Schacht BABY WOLF LOOM Four Treadle Kit User manual

Find out more at schachtspindle.com
Schacht Spindle Company 6101 Ben Place Boulder, CO 80301
p. 303.442.3212 800.228.2553 f. 303.447.9273
© 2020 Schacht Spindle Company, Inc. 02.20
BABY WOLF LOOMTM &
MIGHTY WOLF LOOMTM
Four Treadle KiT
FL3061
FL3062
FL3063
FL3064
BABY WOLF WITH FOUR ADDITIONAL TREADLES
MIGHTY WOLF WITH FOUR ADDITIONAL TREADLES

– 2 –
ASSEMBLY
1. All looms: Detach all tie-up cords.
Remove the arrow peg under the brake
release pedal and remove the brake
cord from the pedal. Using a #2 Phillips
screwdriver, unscrew the two machine
screws holding the treadle support to the
inside legs (Figure 1). Let the barrel nuts
fall out of their holes. Set aside the screws
and barrel nuts for Step 6. Spread apart
the inside legs and remove the treadle
assembly.
2. All looms: From the right end of the
treadle bar, remove the washer and brake
release pedal. Remove the rst treadle
block on the right: use a #2 Phillips
screwdriver to remove the screw, then
slide the block off the treadle bar (Figure
2). Set aside these parts for the next step.
3. Baby Wolf only: Orient the new treadles
with the circular depression on the
underside.
From the left end of the treadle bar, slide
on a new treadle, a wooden spacer, a new
treadle, a wooden spacer, and the 5/8"
plastic spacer as shown in Figure 3.
From the right end of the treadle bar, slide
on a new treadle, a wooden spacer, a new
treadle, and the 3/4" plastic spacer. Slide
on the brake release pedal and washer
removed in Step 2; you can discard the
treadle block and its screw. Your treadle
assembly should now look like Figure 3.
Go to Step 5.
TOOLS REQUIRED
#2 Phillips screwdriver
slotted (at) screwdriver
BABY WOLF PARTS
4X regular or height extender
treadles
3X wood spacers
1X 5/8" plastic spacer
1X 3/4" plastic spacer
16X regular or height extender tie-ups
MIGHTY WOLF PARTS
4X regular or height extender
treadles
2X wood spacers
2X treadle blocks
2X #8 x 1-1/2" Phillips truss-head
sheet metal screws
16X regular or height extender tie-ups
FIGURE 2: REMOVE WASHER, BRAKE RELEASE
PEDAL, AND TREADLE BLOCK
rst treadle block
brake release pedal
& washer
FIGURE 1: REMOVE TREADLE ASSEMBLY
machine screw
barrel nut
right inside leg
treadle support

– 3 –
FIGURE 3: NEW TREADLES FOR BABY WOLF
5/8" plastic
spacer
3/4" plastic spacer
new treadles new treadles
wooden spacers wooden spacer
washer
brake
release
pedal
4. Mighty Wolf only: Orient the new
treadles with the circular depression on
the underside.
From the left end of the treadle bar, slide
on a new treadle, a wooden spacer, a new
treadle, and a treadle block as shown in
Figure 4.
From the right end of the treadle bar,
slide on a new treadle, a wooden spacer,
a new treadle, and a new treadle block.
Slide on the treadle block, brake release
pedal, and washer removed in Step 2.
Insert #8 x 1-1/2" Phillips truss-head
sheet metal screws through the holes in
the treadle support and attach the treadle
blocks using a #2 Phillips screwdriver.
Your treadle assembly should now look
like Figure 4.
FIGURE 4: NEW TREADLES FOR MIGHTY WOLF
treadle block
& screw
new treadles new treadles brake
release
pedal
wooden spacerwooden spacer
treadle blocks
& screws washer

– 4 –
5. All looms: Spread apart the inside
legs and move the treadle assembly into
position, making sure that the washer
stays in place on the right end of the
treadle bar. Line up the treadle assembly
with the holes in the leg that do not go
all the way through the legs—the treadle
bar ts into the large hole and the pin at
the end of the treadle support ts into the
small hole. Insert the pins and treadle bar
into their holes (Figure 5).
6. All looms: Collect the hardware
removed in Step 1. From underneath the
treadle support, place a barrel nut into
its hole and hold it in place with a slotted
screwdriver. Insert a machine screw
into an inner leg, from its outer side, and
tighten this screw rmly into the barrel
nut (Figure 6). Repeat on the other end of
the treadle support.
7. Re-attach all tie-ups and the brake
cord. Install 16 new tie-ups on the new
treadles, attaching them to the two empty
holes on each end of the lamms. •
barrel nut
machine screw
FIGURE 6: ATTACH TREADLE ASSEMBLY
FIGURE 5: ALIGN TREADLE ASSEMBLY
treadle bar
treadle support
pin
WolF loom accessories
WOLF TRAP
SECTIONAL BEAM
WOLF STROLLER
HIGH CASTLE TRAY
LOOM BENCH
DOUBLE BACK BEAM