Video Products ST-POE-WTP Instruction Manual

6732(:73
:DWHUSURRI3RZHU2YHU(WKHUQHW([WHQGHU
8VHU0DQXDO
0$15(9

Certification
FCC compliance Class A: This equipment has been tested and
found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the user
will be required to correct the interference at his
own expense.
ACMA
compliance Notice! This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be
required to take adequate measures.
European Union
directives 2004/108/EC (EMC directive): Hereby, UTC Fire & Security declares that this device is in
compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC

i
Contents
Package Contents 1
Product Features 1
Product Overview 2
Port Connections 
In Port 
Out Port 
Hardware Installation 
Before Installation 
Power Source Equipment (PSE) Installation 
Powered Device (PD) Installation 
Multiple PoE Extender Installation 
Specifications 

1
Package Contents
Thank you for purchasing the S7 POE:73 :DWHUSURRI
*LJDELW3RZHURYHU Ethernet Extender.
Product Features
•Complies with IEEE 802.3af DW32(Power over
Ethernet
• Extends the range of PoE an additional 100 meters (328ft.)
• Forwards both Ethernet data and PoE power to a remote
device
•Auto-detection of POE IEEE 802.3at 32(equipment and
devices to prevent damage caused by incorrect installation.
•Multiple units can be daisy-chained for extended distance
(max. units)
• No external power required
• Compact size, Wall-mountable design
:DWHUSURRI,3GHVLJQ
&$7[FDEOHZLWKDPPPP2'LVUHFRPPHQGHG
IRUZDWHUSURRILQJ


Port Connections
In Port
Connect the PoE IN port from following 802.3af PSE type
devices through a CAT-5e/6 UTP673 cable:
• PoE injector
• PoE Injector Hub
• PoE Ethernet Switch
• Another 67POE:73
Out Port
Connect the PoE OUT port to following 802.3af PD type
devices through a CAT-5e/6 UTP673 cable:
• PoE IP Camera
• PoE VoIP Phone
• PoE Wireless AP
• PoE Splitter
• Another 67POE:73
1RWH7RSDVVWKHFDEOHWKURXJKWKHVHDOVTXHH]H
WKHVHDOWRH[SRVHWKHVSOLW7KHVHDOLVSUHVSOLW
WRDOORZSUHWHUPLQDWHGSDWFKFDEOHVWREHXVHG


Hardware Installation
The 67POE:73 operates at tKUHH different data rates –
10Mbps00MbpsDQG0ESV in the same device and
automatically adjusts based on the speed of incoming connection.
The following section describes the hardware features of the
67POE:73. Carefully read this section before connecting
any network device to this unit.
Before Installation
It is recommended to check the network environment
before the installation. The 67POE-:73 conveniently
extends the distances in an installation base by transferring
power to the remote PDs. (Powered Devices).
The 67POE-:73 is installed between the PSE (Power
Source Equipment) and the PD (Powered Device); it is
powered by PSE and forwards the Ethernet data and
remaining POE power to the PD. The 67POE-:73 doesn’t
require an external power supply and it can be installed easily
just plug and play; that means the operator does not need to
configure the 67POE-:73. The 67POE-:73 injects power
to the PDs without affecting the data transmission
performance. It offers a cost effective and quick solution to
extend power and data for an additional 328 ft. (100m).
Note: The 67POE-:73 can be installed with third-party
devices as long as the connected device complies with
the IEEE 802.3af RU,(((DW32(standardV.
Power Source Equipment (PSE) Installation
1. 5HPRYHWKHOLTXLGWLJKWUHVWUDLQWFDSDQGFonnect a standard
Cat5e/6 cable from Power SourceEquipment (PSE), such as
PoE Switch, PoE Injector hub ora single port PoE injector, to
the “IN” port of 67POE-:73.


2. The PSE delivers both Ethernet Data and PoE power over
the UTP cable to the 67POE-:73
Powered Device (PD) Installation
1. Connect one side of the CAT5e/6 cable to the "OUT" port
of the 67POE-:73, and the other side to the PD.
2. The "OUT" port injects power and transfers data to the PD.
Figure 2: Extender connection diagram
Note: The 67POE-:73will not inject power to a PD that
doesn't comply to the IEEE 802.3af standard.
1RWH:KHQUHDSSO\LQJWKHFDSRIWKHOLTXLGWLJKW
UHVWUDLQWWRWKHUHWUDLQWERG\EHVXUHWRWLJKWHQ
VHFXUHO\WRVTXHH]HWKHVHDODJDLQVWWKHFDEOH