Videx 2213 User manual

2213 REMOTE RELAY
Remote Relay for the VX2200 System
2213-66251540-EN
V2.0
10/10/22
Technical Manual
ENG
We recommend that this equipment is
installed by a Competent Electrician,
Security or Communications Engineer.

2213-66251540-EN - V2.0 - 10/10/22
- 2 -
2213 Remote Relay - Technical Manual
2213 Remote Relay for the VX2200 System
All Countries:
VIDEX ELECTRONICS S.P.A.
www.videx.it - [e-mail]
Tel: [phone] - Fax: [phone]
UK Customers:
VIDEX SECURITY LTD.
www.videxuk.com - [email protected]
Tech Line: 0191 224 3174
CUSTOMER SUPPORT
Theproduct isCEmarkeddemonstratingits conformity and isfordistribution
within all member states of the EU with no restrictions. This product follows
the provisions of the European Directives 2014/30/EU (EMC); 2014/35/EU
(LVD); 2011/65/EU (RoHS): CE marking 93/68/EEC.
DECLARATION OF RESPONSIBILITY
This technical manual has been written and revised carefully. The guidance and the descriptions which are included in it are in
reference to VIDEX parts and are correct at the time of print. However, subsequent VIDEX parts and technical manuals, can be
subject to changes without prior notice. VIDEX Electronics S.P.A. and VIDEX Security Ltd. (UK) cannot be held responsible for
damages caused directly or indirectly by errors, omissions or discrepancies between the VIDEX parts and the technical manual.
The product is UKCA marked demonstrating its conformity and is for
distributionwithintheUK.Thisproduct followsthe provisionsofthefollowing
UK legislation: Electromagnetic Compatibility Regulations 2016; Electrical
Equipment (Safety) Regulations 2016; Radio Equipment Regulations 2017
and The Restriction of the Use of Certain Hazardous Substances in Electrical
and Electronic Equipment Regulations 2012 (RoHS).
MANUFACTURER
VIDEX ELECTRONICS S.P.A.
Via del Lavoro, 1 - 63846 Monte Gilberto (FM) Italy
Tel: [phone] - Fax: [phone]
www.videx.it - inf[email protected]
THE POWER TO SECURE
IT IS RECOMMENDED THAT THIS VIDEX PRODUCT IS INSTALLED BY A COMPETENT AND QUALIFIED
ELECTRICIAN, SECURITY INSTALLATION SPECIALIST OR COMMUNICATIONS ENGINEER.
Contents
Manual Introduction .........................................................................................................................................................................3
Description and Operation...............................................................................................................................................................3
Relay Terminal Connections .............................................................................................................................................................3
Dip-switch Settings ...........................................................................................................................................................................4
Installation Notes ..............................................................................................................................................................................6
Lock Release Wiring and back EMF Protection ...............................................................................................................................6
Technical Specication......................................................................................................................................................................6
Wiring Diagram..................................................................................................................................................................................7
Notes...................................................................................................................................................................................................8

2213-66251540-EN - V2.0 - 10/10/22
3
2213 Remote Relay - Technical Manual
2213 Remote Relay for the VX2200 System
MANUAL INTRODUCTION
The information in this manual is intended as an installation and commissioning guide for the 2213LIFT remote relay. This manual
should be read carefully before the installation commences.
Any damage caused to the equipment due to faulty installation where the information in this manual has not been followed is not the
responsibility of VIDEX Electronics S.P.A. and VIDEX Security Ltd (UK).
It is recommended that the remote relay is installed by a competent electrician, security or communications engineer.
For UK customers Videx run free training courses for engineers who are unfamilier or who have not installed this product before.
Technical help is also available for UK and Rep. of Ireland customers from the Videx technical helpline on tel: [phone] during
oce hours (8:30am - 5:00pm MON to FRI) or via e-mail: [email protected].
For all other overseas customers including Europe technical help is available on tel: [phone] or via e-mail: [email protected].
A copy of this technical manual can also be downloaded from the Videx websites: www.videxuk.com, www.videx.it.
DESCRIPTION AND OPERATION
The 2213 remote relay module is designed to work on the VX2200 system. All entrance panels on the VX2200 system include the
lock release relay and push to exit button input inside the entrance panel. For higher security applications including installations in
compliance with Secured by Design the 2213 enables the relay and push to exit button input to be installed in a secure location away
from the entrance. Setting up of the module is achieved using the 8 way dip-switches.
The 2213 device number should be set to match the device number (panel ID) of the entrance panel it is associated with using dip
switches 1-4. When the relay command is received from an audiophone or videophone, from an digital entry panel (via the coded
access facility) or a concierge the relay will activate for the programmed relay time (setup using dip-switches 5-7).
Activating the PTE input on the 2213 will also trigger the relay for the programmed relay time. Lock release cables and push to exit
cables should not run through the entrance panel back box or any unsecure locations to maintain the highest security possible. The
relay in the entrance panel along with the PTE input in the entrance panel will not be used and should remain disconnected (in the
event of someone activating the PTE input on the entrance panel it will have not eect on the 2213 remote relay).
The 2213 can also be setup in local mode (default) or main mode (using dip-switch 8) for larger systems that have main entrances
and local/sub entrances where 2206N bus exchange devices are used. The module includes connections for 12Vdc power, digital BUS
connections (L, -) and a set of relay contacts (CO, NO, NC).
RELAY TERMINAL CONNECTIONS
Refer to the table below for the 2213 terminal connections and the unit layout and dimensions in Fig.1.
22
66
50
60
A B C D E F
LEGEND
Firmware version - FW10.LX
Relay (NC/NO/CO) terminals
8 way programmable dip-switches
PTE input (switched 0V)
Databus input (L/-)
+12Vdc power input
Fig. 1
Terminal Description Terminal Description
12Vdc 12-14Vdc input from power supply PTE Push to exit input (switched 0V push to make)
GND 0V input from power supply CO Common relay connection
-Databus 0V connection NO Normally open relay connection
LDatabus connection (+pos) NC Normally closed relay connection

2213-66251540-EN - V2.0 - 10/10/22
4
2213 Remote Relay - Technical Manual
2213 Remote Relay for the VX2200 System
DIPSWITCH SETTINGS
Dip-switches SW1 to SW4 (see Fig.2) sets up the device number (panel ID) of the 2213 remote relay.
Setting Device Number
Device No. (Panel ID) SW1 SW2 SW3 SW4 Switch Position
1OFF OFF OFF OFF
56781234
ON
2ON OFF OFF OFF
56781234
ON
3OFF ON OFF OFF
56781234
ON
4ON ON OFF OFF
56781234
ON
5OFF OFF ON OFF
56781234
ON
6ON OFF ON OFF
56781234
ON
7OFF ON ON OFF
56781234
ON
8ON ON ON OFF
56781234
ON
9OFF OFF OFF ON
56781234
ON
10 ON OFF OFF ON
56781234
ON
11 OFF ON OFF ON
56781234
ON
12 ON ON OFF ON
56781234
ON
13 OFF OFF ON ON
56781234
ON
14 ON OFF ON ON
56781234
ON
15 OFF ON ON ON
56781234
ON
16 ON ON ON ON
56781234
ON
12345678
Unit Address
NC NO CO
12Vdc GND _PTEL
2213N
VX2200 Remote Relay
VIDEX
12345678
Fig. 2 SW1 to SW4

2213-66251540-EN - V2.0 - 10/10/22
5
2213 Remote Relay - Technical Manual
2213 Remote Relay for the VX2200 System
Dip-switches SW5 to SW7 (see Fig.3) sets up the relay time of the 2213.
Setting the Relay Time
Relay Time SW5 SW6 SW7 Switch Position
1 second OFF OFF OFF
56781234
ON
2 seconds ON OFF OFF
56781234
ON
4 seconds OFF ON OFF
56781234
ON
6 seconds ON ON OFF
56781234
ON
8 seconds OFF OFF ON
56781234
ON
10 seconds ON OFF ON
56781234
ON
12 seconds OFF ON ON
56781234
ON
15 seconds ON ON ON
56781234
ON
12345678
Unit Address
NC NO CO
12Vdc GND _PTEL
2213N
VX2200 Remote Relay
VIDEX
1234567856781234
Fig. 3 SW5 to SW7
Dip-switch SW8 (see Fig.4) sets up the operating mode of the 2213 remote relay, as shown in the table below.
Setting Mode
Operating Mode SW8 Switch Position
Local mode (default) OFF
56781234
ON
Main mode ON
56781234
ON
12345678
Unit Address
NC NO CO
12Vdc GND _PTEL
2213N
VX2200 Remote Relay
VIDEX
123456785678123456781234
Fig. 4 SW8

2213-66251540-EN - V2.0 - 10/10/22
6
2213 Remote Relay - Technical Manual
2213 Remote Relay for the VX2200 System
INSTALLATION NOTES
When installing the 2213LIFT remote relay follow the list of installation checks below:
• Check that all components are free from damage before installing, do not proceed with the installation in the event of
damage.
• Keep all packaging away from children (please dispose of any excess waste and packaging responsibly).
• Do not obstruct the ventilation openings or slots on any of the devices.
• All connections to mains voltages must be made to the current recognised national standards: I.E.T. Wiring Regulations,
Eighteenth Edition BS7671:2018 for the UK or the appropriate standards of your country if installing overseas.
• Install an appropriate fused spur or isolation switch to isolate the mains supply.
• Isolate the mains supply before carrying out any maintenance work on the system.
• Avoid water ingress into the module.
• If an electric lock is to be tted to the system it is important to power the lock release from a dedicated fused supply to avoid
a short in the device cabling. Remember to power down the lock release when tting it.
• All intercom and access control cables must be routed separately from the mains.
LOCK RELEASE WIRING AND BACK EMF PROTECTION
When tting an electric lock release back EMF protection will be required. If tting an AC lock release then a 100nF ceramic disc
capacitor should be tted across the terminals of the lock, shown in Fig.5. If tting a DC lock release (fail secure or fail safe) then a
1N4002 diode should be tted across the terminals on the lock, shown in Fig.6.
12V AC
LOCK RELEASE
100nF
CAP
A varistor (MOV) can be tted
to either an AC or DC lock
across the lock terminals and
is not polarity conscious
DIODE
1N4002
12V DC
LOCK RELEASE
Fig. 5 Fig. 6
If a 100nF ceramic disc capacitor or a 1N4002 diode are not available then a 14 - 20V MOV (metal oxide varistor) can be tted across
the lock terminals instead (refer to Fig.5 above) and can be tted on both an AC and DC lock. A lock release connection example
can also be seen in Fig.7 wiring diagram on page 7.
TECHNICAL SPECIFICATION
Input voltage: 12V - 14Vdc power input (+/-10%)
Current (standby): 6.4mA (max.)
Curent (during operation): 41mA (max.)
PTE input open voltage: 5Vdc
PTE input closed voltage: 0V
Databus voltage: 7.5V - 8Vdc (L/-)
Maximum cable resistance: 7Ω
Relay contacts: CO, NO and NC (10A @ 24Vdc, 12A @ 120Vac, 5A @ 250Vac)
Programming: Programming via 8 way dip-switches: device ID setup ID.1 - ID.16, relay activation time setup
(1, 2, 4, 6, 8, 10, 12 or 15 seconds), operating mode local mode (default) or main mode (to
operate with 2206N bus exchange devices).
Enclosure material: ABS plastic (white)
Enclosure dimensions (mm): 66 (W) x 60 (H) x 22 (D)
Mounting: Surface, direct wall xing

2213-66251540-EN - V2.0 - 10/10/22
7
2213 Remote Relay - Technical Manual
2213 Remote Relay for the VX2200 System
WIRING DIAGRAM
Fig.7 below shows the wiring connections for the 2213 remote relay.
Made in Italy
Dry contact output
Capacitor discharge
Balanced V1, V2
Coax V2 = V, V1
not used
RS485
BUS TERMINATION
Open
Close
V.PB.CHIP
Balance
A
B
GND
D0
D1
LR
LG
OC OUTPUT
RS485
WIEGAND
USB
12345678
12345678
ON
12Vdc
Fail Secure
Lock Release
Push to Exit
(push-to-make)
1 2 3 4 5 6 7 8
ON
12345678
ON
1 2 3 4 5 6 7 8
ON
12345678
ON
Art.3171, Art.3172 or Art.3176 PHONE ID.1
12V GND L
Panel set as MASTER,
Local mode and
Device (Panel) ID.1
Art.4212R
Digital Panel
Remote relay set
to ID.1, relay time
set for 6 seconds
Art.KRA76 or Art.KRA78 PHONE ID.2
CONTROL EQUIPMENT
IN SECURED LOCATION
The 12Vdc Lock release can
be activated from any of the
audiophones on the system
or by entering the correct
door access code on the
Art.4212R Digital Panel
Fig. 7

2213-66251540-EN - V2.0 - 10/10/22
- 8 -
2213 Remote Relay for the VX2200 System
2213 Remote Relay - Technical Manual
NOTES

2213-66251540-EN - V2.0 - 10/10/22
- 9 -
2213 Remote Relay for the VX2200 System
2213 Remote Relay - Technical Manual

2213-66251540-EN - V2.0 - 10/10/22
- 10 -
2213 Remote Relay for the VX2200 System
2213 Remote Relay - Technical Manual

2213-66251540-EN - V2.0 - 10/10/22
- 11 -
DISPOSAL
In accordance with the Legislative Decree no. 49 of 14 March 2014 “Implementation of the Directive 2012/19/EU on waste
electrical and electronic equipment (WEEE)”.
The crossed-out bin symbol on the equipment or on the packaging indicates that when the product reaches the end of
its lifetime, it must be collected separately from mixed municipal waste. The user must, therefore, dispose of the equip-
ment at the end of its lifetime in the suitable waste collection centres or bring it to the retailer during the purchase of a
new equipment of equivalent type at the ratio of one-to-one. Furthermore, the user is allowed to dispose of the WEEEs
of very small size (domestic appliances without any external dimension exceeding 25 cm (9.84 inches) for free to the
retailers, without any purchase obligation. The correct waste disposal of the WEEEs contributes to their reuse, recycling
and recovery and avoids potential negative eects on the environment and human health due to the possible presence
of dangerous substances within them.
SMALTIMENTO
Ai sensi del Decreto Legislativo 14 marzo 2014, n° 49 “Attuazione della direttiva 2012/19/UE sui riuti di apparecchiature
elettriche ed elettroniche (RAEE)”.
Il simbolo del cassonetto barrato riportato sull’apparecchiatura o sulla sua confezione indica che il prodotto alla ne della
propria vita utile deve essere raccolto separatamente dagli altri riuti urbani misti. L’utente dovrà, pertanto, conferire l’appar-
ecchiatura giunta a ne vita presso gli idonei centri di raccolta dierenziata oppure riconsegnarla al rivenditore al momento
dell’acquisto di una nuova apparecchiatura di tipo equivalente, in ragione di uno a uno. L’utente ha, inoltre, la possibilità di
conferire gratuitamente presso i distributori, senza alcun obbligo di acquisto, per i RAEE di piccolissime dimensioni (per le
apparecchiature di tipo domestico con nessuna dimensione esterna superiore a 25 cm).
L’adeguata raccolta dierenziata dei RAEE contribuisce al loro riutilizzo, riciclaggio e recupero ed evita potenziali eetti neg-
ativi sull’ambiente e sulla salute umana dovuti alla eventuale presenza di sostanze pericolose al loro interno.
ÉLIMINATION
Conformément au décret législatif n ° 49 du 14 mars 2014 relatif à l’«Application de la directive 2012/19 / UE relative aux
déchets d’équipements électriques et électroniques (DEEE)».
Le symbole de la poubelle barrée sur l’équipement ou sur son emballage indique que le produit en n de vie utile doit être
collecté séparément des autres déchets municipaux en mélange. L’utilisateur doit donc remettre l’équipement en n de
vie aux centres de collecte appropriés ou le restituer au revendeur lors de l’achat d’un nouveau type d’équipement équi-
valent, dans le rapport de un à un. De plus, l’utilisateur a la possibilité de conférer gratuitement aux distributeurs, sans au-
cune obligation d’achat, de très petits DEEE (pour les appareils ménagers sans dimensions extérieures supérieures à 25 cm).
La collecte séparée adéquate des DEEE contribue à leur réutilisation, leur recyclage et leur valorisation et évite les éventuels
eets négatifs sur l’environnement et la santé humaine en raison de la présence possible de substances dangereuses dans
ceux-ci.
ELIMINACIÓN
De conformidad con el Decreto legislativo n. 49 de 14 de marzo 2014 “Aplicación de la Directiva 2012/19/UE relativa a resi-
duos de aparatos eléctricos y electrónicos (RAEE)”.
El símbolo del contenedor tachado indicado sobre los aparatos o sobre los embalajes señala que el producto al nal de su
vida útil debe ser recogido separadamente de otros residuos municipales mezclados. Por tanto, el usuario deberà conferir los
aparatos al nal de su vida útil en los apropriados centros de recogida selectiva o devolverlos al revendedor al momento de
la compra de nuevos aparatos equivalentes, en una relación de uno a uno. Además, el usuario tiene la posibilidad de entre-
gar sin cargo a los distribuidores, sin ninguna obligación de compra, los RAEEs muy pequeños (para electrodomésticos sin
dimensiones externas superiores a 25 cm).
La recogida selectiva apropriada de los RAEEs contribuye a su reutilización, reciclaje y valorización y evita potenciales impactos
negativos sobre el medio ambiente y la salud humana debidos a la possible presencia de substancias peligrosas dentro de ellos.
ELIMINAÇÃO
De acordo com o Decreto Legislativo n.º 49 de 14 de março de 2014“Implementação da Diretiva 2012/19/UE relativa
aos resíduos de equipamentos elétricos e eletrónicos (REEE)”.
O símbolo do caixote do lixo riscado no equipamento ou na embalagem indica que quando o produto atinge o fim
da sua vida útil, deve ser recolhido separadamente dos resíduos urbanos mistos. O utilizador deve, portanto, elimi-
nar o equipamento no final da sua vida útil nos centros de recolha de resíduos adequados ou levá-lo ao vendedor
durante a compra de um novo equipamento de tipo equivalente, na proporção de um para um. Além disso, o utili-
zador pode eliminar gratuitamente os REEE de dimensões muito reduzidas aos vendedores, sem qualquer obrigação
de compra.(só aparelhos domésticos sem qualquer dimensão externa que exceda 25 cm, ou seja 9,84 polegadas).
A correta eliminação dos REEE contribui para a sua reutilização, reciclagem e recuperação e evita potenciais efeitos
negativos sobre o ambiente e a saúde humana devido à possível presença de substâncias perigosas no seu interior.
VERWIJDERING
In overeenstemming met het Wetsbesluit nr. 49 van 14 maart 2015 “Implementatie van de Richtlijn 2012/19/EU
inzake afgedankte elektrische en elektronische apparaten (AEEA)”.
Het doorgekruiste vuilnisbaksymbool op het apparaat of de verpakking geeft aan dat het product aan het einde van
zijn levensduur niet samen met het gewone huisvuil weggegooid mag worden. De gebruiker moet het apparaat aan
het einde van zijn levensduur inleveren bij een gepast inzamelpunt of de winkel waar hij een nieuw apparaat van
een gelijksoortig type zal kopen. De gebruiker kan tevens AEEA’s van een zeer klein formaat (huishoudapparaten
met een buitenafmeting kleiner dan 25 cm (9,84 inch) gratis en zonder enige aankoopverplichting bij handelaars
inleveren. Een juiste verwijdering van AEEA’s draagt bij tot hergebruik, recycling en terugwinning, en voorkomt
potentiële negatieve effecten op het milieu en de menselijke gezondheid door de mogelijke aanwezigheid van
gevaarlijke stoffen.
2213 Remote Relay for the VX2200 System
2213 Remote Relay - Technical Manual

The product is CE marked demonstrating its conformity and is for distribution with-
in all member states of the EU with no restrictions. This product follows the provi-
sions of the European Directives 2014/30/EU (EMC); 2014/35/EU (LVD); 2011/65/EU
(RoHS): CE marking 93/68/EEC.
Il prodotto è marchiato CE a dimostrazione della sua conformità e può essere distri-
buito liberamente all’interno dei paesi membri dell’Unione Europea UE.
Questo prodotto è conforme alle direttive Europee: 2014/30/UE (EMC); 2014/35/UE
(LVD); 2011/65/UE (RoHS): marcatura CE 93/68/EEC.
Le produit est marqué CE à preuve de sa conformité et peut être distribué librement
à l’intérieur des pays membres de l’union européenne EU.
Ce produit est conforme aux directives européennes 2014/30/EU (EMC) ; 2014/35/
EU (LVD) ; 2011/65/EU (RoHS): marquage CE 93/68/EEC.
El producto lleva la marca CE que demuestra su conformidad y puede ser distribuido
en todos los estados miembros de la unión europea UE.
Este producto cumple con las Directivas Europeas 2014/30/EU (EMC); 2014/35/EU
(LVD); 2011/65/EU (RoHS): marca CE 93/68/EEC.
Het product heeft de CE-markering om de conformiteit ervan aan te tonen en is be-
stemd voor distributie binnen de lidstaten van de EU zonder beperkingen. Dit pro-
duct volgt de bepalingen van de Europese Richtlijnen 2014/30/EU (EMC); 2014/35/
EU (LVD); 2011/65/EU (RoHS): CE-markering 93/68/EEG.
O produto tem a marca CE que demonstra a sua conformidade e destina-se a dis-
tribuição em todos os estados membros da UE, sem restrições. Este produto segue
as disposições das Diretivas Europeias 2014/30/UE (EMC); 2014/35/UE (LVD);
2011/65/UE (RoHS): marcação CE 93/68/CEE.
         CE      
                 
  (RoHS)  EU// ;(EU (LVD// ;(EU (EMC// 
EEC// CE  
MANUFACTURER
FABBRICANTE
FABRICANT
FABRICANTE
FABRIKANT
FABRICANTE
   
VIDEX ELECTRONICS S.P.A.
Via del Lavoro, 1
63846 Monte Giberto (FM) Italy
Tel [phone]
Fax [phone]
www.videx.it - inf[email protected]
CUSTOMER SUPPORT
SUPPORTO CLIENTI
SUPPORTS CLIENTS
ATENCIÓN AL CLIENTE
KLANTENDIENST
APOIO AO CLIENTE
 
VIDEX ELECTRONICS S.P.A.
www.videx.it
[email protected]
Tel: [phone]
Fax: [phone]
UK Customers only:
VIDEX SECURITY LTD
www.videxuk.com
Tech Line: 0191 224 3174
[email protected]
Portugal oce:
VX IBÉRIA, UNIPESSOAL LDA
Rua Tenente Mário Grilo, 26 D, E, F
4200-397 Porto
Phone: [phone]
www.videx.it
[email protected]
Singapore oce:
VIDEX ASIA PACIFIC PTE LTD
1 TAMPINES NORTH DRIVE 1,
#06-08, T-Space
Singapore 528559
Phone: [phone]
[email protected]
Main UK oce:
VIDEX SECURITY LTD
1 Osprey Trinity Park
Trinity Way
LONDON E4 8TD
Phone: [phone]
www.videxuk.com
[email protected]
Northern UK oce:
VIDEX SECURITY LTD
Unit 4-7
Chillingham Industrial Estate
Chapman Street
NEWCASTLE UPON TYNE - NE6 2XX
Tech Line: ([phone]
Phone: [phone]
Greece oce:
VIDEX HELLAS Electronics
48 Filolaou Str.
11633 ATHENS
Phone: [phone]
([phone]
Fax: [phone]
www.videx.gr
[email protected]
Danish oce:
VIDEX DANMARK
Hammershusgade 15
DK-2100 COPENHAGEN
Phone: [phone]
Fax: [phone]
www.videx.dk
[email protected]
Benelux oce:
NESTOR COMPANY NV
E3 laan, 93
B-9800 Deinze
Phone: [phone]
Fax: [phone]
www.nestorcompany.be
[e-mail]
Dutch oce:
NESTOR COMPANY BV
Business Center Twente (BCT)
Grotestraat, 64
NL-7622 GM Borne
www.videxintercom.nl
[e-mail]