View Tech 4-port PoE Switch with 1 Uplink Port User manual

Pleasefollowthe belowinstallationsteps
Pleasecheckthefollowingitems before installation, if it is missing, please contact the
dealer.
4 ports PoE Ethernet switch 1pc
Poweradaptor1pc
AC power cable1pc
Accessory1set
Usermanual 1set
1) Please turn off the signal power and display device power before installation,
installation with power will damage the transmission equipment.
2) Use network cable connect PoE IP camera and 1〜4 down link ports of
product respectively.
3) Useanetworkcable connect equipment uplink port and NVR or computer.
4) Turnonthepower of the equipment.
5) Check if the installation is correct, equipment is in good condition, the connection
is stable, then provide power for system.
6) EnsuretheEthernetequipmentwithpowerandworkproperly.
Installationsteps
10/100MbpsSwitchwith4-PortPoE
This Product is an unmanaged PoE switch, provides 4*10/100Base-TX PoE ports +
1/2*10/100Base-TX RJ45 ports. Max PoE power output for single port is 30W, the total PoE
power budget is 60W. Providing three operating modes (Default, V LA N, CCTV). The switch
supports PoE watchdog under VLAN and CCT V mode. It improves the online rate of
cameras.
Board Diagram
Frontboardof4-portPoESwitchwith1UplinkPort
4*10/100Base-TX Ethernet ports (PoE ports) and 1/2*10/100Base-TX uplink port.
Support IEEE802.3af/at standards, Max.30W output of single port.
Three operating mode:
Default: All ports can be communicated freely.
VL AN: Port 1-4 are isolated respectively, but can communicate with uplink ports, support
PoE watchdog.
CC TV: The transmission distance can be extended to 250 meter, while link speed of
downlink ports 1~4 will be limited to 10Mbps(Uplink ports keep 100Mbps). Support PoE
watchdog.
6KV surge protection, 8KV E SD immunity and anti-interference.
Easy & safe installation: wall-mounting, desktop.
Plug-and-play.
Application
Thetransmissiondistanceisrelated to theconnectedcable.Wesuggeststandard
Cat5e/6 network cable, so the transmission distance can up to100m!
Theequipment must connect the ground according to the request.
Description:
4 Ports PoE Ethernet Switch
Cat5/5e/6 network cable
LCD
NVR
PoE PTZ Camera
power
10/100MbpsSwitchwith4-PortPoE
UserManual
6
Power Input Port PoE Downlink Ethernet Port Uplink Ethernet Port
DIP switch
Power Input Port PoE Downlink Ethernet Port Uplink Ethernet Port
Feature
12
Notice
PoE IP Camera
PoE Dome Camera
PoE IP Camera
Grounding
Grounding
13.238.101.1758
V2.0
UserManual
Frontboardof4-portPoESwitchwith2UplinkPorts

Instruments to be used: wire crimper, network tester. Wire sequence of R J45 plug should
conform with EIA/TIA568A or 568B.
1) Please remove 2cm long the insulating layer, and bare 4 pairs UTP cable.
2) Separate the 4 pairs UTP cable and straighten them.
3) Line up the 8 pieces of cables per EIA/TIA 568A or 568B.
4) Cut off the cables to leave 1.5cm bare wire.
5) Plug 8 cables into RJ45 plug, make sure each cable is in each pin.
6) Use the wire crimper to crimp it.
7) Repeat above 5 steps to make the another end.
8) Use network tester to test the cable if it works.
PlugProducingMethod
PinColor
White/Green
Green
Blue
White/Orange
White/Blue
White/Brown
Orange
Brown
1
2
3
4
5
6
7
8
PinColor
1
2
3
4
5
6
7
8
White/Green
Green
Blue
White/Orange
White/Blue
White/Brown
Orange
Brown
EIA/TIA568A EIA/TIA568B
When choose RJ45 make sure if one end is EIA/TI A568A,the other end should also be
EI A/T IA568A.
When choose RJ45 make sure if one end is EIA/TI A568B,the other end should also be
EI A/T IA568B.
Notice
Make sure the equipment is installed according to the manufactures installation guide.
Confirm RJ45 cable order meets EIA/TI A568A or 568B standard.
Every PoE port can provide PoE equipment maximum power less than 30W, please do
not connect the PoE equipment with power over 30W.
Replace the equipment with a proper functioning 4 ports PoE Ethernet Switch to check
if the equipment is damaged.
Please contact your vendor if trouble still exists.
Model
4-port PoE Switch with 1 Uplink
Port
4-port PoE Switch with 2 Uplink
Ports
Downlink Ports
4*10/100Base-TX (PoE)
Uplink Ports
1* 10/100Base-TX RJ45
2*10/100Base-TX RJ45
Standards
IE EE 802.3/802.3u/IEEE802.3x
Switching Capacity
1Gbps
1.2Gbps
Packet Forwarding Rate
0.75Mpps
0.89Mpps
Forwarding Modes
Srore&Foward
Packet Buffer
448kbits
MACTable
1k
PoE Standard
802.3af/at(PSE)
PoEPowerSupply Type
End-span
PoE Pin Assignment
1/2(+),3/6(-)
PoE Output
Single PoE Output≤30W(52V DC), Whole machine PoE
output≤60W
Three Working Modes
1. Default: All ports can be communicated freely.
2.VLAN: Port 1-4 are isolated respectively, but can
communicate with uplink ports, support PoE watchdog.
3.CCTV: The transmission distance can be extended to 250
meter, while link speed of downlink ports 1~4 will be limited to
10Mbps(Uplink ports keep 100Mbps). Support PoE watchdog.
SurgeImmunity
Common mode 6KV,Execute standard: IEC61000-4-5
ESD Protection
Contact discharge 6K, Air discharge 8KV,
Execute standard: IEC61000-4-2
InputVoltage
DC 52V 1.2A
Power Consumption
<63W
Operating Temperature
-10℃~50℃
StorageTemperature
-40℃~85℃
OperatingHumidity
5%~95%(Non-condensing)
Dimensions (W * D * H)
122mm*92mm*25mm
Material
Metal
Weight
343g
连接接口
Specification change will not be noticed
连接接口
Specification TroubleShooting
Pleasefollow the steps if the equipment has trouble.
10/100MbpsSwitchwith4-PortPoE
34
10/100MbpsSwitchwith4-PortPoE
This manual suits for next models
1
Popular Switch manuals by other brands

H3C
H3C S5560S-EI Series installation guide

Lantech
Lantech IES-3 Series user manual

Siemens
Siemens VBFS321F installation instructions

Sunricher
Sunricher SR-ZGP2801K2-DIM instruction manual

MS Electronics
MS Electronics TDS3 Product guide

Transition Networks
Transition Networks SESPM1040-541-LT Series quick start guide