Victory ROSE User manual

ROSE
Portable SPA

IMPORTANT SECURITY INSTRUCTIONS
Acrylic surfaces cannot be cleaned with acetone-based means.
The guarantee does not apply to acrylic surfaces destroyed by improper cleaning agents.
Following precautions and rules of procedures shall be implemented during
installation and use of ROSE bathtub:
REMARK! In order to reduce the risk SPA shall not be used by children without adults'
supervision.
In order to reduce the risk of getting wounded suction parts shall not be removed. Suction system is
adjusted to specific flows of water generated by pumps. The bathtub shall never be used if any of the
suction parts is defected. The filter and pumps implemented are compatible with regard to the water
flow. If any of those elements is to be changed that fact shall be remembered.
REMARK! Consumption of alcohol, drugs or medicines before using the bathtub may lead
to accidental drowning.
Obese persons as well as persons with heart problems. and persons with low or high blood
pressure and blood circulation problems, diabetics shall consult their doctors before using SPA.
Remember that wet surface can be slippery. Pay special attention while entering and exiting the
SPA stand only on steps and never on the bath edge.
Use the thermal lid when you do not use the bathtub.
Use specifics for bath water for water treatment; maintain appropriate pH (7,4 - 7,6).
Remark: for cleaning acrylic surfaces delicate soaps shall be implemented. The soaps shall not
include caustic agents.

2200 [l] + water tank 540 [l]
275[cm] x 235 [cm] x 100 [cm]
1. Description
6
Dimensions:
Capacity:
Number of seats:
- 42 x massage nozzles
- 3 x water pumps (2 x 1.5 kW, 1,1 kW)
- 1 x filter pump (1 x 0.75 kW)
- 3 x air nozzles (2 x 0.8 kW -
Air massage and 1 x 0.8 kW “Turbo”)
- Flow water heating unit 6 kW
- Sand filter
- Big whirling nozzles
- Medium whirling nozzles
- Medium permanent nozzles
- Mini whirling nozzles
Electronic control
LCD function display
Independent connection of two hydro massage sections
"Winter" program (antifreeze system)
"Awakening" from the winter program by SMS
Interactive communication by SMS
Water massage:
Whirling nozzles for back
Whirling nozzles for feet
Independent regulation of the water jet intensity by air system.
Turbo Charge system of massage nozzles (additional airing system of water by air nozzle)
Water level sensor (protection of the pump against operating without water)
Air massage:
Flexible regulation of air massage intensity
(B-MODE) pulse air massage
A watch
Daily and weekly filtration program
Built in RADIO FM and Mp3 player
Color underwater lightning - chromo therapy
Water temperature regulation - water flow heating unit with protection in case of water flow failure
Water proof remote control
Thermo insulation lid -10/15 cm
The system of easy opening of the lid
Acrylic cover with natural wood additions
Head supports
Ice container
!
!
!
!
!
!
!
!
1.Color underwater lightning - chromo therapy
2.Water suction - hydro massage
3.Water suction - filtration
4.Skimmer
5.Control desk
6.Loudspeakers
7.Air regulators
8.Section switch key
9.Ice container
10.Essence container (aromatherapy)
1
1
2 2 2
222
3
4
4
5
6
6
7
77
8
8
9
10
- Too large whirling super nozzles
-Too large whirling nozzles for feet
-Too large whirling nozzles for back

2. Place preparation
Portable SPA bathtub may operate inside as well as outside. The place where the bathtub is to be
installed shall meet the following conditions:
a) Appropriate space of the room (in case of closed rooms)
b) Appropriate size of the transport road,
c) Connected voltage of 3~400V and ensured efficiency of electric terminal, in case of standard
equipment power consumption of the bathtub amounts to 13,6 kW and requires electric cable of
5x4mm ,
d) Water terminal 3/4”
e) Sewage terminal 3/4”
f) Due to the danger of poring water over to the floor on which the bathtub is located the floor shall be
equipped with floor drain connected to the sewage system of the building. It is recommended to
construct around the bathtub a drain gutter covered by grate and connected to the sewage system of
the building as depicted in the drawing below. (In case of closed rooms).g) Stable and well leveled
foundation. The bathtub does not have the possibility of leveling,
h) Appropriate ventilation (in case of closed rooms).
2
I. Installation
Fig. Recommended construction of drain gutter
with connection to the sewage system in case of closed rooms

3. Transport of a bathtub.
It is recommended that the transport of bathtub be conducted in horizontal position in the original
packing of the producer on a wooden panel. It is possible to transport the bathtub in vertical position
after acrylic covers are removed. After taking from the pallet, the bathtub shall be transported by a
forklift. The base of the bathtub is adjusted to forklift transport. It is not allowed to handle cable and
other elements of massage system during transportation. It is not allowed t lean against bathtub
edges.
Places adjusted to forklift transportation
4. Preparation of water, sewerage and electrical connections.
To fill up the bath use the 3/4” connection showed in the figure below. The bath requires a permanent
connection to a water supply as this is indispensable for refilling any losses of water that emerge while
using the appliance. If there is a connection to a water supply refilling the bath with water takes place
automatically. Water level that is too low causes the filtration system, and as a consequence also the
water-heating system, to shut down.
While emptying the bath make sure that the appliance is connected to the sewerage system.
Fig. Places of electric, water and sewage terminals
Electric terminal of 13.6 kW
3~400 V
electric cable of 5x4 mm2
Sewage terminal 3/4”
The 3/4”water supply connection
Sewage terminal
backwash

L1-N 230 VAC
L2-N 230 VAC
L3-N 230 VAC
5
5 x 4 mm2
N
L1
L2
L3
PE
5
5 x 4 mm2
PE L3 L2 L1 N
Connection to a power source:
Feeder cable must be connected to a permanent installation of IP X5 security level.
Fitting of plug is not allowed. Permanent installation located in the wall may be connected
through the junction box. IP X5 junction box shall be located beyond the body of the bathtub
and above 20cm from the floor. Connection to a power source shall be conducted through a
cable of 5 x 4 mm through 25A power excess switch by standard installed in the bathtub.
Remark! Bathtub is equipped with feeder cables of the following colors:
Phase conductor L: black or brown
Neutral conductor N: blue
Protection conductor: yellow-green
2
!
!
!
Way of connection to a power source
Power excess switch
B 25/phase ln=0,03A
3 PHASES:

6. Filling up the sand filter with a filter bed.
The F400 sand filter is included in the standard equipment. The filter is equipped with a six-
function valve which controls the filter's work. The filter provided is unfilled. Before plumbing in
fill the filter with high-silica sand that acts as a filtering factor. To fill up the filter:
a
b
1. Open the torsional couplings a and b showed in the picture below.
5. SIM card installation of GSM operator
GSM module is located in the front, in the same place as other electronic elements. The box is
marked as GSM module. In order to install the card you should:
Disconnect the bathtub from the power source
Remove wooden panel of the cover
Remove the lid from the box containing GSM module
Remove the module from the box
Press a yellow key with the use of a sharp tool in order to cause SIM card feed to come out
Insert a SIM card in the feed
Push the SIM card feed to GSM module
Insert the module in the box, fix, screw the lid and install the wooden panel of the cover.
GSM module box
Information on the introduction of the PIN code and the system is presented hereinafter.
Clamp nuts of the six-function valve.

2. Unscrew the nuts clamping the six-function valve with the filter.
3. Disassemble the six-function valve.
Pipe cup
5. Fill up the filter with sand; first layer:25 kg of sand 2.0 0.6, second layer: 15 kg of sand 0.4-
0.8.
6. After filling up the filter take off the pipe cap, tighten the clamp nuts of the six-function valve
and the torsional couplings a and b (see point 1).
4. Blank off the pipe inside the filter so that the sand used during the filling up does not get to the pipe.

1 Suction of the filter pump A connected with the stilling basin,
3 Suction of the hydro-massage pump B connected with suction nozzles,
4 Hydro-massage pump piston connected with the tabulation of the hydro-massage,
6 filter-cleaning assist,
7 connection via an electrovalve to the water supply system
8 direct connection to the water supply system,
9 draining valves
E
B
C
C
D
S
K
7
J
I
8
B B
9
9
9
9
H
G
1
6
3
3
3
4
4
4
A
II. Operation
1. Bathtub connections diagram
A Filtration pump
B Hydro massage pump
C Air blower- air massage
D Air blower- Turbo Charging
E Electronics
F Temperature sensor
G Flow sensor
H 6 kW heater
I - Electric valve
J - Prefilter
K - Stilling basin
-Massage nozzles section
Z draining valves
Remark: In case of a breakdown all the valves shall be closed.
Do not regulate the valve marked as [S] service.
The whirlpool bath requires a permanent connection to the water supply. The bath housing is equipped
with a connection which ought to be connected to the water supply.

2. To fill up the bath:
1. Remove the easy-to-disassemble wooden parts of the bath housing placed on both front
sides of the whirlpool bath.
2. Check the position of the valves shut down all valves 9, 6, and 8. Valves 1, 3, 4, and 7 have
to remain opened.
3. Turn the power on.
After turning the power on, the whirlpool bath and the stilling basin begin to fill up. The process
of filling up continues to the point when the right water level is reached. To fully enjoy functions
of the bath make sure that the right water level has been reached.
In order to refill any losses of water the water supply ought to be permanently
connected to the bath. In case of overly low water level the filtration, the water heating
system and also the anti-frost system do not work. At low levels an overly low water
level may lead to bath damages.
3. Emptying the whirlpool bath and the stilling basin.
To empty the whirlpool bath use the sewerage connection at the front of the bath.
In order to empty the whirlpool bath, turn off all appliances and connect the hose with the 3/4”
ending to the drain at the front of the bath. Remove the wooden component of the bath housing
placed directly above the connection. This is where the draining valves 9 are placed. Open the
draining valves 9. After opening the valves the bath starts to empty.
7
8
I
J
7 The water supply conection across electric valve
8 Direct water supply connection
I - Electric valve
J - Prefilter
Use valve No to manual fill up the bath when
electric valve is damaged.
8
I
Filling: valve 7 - open
9
9
9
9
Emptying of the bath and basin
all valves 9 - opened
The 3/4”water supply connection
Sewage terminal 3/4”