Vidalux SS1200 User manual

INSTALLATION AND OPERATING MANUAL
INSTALLERS PLEASE NOTE, THESE
INSTRUCTIONS ARE TO BE LEFT WITH
THE CUSTOMER
SS1200 Rectangular
Technical Support: 01524 489939
Warranty Claims Or Delivery Damage: www.vidalux.co.uk
1

Live in a hard water area?? Limescale in the kettle and on bathroom fixtures?? Suffering from
unknown adverse health effects from this polluted drinking water??
If you have a steam shower and the generater becomes blocked with limescale and stops working
THIS IS NOT COVERED BY THE WARRANTY, as in reality it is not the products fault, it's the
poor quality water it has been subjected to
GOOD NEWS - Designed in partnership with one of the UK’s largest and most trusted water
softener manufacturers, this sleek, easy fit model is GUARANTEED to work or your money
back!! Remove all the limescale in a 1-4 bedroom home and benefit from the following
Better tasting drinking water - Easy to install - Guaranteed to work or your money back
No plumbing or chemicals – Cost as little as £2.00 a year to run and the improved condition of
the water pipes will reduce your heating bills - Made in the U.K - Trialled and tested Over 10
years | Used by professionals
VIDALUX CLEAR & BRIGHT WATER SOFTENER
Guaranteed to get rid of limescale
2

Thank you for purchasing this product. To guarantee the product delivers a long service life, please
ensure it is fi tted and used in accordance with the instructions contained in this booklet.
Please check that the boxes contain all the items listed below, and report to us any parts
that are missing or damaged prior to assembly and within 48 hours of receipt. Damages
noti ed to us after this time will be chargeable.
CAREFULLY CHECK THE PRODUCT IS AS ORDERED: CORRECT SIZE AND COLOUR OPTION BEFORE YOU
COMMENCE ANY OF THE INSTALLATION PROCESS
You should ensure that the  oor where the shower is to be located is smooth, level and able to support
the weight of the product when in use.
Please ensure that all connections are water tight, safe and insulated (where applicable) as the unit
has connections that are made for transport purposes only and are not fully tightened.
Refer also to contents list with images on the next pages.
Installation of the shower cabin is designed for a DIY installation. However any electric supply to
the unit itself is required by law to be installed by a qualified trades person to ensure safety and
quality. Failure to have the showers electric feed installed by qualified fitters will invalidate your
product guarantee and be dangerous.
No installation should take place until all items have been deemed cosmetically acceptable. Once installation
commences all products then enter into their governing warranty periods and no returns can be accepted, by
commencing with the installation you are accepting the goods cosmetic state with all 'workings' being
covered by warranty. (contact us for more information before installing if required)
3

ø 4mm
4

Serial Number Graphics Name Quantity Remark
01
02
03
04
05
06
07
08
09
1
1
2 L/R
2
2
22
2
2
2
ST4 ×16mm
ST4 ×25mm
L/R
L/R
L/R
L/R
10
11
32
1
12 1
13 36
14 1
ST4 ×10mm
5

Serial Number Graphics Name Quantity Remark
15
16
17
18
12
12
2
2
M4 ×20mm
19 2
20 8
21
22
23
24
25
26
27
8L/R
2
1
1
1
1
2
28 4
6

01
02
03
04
05
06
07
08
10
17
18
19
20
21
22
28
7

09
27
11
12
13
14
15
16
23
24
25
26
10
06
8

9

01
06
06
a
b
03
02
03
10

07
04
04
05
05
06
a c
b
28
11

10
08
08
09
09
12

10
13
11
12
13
Run a bead of sealant along
the join where the panels and
column sit ,to provide a
watertight barrier.
Remember to remove any
excess sealant once the panels
have been seated into position.

16 1513
14
14

19
18
20
b
a17
17
15

21
21
22
22
10
ab
16

23
17

24
18

LEVELING AND FITTING THE TRAY
Remove the protective  lm covering the base.
Connect the soil pipe, trap and any couplings to the  exible waste under the tub. You may choose to
 t either a HEPV0 trap with the appropriate couplings or choose to  t a McAlpine ST28M coupling to a
McAlpine 28-NRV trap.
Position the tub base in what will be its  nal location and adjust the feet until the base is level. You can
raise/lower the feet under the tub and with a spirit level laid across the tub, ensure the tub is level.
Now  ll the base with some water and check that the water  ows adequately to the plug and exits
satisfactorily. If the water does not  ow to the plug fully, then you will need to increase the fall on the
tray by adjusting the legs. If the water does not exit the waste section fast enough, then ensure there is
suitable fall in the waste pipe and/or no blockage or kinks in the pipe work.
Check and attend to any leaks.
Now slide the tub away from the wall to allow access all around the shower as you assemble.
This product is freestanding so you do not need to  x the feet to the  oor.
19

06
13
27
06
13
a
b
c
25
26
Run a bead of sealant along
the tray where the panels will
sit to provide a watertight
barrier.
Remember to remove any
excess sealant once the panels
have been seated into position.
20