flyer turns
because it is connected to the pulley, which causes the twist in the yarn. Since the yarn connects the
bobbin to the flyer, the bobbin will turn. The result is that you feel a pull on the yarn, and by
tightening the brake, you will increase this pull. When the bobbin fills up, it will pull with a higher
torque on the brake. If you want to keep the same amount of pull on the yarn, you will need to
increase the brake tension. This also means that you will need more power to treadle as the bobbin
fills up. We suggest not to over fill the bobbin.
You can spin on the Victoria with one or two feet. Many people treadle with both feet, resulting in
lighter and smoother operation. If you use one foot, you have greater flexibility to position the
wheel away from you, or at a slight angle.
The main thing is to relax, and position yourself comfortably. You can spin well with a good
distance between your hands and the flyer orifice. The flyer and flyer orifice are angled upwards, in
the direction where you will naturally position your hands during spinning, but having the yarn
enter the flyer orifice at an angle is not a problem.
Put the drive band in one of the three
grooves of the pulley. The largest
diameter has a 1:6 ratio, and you will get
fewer twists per inch with the same
treadling speed compared to a higher
ratio.
With the drive band on the smaller pulley
diameters (ratio’s 1:9 and 1:13), you will
get more twists per inch, or you can spin
more yarn length in the same time. The
higher the ratio the more power the
treadling needs. This is where double
treadling helps.
Guide a starter thread through the orifice, around the hook and through the yarn guide slide. It does
not matter which side of the flyer you use. Attach the thread to the loop in the bobbin.
You can move the yarn guide slide as shown on the picture.
Toward yourself: Away from yourself:

3
The orifice has a removable nylon bushing inserted that gives you the choice between an 8 mm
(5/16") or 12 mm (1/2") orifice. The smaller diameter orifice is beneficial while spinning finer
yarns.
If the yarn guide becomes too easy to slide on
the flyer arms, you can use a pair of pliers to
tighten the guide, pushing it together where
the metal wire enters the plastic part.
Because it is a spring wire, you have to
squeeze so far that it does not spring back
completely to the old position.
If you tighten it too much, it is hard to open it
again, so the best way is to squeeze it a bit
more each time, and re-test.
The lazy kate has an extra hole in the middle.
An axle for a third bobbin will fit in this hole.
We supply a bobbin together with an axle,
cap and instructions as a kit.
For storage in the bag, the bobbin in the
middle has to be taken off and placed near
the flyer. The picture show you the tric to
store the lazy kate in the bag: While you are
folding the wheel, you have to turn the lazy
kate inward, so that the third axle comes
down between main wheel and brake knob.

4
If it happens that some play arises in the locking
system of the post, it can be repaired by adjusting
the buffer. Release the screw of the buffer and turn
it to a position so that it pushes the bottom of the
post slightly backwards. The locking knob should
fall inside just when the post hits the buffer. Fasten
the screw after the buffer is turned into its proper
position.
Putting the Victoria back into the bag:
After taking the bobbin off the flyer, place the flyer
in the nylon bushing on the back rail. Make sure
the hooks on the flyer are facing up. Place the drive
band behind the pulley to prevent it from being
under tension unnecessarily. The space behind the
pulley is also the right place to locate the brake
band when the flyer, with bobbin, is disconnected.
Position the spinning wheel into the bag, with the
rubber feet in the appropriate gaps of the base
plate. At this time, re-position the lazy kate.
Take the cup of the footman off of the ball bearing.
Attach the security strap over the cross piece, just before the post of the wheel.
Fold the wheel by first pulling the black knob out of it’s locking position and then attach the other
security strap across the back post.
Finally put the bobbin in place, with the elastic around the bobbins’groove, where the brake band
rest during normal operation.
When treadling the wheel without actually spinning yarn, you can experience an irritating sound.
This is the result of vibrations of the bobbin, due to the fact that there is no yarn pulling on the
bobbin.
Important:
During longer periods when you are not spinning, we recommend that you take the drive band out
of the pulley groove, and position the drive band in front or behind the pulley on the shaft.
Take care that no dirt accumulates in the hole of the pulley.
At the bottom of this hole is the locking magnet, which holds the flyer shaft in place. If some metal
parts do get into this hole, use a pair of tweezers to clear.