Viessmann Vitodens 222-F Quick start guide

VIESMANN VITODENS
Gas condensing boilers
VITODENS 222-F Type B2TB
Gas condensing storage combi boiler
1.9 to 35.0 kW
For natural gas and LPG
VITODENS 222-F Type B2SB
Gas condensing storage combi boiler
1.9 to 26.0 kW
For natural gas and LPG
VITODENS 242-F Type B2UB
Gas/solar condensing storage combi boiler with solar
DHW heating
1.9 to 26.0 kW
For natural gas and LPG
5822 431 GB 5/2016
Technical guide

Index
1. Vitodens 222-F, type B2TB 1.1 Product description ....................................................................................................... 4
1.2 Specification ................................................................................................................. 6
2. Vitodens 222-F, type B2SB 2.1 Product description ....................................................................................................... 11
2.2 Specification ................................................................................................................. 13
3. Vitodens 242-F, type B2UB 3.1 Product description ....................................................................................................... 18
3.2 Specification ................................................................................................................. 20
4. Installation accessories 4.1 Installation accessories Vitodens 222-F and Vitodens 333-F ....................................... 26
4.2 Installation accessories Vitodens 242-F ....................................................................... 32
5. Design information 5.1 Siting, installation .......................................................................................................... 36
■ Siting conditions for open flue operation (appliance type B) ..................................... 36
■ Siting conditions for room sealed operation (appliance type C) ................................ 37
■ Operation of the Vitodens in wet rooms .................................................................... 38
■ Electrical connection ................................................................................................. 38
■ Gas connection ......................................................................................................... 39
■ Minimum clearances ................................................................................................. 39
■ Installation Vitodens 222-F and 333-F ...................................................................... 40
■ Installation Vitodens 242-F ....................................................................................... 49
5.2 Decision-making aids for DHW heating ........................................................................ 55
■ Information on water quality ...................................................................................... 55
5.3 Connections on the water side ..................................................................................... 56
■ Connections on the DHW side .................................................................................. 56
5.4 Condensate connection ................................................................................................ 58
■ Condensate drain pipe and neutralisation ................................................................ 58
5.5 Hydraulic connection .................................................................................................... 59
■ General information .................................................................................................. 59
■ Expansion vessels for the heating circuit .................................................................. 60
■ Expansion vessel and heat sink for the solar circuit ................................................. 61
■ Low loss header ........................................................................................................ 64
5.6 Sizing the solar thermal system .................................................................................... 64
■ Influence of orientation, inclination and shade .......................................................... 64
■ Solar coverage .......................................................................................................... 65
■ DHW demand of apartments .................................................................................... 65
■ Determining the required solar collector area ........................................................... 65
■ Sizing aid for the Vitodens 242-F .............................................................................. 66
5.7 Intended use ................................................................................................................. 69
6. Control units 6.1 Vitotronic 100, type HC1B, for constant temperature operation ................................... 69
■ Structure and functions ............................................................................................. 69
■ Specification Vitotronic 100, type HC1B ................................................................... 70
6.2 Vitotronic 200, type HO2B, for weather-compensated operation ................................. 71
■ Structure and functions ............................................................................................. 71
■ Specification Vitotronic 200, type HO2B ................................................................... 73
■ Solar control module, type SM1 ................................................................................ 73
Index
2VIESMANN VITODENS
5822 431 GB

6.3 Vitotronic accessories ................................................................................................... 74
■ Allocation to control unit types .................................................................................. 74
■ Vitotrol 100, type UTA ............................................................................................... 74
■ Vitotrol 100, type UTDB ............................................................................................ 75
■ External H4 extension ............................................................................................... 75
■ Vitotrol 100, type UTDB-RF ...................................................................................... 76
■ Notes regarding room temperature hook-up (RS function) for remote control units . 76
■ Information on the Vitotrol 200-A and Vitotrol 300-A ................................................ 76
■ Vitotrol 200-A ............................................................................................................ 77
■ Vitotrol 300-A ............................................................................................................ 77
■ Information on the Vitotrol 200-RF and Vitotrol 300-RF ............................................ 78
■ Vitotrol 200 RF .......................................................................................................... 78
■ Vitotrol 300-RF with table-top dock ........................................................................... 78
■ Vitotrol 300-RF with wall mounting bracket ............................................................... 79
■ Vitocomfort 200 ......................................................................................................... 80
■ Wireless base station ................................................................................................ 80
■ Wireless outside temperature sensor ....................................................................... 81
■ Wireless repeater ...................................................................................................... 81
■ Room temperature sensor ........................................................................................ 82
■ Immersion temperature sensor ................................................................................. 82
■ Immersion temperature sensor ................................................................................. 82
■ Mounting base for programming unit ........................................................................ 83
■ Radio clock receiver .................................................................................................. 83
■ KM BUS distributor ................................................................................................... 83
■ Mixer extension kit with integral mixer motor ............................................................ 83
■ Mixer extension kit for separate mixer motor ............................................................ 84
■ Immersion thermostat ............................................................................................... 85
■ Contact thermostat .................................................................................................... 85
■ Internal H1 extension ................................................................................................ 85
■ Internal H2 extension ................................................................................................ 86
■ AM1 extension .......................................................................................................... 86
■ EA1 extension ........................................................................................................... 87
■ LON connecting cable for data exchange between control units .............................. 87
■ Extension of the connecting cable ............................................................................ 88
■ Terminator (2 pce) ..................................................................................................... 88
■ LON communication module ..................................................................................... 88
■ Vitoconnect 100, type OPTO1 .................................................................................. 88
7. Appendix 7.1 Regulations / Directives ................................................................................................ 89
■ Regulations and directives ........................................................................................ 89
8. Keyword index ............................................................................................................................................ 90
Index (cont.)
VITODENS VIESMANN 3
5822 431 GB

1.1 Product description
AInox-Radial heat exchanger made from stainless steel – for high
operational reliability, a long service life and high heating output
on a very small footprint
BModulating MatriX cylinder burner with intelligent Lambda Pro
Control Plus combustion controller for clean combustion and
quiet operation
CIntegral diaphragm expansion vessel
DDigital boiler control unit
EIntegral variable speed high efficiency circulation pump
FDHW loading cylinder
The Vitodens 222-F gas condensing storage combi boiler is
designed specifically for heating system modernisation projects and
as a replacement for older gas boilers with cylinders installed below.
With an output of up to 35 kW, this heating centre is designed for
high DHW convenience.
The integral loading cylinder with 100 l capacity (up to 26 kW) or
130 l capacity (35 kW) offers the DHW convenience of a separate
DHW cylinder approximately twice the size.
As with all Viessmann storage combi boilers, the Vitodens 222-F gas
condensing boiler requires very little space: Width and depth corre-
spond to standard kitchen unit dimensions. The proven MatriX cylin-
der burner with Lambda Pro Control Plus combustion controller auto-
matically adjusts to varying gas qualities and ensures a constantly
high standard seasonal efficiency [to DIN] of 98 % (Hs) [gross cv].
Recommended applications
■ Installation in detached and terraced houses
■ New build (e.g. pre-fabricated houses and developer projects):
Installation in utility rooms and attics
■ Modernisation: Replacement of gas system boilers, floorstanding
atmospheric gas boilers and oil/gas boilers with DHW cylinders
installed below.
Benefits at a glance
■ Standard seasonal efficiency [to DIN]: up to 98 % (Hs) [gross cv] /
109 % (Hi) [net cv]
■ Durable and efficient thanks to the Inox-Radial heat exchanger
■ Modulating MatriX cylinder burner with a long service life thanks to
stainless steel MatriX gauze
– Tolerant to high temperature loads
– Modulation range up to 01:19 (35 kW)
■ High DHW convenience through enamelled loading cylinder with
100 l capacity (35 kW: 130 l capacity)
■ Power saving, high efficiency circulation pump
■ New, innovative operating concept using colour touchscreen with
plain text and graphic display, commissioning assistant and dis-
plays for energy consumption, as well as alternative operation
from a mobile end device
■ Web-enabled thanks to Vitoconnect (accessories) for operation
and service via Viessmann apps
■ Lambda Pro Control Plus combustion controller for all gas types –
saves on costs by extending the inspection interval to 3 years [in
Germany]
■ Automatic flue gas route adaptation
■ No lateral service clearance required
■ Assembly kit (accessories) with the dimensions and design of the
appliance, for the connection of one regulated and one unregula-
ted heating circuit
Factory setting
Gas condensing boiler with Inox-Radial stainless steel heat
exchanger, modulating MatriX cylinder burner for natural gas and
LPG to DVGW Code of Practice G260 [Germany], expansion vessel,
variable speed high efficiency circulation pump and integral DHW
loading cylinder. Fully plumbed and wired.
Vitodens 222-F, type B2TB
4VIESMANN VITODENS
1
5822 431 GB

White epoxy-coated casing.
Packed separately:
Vitotronic 100 for constant temperature operation
or
Vitotronic 200 for weather-compensated operation.
Preset for operation with natural gas. Conversion within gas groups
E/LL is not required. The conversion to LPG is made at the control
unit (a conversion kit is not required).
Accessories required (order separately)
Installation on finished walls
■ Connection set for installation on finished walls, for upward con-
nection
or
■ Connection set with pre-mounting bracket for installation on fin-
ished walls, for upward connection
or
■ Connection set for installation on finished walls, for connection to
the left or right
or
■ Connection set with pre-mounting bracket for installation on fin-
ished walls, for connection to the left or right
or
■ Connection set with pre-mounting bracket for installation on fin-
ished walls, for downward connection
or
■ Assembly kit with mixer
Installation on unfinished walls
■ Connection set for unfinished walls
or
■ Assembly kit with mixer
Tested quality
CE designation according to current EC Directives
ÖVGW Quality Mark for gas and water equipment
Meets the requirements for the "Blue Angel" eco-label RAL UZ 61.
Vitodens 222-F, type B2TB (cont.)
VITODENS VIESMANN 5
5822 431 GB
1

1.2 Specification
Gas boiler, type B and C, category II2N3P
Rated heating output range (to EN 15502-1) Values in ( ) when operating with LPG P
TF/TR = 50/30 °C kW 1.9 - 13.0 1.9 - 19.0 2.6 - 26.0 1.8 (3.5) - 35.0
TF/TR = 80/60 °C kW 1.7 - 12.1 1.7 - 17.6 2.4 - 24.1 1.6 (3.2) - 32.5
Rated heating output for DHW heating kW 1.7 - 17.2 1.7 - 17.2 2.4 - 29.3 1.6 (3.2) - 33.5
Rated heat input kW 1.8 - 17.9 1.8 - 17.9 2.5 - 30.5 1.7 (3.3) - 34.9
Product ID CE-0085CN0050
IP rating IP X4 to EN 60529
Gas supply pressure
Natural gas mbar 20 20 20 20
kPa 2 2 2 2
LPG mbar 50 50 50 50
kPa 5 5 5 5
Max. permissible gas supply pressure*1
Natural gas mbar 25.0 25.0 25.0 25.0
kPa 2.5 2.5 2.5 2.5
LPG mbar 57.5 57.5 57.5 57.5
kPa 5.75 5.75 5.75 5.75
Sound power level
(to EN ISO 15036-1)
– At partial load dB(A) 35 35 40 37
– At rated heating output (DHW heating) dB(A) 39 41 48 52
Power consumption
– In the delivered condition W 28 42 65 95
– Max. W 126 126 148 163
Weight kg 129 129 132 141
Heat exchanger capacity l 1.8 1.8 2.4 2.8
Max. flow temperature °C 74 74 74 74
Max. flow rate
(Limit for the use of hydraulic separation)
l/h 1200 1200 1400 1600
Nominal circulating water volume
At TF/TR = 80/60 °C
l/h 507 739 1018 1361
Expansion vessel
Capacity l 12 12 12 12
Pre-charge pressure bar 0.75 0.75 0.75 0.75
kPa 75 75 75 75
Permiss. operating pressure (heating water
side)
bar 3 3 3 3
MPa 0.3 0.3 0.3 0.3
Connections (with connection accessories)
Boiler flow and return R ¾ ¾ ¾ ¾
Cold water and DHW R ½ ½ ½ ½
DHW circulation R ½ ½ ½ ½
Dimensions
Length mm 595 595 595 595
Width mm 600 600 600 600
Height mm 1425 1425 1425 1625
Gas connection (with connection accessories) R ½ ½ ½ ½
DHW loading cylinder
Capacity l 100 100 100 130
Permiss. operating pressure (DHW side) bar 10 10 10 10
MPa 1 1 1 1
Continuous DHW output kW 17.2 17.2 29.3 33.5
For DHW heating from 10 to 40 °C l/h 493 493 840 960
Performance factor NL1.8 1.8 3.0 4.8
Initial DHW output
For DHW heating from 10 to 40 °C
l/10 min 182 182 230 273
Connection values
Relative to max. load
With gas
Natural gas E m3/h 1.89 1.89 3.23 3.69
Natural gas LL m3/h 2.20 2.20 3.75 4.30
LPG P kg/h 1.40 1.40 2.38 2.73
*1 If the gas supply pressure is higher than the maximum permissible value, install a separate gas pressure governor upstream of the sys-
tem.
Vitodens 222-F, type B2TB (cont.)
6VIESMANN VITODENS
1
5822 431 GB

Gas boiler, type B and C, category II2N3P
Rated heating output range (to EN 15502-1) Values in ( ) when operating with LPG P
TF/TR = 50/30 °C kW 1.9 - 13.0 1.9 - 19.0 2.6 - 26.0 1.8 (3.5) - 35.0
TF/TR = 80/60 °C kW 1.7 - 12.1 1.7 - 17.6 2.4 - 24.1 1.6 (3.2) - 32.5
Flue gas parameters*2
Flue gas category to G 635/G 636 G52/G51 G52/G51 G52/G51 G52/G51
Temperature (at a return temperature of 30 °C)
– At rated heating output °C 45 45 45 45
– At partial load °C 35 35 35 35
Temperature (at a return temperature of 60 °C) °C 68 68 68 70
Mass flow rate
– For natural gas
– At rated heating output (DHW heating) kg/h 31.8 31.8 54.3 62.1
– At partial load kg/h 5.5 5.5 8.7 8.7
– For LPG
– At rated heating output (DHW heating) kg/h 30.2 30.2 51.5 58.9
– At partial load kg/h 7.6 7.6 14.0 14.0
Available draught Pa 250 250 250 250
mbar 2.5 2.5 2.5 2.5
Max. amount of condensate
To DWA-A 251 l/h 2.3 2.5 4.3 4.9
Condensate connection (hose nozzle) Ø mm 20-24 20-24 20-24 20-24
Flue gas connection Ø mm 60 60 60 60
Ventilation air connection Ø mm 100 100 100 100
Standard seasonal efficiency [to DIN] at
TF/TR = 40/30 °C % Up to 98 (Hs) [gross cv] / 109 (Hi) [net cv]
Energy efficiency class
– Heating A A A A
– DHW heating, draw-off profile XL A A A A
*2 Calculation values for sizing the flue system to EN 13384.
Flue gas temperatures as actual gross values at 20 °C combustion air temperature.
The flue gas temperature at a return temperature of 30 °C is significant for the sizing of the flue system.
The flue gas temperature at a return temperature of 60 °C is used to determine the application range of flue pipes with maximum permissi-
ble operating temperatures.
Vitodens 222-F, type B2TB (cont.)
VITODENS VIESMANN 7
5822 431 GB
1

80
e
50
595
50
600
100
569
46
40
50
c
d
a b
140
50
G
C
F
A
B
D
E
G
K
A
B
C
FD
E
AA
AA
AA
G
H
AHeating flow R¾
BDHW R½
CGas connection R½
DCold water R½
EHeating return R¾
FDHW circulation R½ (separate accessory)
GCondensate drain facing backwards into the wall
HCondensate drain to the side
KWiring area
Rated heating output in kW a
mm
b
mm
c
mm
d
mm
e
mm
13 to 19 745 750 1425 1465 201
26 745 750 1425 1465 224
35 945 950 1625 1665 224
Note
The dimensioned drawing shows example fittings for installation on
finished walls, for upward connection and connection to the left/right.
Order the connection sets separately as accessories.
For the dimensions of the individual connection sets, see the design
information.
If using the connection set with pre-mounting bracket for downward
connections on finished walls, maintain a wall clearance of 70 mm.
Note
All height dimensions have a tolerance of +7 mm on account of the
adjustable feet.
Vitodens 222-F, type B2TB (cont.)
8VIESMANN VITODENS
1
5822 431 GB

Variable speed heating circuit pump in the Vitodens 222-F
The integral circulation pump is a highly efficient pump with substan-
tially lower power consumption than conventional pumps.
The pump speed and consequently the pump rate are regulated sub-
ject to the outside temperature and the switching times for heating or
reduced mode. The control unit transmits the current default settings
to the circulation pump via an internal data BUS.
The min. and max. speed and the speed in reduced mode can be
adjusted using codes at the control unit of the existing heating sys-
tem.
In the delivered condition, the minimum pump rate (coding address
"E7") and the maximum pump rate (coding address "E6") are set to
the following values:
Rated heating output in kW Speed settings in the delivered
condition in %
Min. pump rate Max. pump
rate
13 45 60
19 45 65
26 45 80
35 45 90
Note
In conjunction with a low loss header, heating water buffer cylinder
and heating circuits with mixer, the internal circulation pump runs at
a constant speed. The speed can be adjusted subject to demand by
changing the code at the control unit.
Specification circulation pump
Rated heating out-
put
kW 13 19 26 35
Circulation pump Typ
e
UPM3
15-75
UPM3
15-75
UPM3
15-75
UPM3
15-75
Rated voltage V~ 230 230 230 230
Power consumption
– Max. W 60 60 60 60
– Min. W 2 2 2 2
– Factory setting W 12 20 38 45
Energy efficiency class A A A A
Vitodens 222-F, type B2TB (cont.)
VITODENS VIESMANN 9
5822 431 GB
1

Residual head of the integral circulation pump
Residual head
0
kPa
0 100 200 300 400 500 600 700 800 900 1000 1100 1200
Flow rate in l/h
100
200
300
400
0
10
20
30
40
500 50
C
D
E
H
mbar
600 60 500 50
G
F
B
A
HUpper operational limit
Curve Pump rate, circulation
pump
Coding address setting "E6"
A40 % E6:040
B50 % E6:050
C60 % E6:060
D70 % E6:070
E80 % E6:080
F90 % E6:090
G100 % E6:100
Vitodens 222-F, type B2TB (cont.)
10 VIESMANN VITODENS
1
5822 431 GB

2.1 Product description
AInox-Radial heat exchanger made from stainless steel – for high
operational reliability, a long service life and high heating output
on a very small footprint
BModulating MatriX cylinder burner with intelligent Lambda Pro
Control Plus combustion controller for clean combustion and
quiet operation
CIntegral diaphragm expansion vessel
DDigital boiler control unit
EIntegral variable speed high efficiency circulation pump
FDHW cylinder with internal indirect coil
The Vitodens 222-F storage combi boiler combines the benefits of
the Vitodens 200-W with the high level of DHW convenience of a
separate DHW cylinder.
As with all Viessmann storage combi boilers, the Vitodens 222-F gas
condensing boiler requires very little space: Width and depth corre-
spond to standard kitchen unit dimensions. The proven MatriX cylin-
der burner with Lambda Pro Control Plus combustion controller auto-
matically adjusts to varying gas qualities and ensures a constantly
high standard seasonal efficiency [to DIN] of 98 % (Hs) [gross cv].
The Vitodens 222-F, type B2SB with integral 130 l cylinder with inter-
nal indirect coil is particularly suitable for hard water areas.
Due to its smooth surface the internal indirect coil is resistant to lime-
scale deposits.
Recommended applications
■ Installation in detached and terraced houses
■ New build (e.g. pre-fabricated houses and developer projects):
Installation in utility rooms and attics
■ Modernisation: Replacement of gas system boilers, floorstanding
atmospheric gas boilers and oil/gas boilers with DHW cylinders
installed below
■For use in areas with a water hardness of > 20 °dH (3.58 mol/m3)
Benefits at a glance
■ Standard seasonal efficiency [to DIN]: up to 98 % (Hs) [gross cv] /
109 % (Hi) [net cv]
■ Durable and efficient thanks to the Inox-Radial heat exchanger
■ Modulating MatriX cylinder burner with a long service life thanks to
stainless steel MatriX gauze
– Tolerant to high temperature loads
– Modulation range up to 01:10 (26 kW)
■ Enamelled DHW cylinder with internal indirect coil and 130 l
capacity (NL factor up to 1.8)
■ Power saving, high efficiency circulation pump
■ New, innovative operating concept using colour touchscreen with
plain text and graphic display, commissioning assistant and dis-
plays for energy consumption, as well as alternative operation
from a mobile end device
■ Web-enabled thanks to Vitoconnect (accessories) for operation
and service via Viessmann apps
■ Lambda Pro Control Plus combustion controller for all gas types –
saves on costs by extending the inspection interval to 3 years [in
Germany]
■ Automatic flue gas route adaptation
Vitodens 222-F, type B2SB
VITODENS VIESMANN 11
5822 431 GB
2

■ No lateral service clearance required
■ Assembly kit (accessories) with the dimensions and design of the
appliance, for the connection of one regulated and one unregula-
ted heating circuit
Factory setting
Gas condensing boiler with Inox-Radial heat exchanger, modulating
MatriX cylinder burner for natural gas and LPG to DVGW Code of
Practice G260 [Germany], expansion vessel, variable speed high
efficiency circulation pump and integral DHW cylinder. Fully plumbed
and wired.
White epoxy-coated casing.
Packed separately:
Vitotronic 100 for constant temperature operation
or
Vitotronic 200 for weather-compensated operation.
Preset for operation with natural gas. Conversion within gas groups
E/LL is not required. The conversion to LPG is made at the control
unit (a conversion kit is not required).
Accessories required (order separately)
Installation on finished walls
■ Connection set for installation on finished walls, for upward con-
nection
or
■ Connection set with pre-mounting bracket for installation on fin-
ished walls, for upward connection
or
■ Connection set for installation on finished walls, for connection to
the left or right
or
■ Connection set with pre-mounting bracket for installation on fin-
ished walls, for connection to the left or right
or
■ Connection set with pre-mounting bracket for installation on fin-
ished walls, for downward connection
or
■ Assembly kit with mixer
Installation on unfinished walls
■ Connection set for unfinished walls
or
■ Assembly kit with mixer
Tested quality
CE designation according to current EC Directives
ÖVGW Quality Mark for gas and water equipment
Meets the requirements for the "Blue Angel" eco-label RAL UZ 61.
Vitodens 222-F, type B2SB (cont.)
12 VIESMANN VITODENS
2
5822 431 GB

2.2 Specification
Gas boiler, type B and C, category II2N3P
Rated heating output range (to EN 15502-1)
TF/TR = 50/30 °C kW 1.9 - 13.0 1.9 - 19.0 2.6 - 26.0
TF/TR = 80/60 °C kW 1.7 - 12.1 1.7 - 17.6 2.4 - 24.1
Rated heating output for DHW heating kW 1.7 - 17.2 1.7 - 17.2 2.4 - 23.7
Rated heat input kW 1.8 - 17.9 1.8 - 17.9 2.5 - 24.7
Product ID CE-0085CN0050
IP rating IP X4 to EN 60529
Gas supply pressure
Natural gas mbar 20 20 20
kPa 2 2 2
LPG mbar 50 50 50
kPa 5 5 5
Max. permissible gas supply pressure*3
Natural gas mbar 25.0 25.0 25.0
2.5 2.5 2.5
LPG mbar 57.5 57.5 57.5
5.75 5.75 5.75
Sound power level
(to EN ISO 15036-1)
– At partial load dB(A) 33 33 42
– At rated heating output (DHW heating) dB(A) 39 41 48
Power consumption
– In the delivered condition W 28 42 65
– Max. W 86 86 95
Weight kg 139 139 142
Heat exchanger capacity l 1.8 1.8 2.4
Max. flow temperature °C 74 74 74
Max. flow rate
(Limit for the use of hydraulic separation)
l/h 1200 1200 1400
Nominal circulating water volume
At TF/TR = 80/60 °C
l/h 537 739 1018
Expansion vessel
Capacity l 12 12 12
Pre-charge pressure bar 0.75 0.75 0.75
kPa 75 75 75
Permiss. operating pressure (heating water side) bar 3 3 3
MPa 0.3 0.3 0.3
Connections (with connection accessories)
Boiler flow and return R ½ ¾ ¾
Cold water and DHW R ½ ½ ½
DHW circulation R ½ ½ ½
Dimensions
Length mm 595 595 595
Width mm 600 600 600
Height mm 1625 1625 1625
Gas connection (with connection accessories) R ½ ½ ½
DHW cylinder
Capacity l 130 130 130
Permiss. operating pressure (DHW side) bar 10 10 10
MPa 1 1 1
Continuous DHW output kW 17.2 17.2 23.7
For DHW heating from 10 to 40 °C l/h 493 493 680
Performance factor NL*4 1.3 1.3 1.8
Initial DHW output
For DHW heating from 10 to 40 °C
l/10 min 153 153 182
Connection values
Relative to max. load
With gas
Natural gas E m3/h 1.89 1.89 2.61
Natural gas LL m3/h 2.06 2.20 3.04
LPG P kg/h 1.31 1.40 1.93
*3 If the gas supply pressure is higher than the maximum permissible value, install a separate gas pressure governor upstream of the sys-
tem.
*4 At 70 °C average boiler water temperature and cylinder storage temperature Tcyl = 60 °C.
DHW performance factor NL depends on cylinder storage temperature Tcyl.
Standard values: Tcyl = 60 °C → 1.0 × NL Tcyl = 55 °C → 0.75 × NL Tcyl = 50 °C → 0.55 × NL Tcyl = 45 °C → 0.3 × NL.
Vitodens 222-F, type B2SB (cont.)
VITODENS VIESMANN 13
5822 431 GB
2

Gas boiler, type B and C, category II2N3P
Rated heating output range (to EN 15502-1)
TF/TR = 50/30 °C kW 1.9 - 13.0 1.9 - 19.0 2.6 - 26.0
TF/TR = 80/60 °C kW 1.7 - 12.1 1.7 - 17.6 2.4 - 24.1
Flue gas parameters*2
Flue gas category to G 635/G 636 G52/G51 G52/G51 G52/G51
Temperature (at 30 °C return temperature)
– At rated heating output °C 45 45 45
– At partial load °C 35 35 35
Temperature (at a return temperature of 60 °C) °C 68 68 70
Mass flow rate
– For natural gas
– At rated heating output kg/h 31.8 31.8 43.9
– At partial load kg/h 5.5 5.5 8.7
– For LPG
– At rated heating output kg/h 30.2 30.2 41.7
– At partial load kg/h 7.6 7.6 14.0
Available draught Pa 250 250 250
mbar 2.5 2.5 2.5
Max. amount of condensate
To DWA-A 251 l/h 2.3 2.5 3.5
Condensate connection (hose nozzle) Ø mm 20-24 20-24 20-24
Flue gas connection Ø mm 60 60 60
Ventilation air connection Ø mm 100 100 100
Standard seasonal efficiency [to DIN] at
TF/TR = 40/30 °C % Up to 98 (Hs) [gross cv] / 109 (Hi) [net cv]
Energy efficiency class
– Heating A A A
– DHW heating, draw-off profile XL A A A
*2 Calculation values for sizing the flue system to EN 13384.
Flue gas temperatures as actual gross values at 20 °C combustion air temperature.
The flue gas temperature at a return temperature of 30 °C is significant for the sizing of the flue system.
The flue gas temperature at a return temperature of 60 °C is used to determine the application range of flue pipes with maximum permissi-
ble operating temperatures.
Vitodens 222-F, type B2SB (cont.)
14 VIESMANN VITODENS
2
5822 431 GB

100
569
46
40
50
1625
1685
945
80
140
50
A
C
D
F
E
B
E
F
BA
D
C
K
G
H
G
G
C
A
B
F
D
E
a
50
595
50
600
AHeating flow R¾
BDHW R½
CGas connection R½
DCold water R½
EHeating return R¾
FDHW circulation R½ (separate accessory)
GCondensate drain facing backwards into the wall
HCondensate drain to the side
KWiring area
Rated heating output
kW
a
mm
13 and 19 201
26 224
Note
The dimensioned drawing shows example fittings for installation on
finished walls, for upward connection and connection to the left/right.
Order the connection sets separately as accessories.
For the dimensions of the individual connection sets, see the design
information.
If using the connection set with pre-mounting bracket for downward
connections on finished walls, maintain a wall clearance of 70 mm.
Note
All height dimensions have a tolerance of +7 mm on account of the
adjustable feet.
Vitodens 222-F, type B2SB (cont.)
VITODENS VIESMANN 15
5822 431 GB
2

Variable speed heating circuit pump in the Vitodens 222-F
The integral circulation pump is a highly efficient pump with substan-
tially lower power consumption than conventional pumps.
The pump speed and consequently the pump rate are regulated sub-
ject to the outside temperature and the switching times for heating or
reduced mode. The control unit transmits the current default settings
to the circulation pump via an internal data BUS.
The min. and max. speed and the speed in reduced mode can be
adjusted using codes at the control unit of the existing heating sys-
tem.
In the delivered condition, the minimum pump rate (coding address
"E7") and the maximum pump rate (coding address "E6") are set to
the following values:
Rated heating output in kW Speed settings in the delivered
condition in %
Min. pump rate Max. pump
rate
13 45 60
19 45 65
26 45 80
Note
In conjunction with a low loss header, heating water buffer cylinder
and heating circuits with mixer, the internal circulation pump runs at
a constant speed. The speed can be adjusted subject to demand by
changing the code at the control unit.
Specification circulation pump
Rated heating output kW 13 19 26
Circulation pump Type UPM3
15-75
UPM3
15-75
UPM3
15-75
Rated voltage V~ 230 230 230
Power consumption
– Max. W 60 60 60
– Min. W 2 2 2
– Factory setting W 12 20 38
Energy efficiency class A A A
Vitodens 222-F, type B2SB (cont.)
16 VIESMANN VITODENS
2
5822 431 GB

Residual head of the integral circulation pump
Residual head
0
kPa
0 100 200 300 400 500 600 700 800 900 1000 1100 1200
Flow rate in l/h
100
200
300
400
0
10
20
30
40
500 50
C
D
E
H
mbar
600 60 500 50
G
F
B
A
HUpper operational limit
Curve Pump rate, circulation
pump
Coding address setting "E6"
A40 % E6:040
B50 % E6:050
C60 % E6:060
D70 % E6:070
E80 % E6:080
F90 % E6:090
G100 % E6:100
Vitodens 222-F, type B2SB (cont.)
VITODENS VIESMANN 17
5822 431 GB
2

3.1 Product description
AInox-Radial heat exchanger made from stainless steel – for high
operational reliability, a long service life and high heating output
on a very small footprint
BModulating MatriX gas burner for extremely clean combustion
CIntegral diaphragm expansion vessel
DDigital boiler control unit
EIntegral solar circuit pump
FDual mode DHW cylinder
The Vitodens 242-F gas condensing storage combi boiler for instal-
lation against the wall is affordable, compact, efficient and solar-
compatible. This storage combi boiler is factory-prepared for direct
connection of a solar thermal system. The solar control module is
already integrated and is regulated via the Vitotronic control unit.
The 170 l dual mode DHW cylinder provides a high level of DHW
convenience. For ease of handling the Vitodens 242-F can be trans-
ported in two parts.
Recommended applications
■ Installation in detached and terraced houses
■ New build (e.g. pre-fabricated houses and developer projects):
Installation in utility rooms
Benefits at a glance
■ Gas condensing storage combi boiler with integral solar cylinder
■ Standard seasonal efficiency [to DIN]: up to 98 % (Hs) [gross cv] /
109 % (Hi) [net cv]
■ Durable and efficient thanks to the Inox-Radial stainless steel heat
exchanger
■ MatriX cylinder burner with Lambda Pro Control Plus combustion
controller for permanently high efficiency and clean combustion
– Modulation range up to 1:10
■ Power saving, high efficiency circulation pumps for heating circuit
and solar circuit
■ Enamelled dual mode loading cylinder with 170 l capacity
■ New, innovative operating concept using colour touchscreen with
plain text and graphic display, commissioning assistant and dis-
plays for energy consumption, as well as alternative operation
from a mobile end device
Vitodens 242-F, type B2UB
18 VIESMANN VITODENS
3
5822 431 GB

■ Web-enabled thanks to Vitoconnect (accessories) for operation
and service via Viessmann apps
■ Automatic flue gas route adaptation
■ Can be split for easier handling
■ Solar coverage > 50 %
■ Assembly kit (accessories) with the dimensions and design of the
appliance, for the connection of one regulated and one unregula-
ted heating circuit
Factory setting
Gas condensing boiler with Inox-Radial heat exchanger, MatriX cyl-
inder burner for natural gas and LPG to DVGW Code of Practice
G260 [Germany], expansion vessel, variable speed heating circuit
pump and solar circuit pump, heat transfer medium drip pan, solar
side safety valve, Vitotronic 200 for weather-compensated operation,
solar control module and integral DHW solar cylinder. Fully plumbed
and wired. White epoxy-coated casing.
Preset for operation with natural gas. Conversion within gas groups
E/LL is not required. The conversion to LPG is made at the control
unit (a conversion kit is not required).
Accessories required (order separately)
Installation on finished walls
■ Connection set for installation on finished walls, for upward con-
nection
or
■ Connection set with pre-mounting bracket for installation on fin-
ished walls, for upward connection
or
■ Connection set for installation on finished walls, for connection to
the left or right
or
■ Connection set with pre-mounting bracket for installation on fin-
ished walls, for connection to the left or right
or
■ Assembly kit with mixer
Installation on unfinished walls
■ Connection set for unfinished walls
or
■ Assembly kit with mixer
Tested quality
CE designation according to current EC Directives
ÖVGW Quality Mark for gas and water equipment
Meets the requirements for the "Blue Angel" eco-label RAL UZ 61.
Vitodens 242-F, type B2UB (cont.)
VITODENS VIESMANN 19
5822 431 GB
3

3.2 Specification
Gas boiler, type B and C, category II2N3P
Rated heating output range (to EN 15502-1)
TF/TR = 50/30 °C kW 1.9 - 13.0 1.9 - 19.0 2.6 - 26.0
TF/TR = 80/60 °C kW 1.7 - 12.1 1.7 - 17.6 2.4 - 24.1
Rated heating output for DHW heating kW 1.7 - 17.2 1.7 - 17.2 2.4 - 29.3
Rated heat input kW 1.8 - 17.9 1.8 - 17.9 2.5 - 30.5
Product ID CE-0085CN0050
IP rating IP X4 to EN 60529
Gas supply pressure
Natural gas mbar 20 20 20
kPa 2 2 2
LPG mbar 50 50 50
kPa 5 5 5
Max. permissible gas supply pressure*5
Natural gas mbar 25.0 25.0 25.0
kPa 2.5 2.5 2.5
LPG mbar 57.5 57.5 57.5
kPa 5.75 5.75 5.75
Sound power level
(to EN ISO 15036-1)
– At partial load dB(A) 33 33 35
– At rated heating output (DHW heating) dB(A) 39 41 48
Power consumption
– In the delivered condition W 28 42 65
– Max. W 181 181 203
Weight
– Total (with casing) kg 161 161 165
– Heat cell module kg 42 42 46
– Cylinder module kg 95 95 95
Heat exchanger capacity l 1.8 1.8 2.4
Solar circuit capacity l 9.9 9.9 9.9
Max. flow temperature °C 74 74 74
Max. flow rate
(Limit for the use of hydraulic separation)
l/h 1200 1200 1400
Nominal circulating water volume
At TF/TR = 80/60 °C
l/h 507 739 1018
Expansion vessel
Capacity l 12 12 12
Pre-charge pressure bar 0.75 0.75 0.75
kPa 75 75 75
Permiss. operating pressure
– Heating circuit bar 3 3 3
MPa 0.3 0.3 0.3
– Solar circuit bar 6 6 6
MPa 0.6 0.6 0.6
Connections (with connection accessories)
Boiler flow and return R ¾ ¾ ¾
Solar flow and return R/Ø mm ¾/22 ¾/22 ¾/22
Cold water and DHW R ½ ½ ½
DHW circulation R ½ ½ ½
Dimensions
Length mm 595 595 595
Width mm 600 600 600
Height mm 1875 1875 1875
Height when tilted mm 2000 2000 2000
Gas connection (with connection accessories) R ½ ½ ½
*5 If the gas supply pressure is higher than the maximum permissible value, install a separate gas pressure governor upstream of the sys-
tem.
Vitodens 242-F, type B2UB (cont.)
20 VIESMANN VITODENS
3
5822 431 GB