ViewSonic CDP4260-TL User manual

CDP4260-TL/CDP5560-TL
LCD Monitor
User Guide
Model No.:VS15795/VS15796
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://
ZZZYLHZVRQLFFRPLQ(QJOLVKRULQVSHFL¿FODQJXDJHVXVLQJWKH5HJLRQDOVHOHFWLRQ
box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”

i
Compliance Information
NOTE: This section addresses all connected requirements and statements regarding regulations.
Confirmed corresponding applications shall refer to nameplate labels and relevant markings on
unit.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A/
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his/her own
expense.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: To comply with the limits for the Class A/Class B digital device, pursuant to Part 15 of
the FCC Rules, this device must be installed in computer equipment certified to comply with the
Class A/Class B limits. All cables used to connect the computer and peripherals must be shielded
and grounded. Operation with non-certified computers or non-shielded cables may result in
interference to radio or television reception. Changes and modifications not expressly approved by
the manufacturer could void the user’s authority to operate this equipment.
For Canada
CAN ICES-3 (A/B)/NMB-3(A/B)

ii
CE Conformity for European Countries
The device complies with the EMC Directive 2004/108/EC and Low Voltage Directive
2006/95/EC.
Following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical and Electronic
Equipment Directive 2012/19/EC (WEEE).
The mark indicates the requirement NOT to dispose of the equipment as unsorted
municipal waste, but use the return and collection systems according to local law.
If the batteries, accumulators and button cells included with this equipment, display the
chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content
of more than 0.0005% Mercury or more than, 0.002% Cadmium, or more than 0.004%
Lead.
Industry Canada Notice
This device complies with Canadian RSS-210.To prevent radio interference to the licensed service,
this device is intended to be operated indoors and away from windows to provide maximum
shielding. Equipment (or its transmitting antenna) that is installed outdoors is subject to licensing.
The installer of this radio equipment must ensure that the antenna is located or pointed such that it
does not emit RF field in excess of Health Canada limits for the general population; consult Safety
Code 6, obtainable from Health Canada’s website www.hc-sc.gc.ca/rpb.
R&TTE Compliance Statement
This device complies with the Essential Requirements of the R&TTE Directive of the European
Union (1999/5/EC). This equipment meets the following conformance standards:
ETSI EN 300 328
EN 301 489-01
EN 301 489-17
EN 62311
Notified Countries: Germany, UK, Netherlands, Belgium, Sweden, Denmark,
Finland, France, Italy, Spain, Austria, Ireland, Portugal, Greece, Luxembourg,
Estonia, Latvia, Lithuania, Czech Republic, Slovakia, Slovenia, Hungary, Poland and Malta.

iii
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive 2011/65/EU of the
European Parliament and the Council on restriction of the use of certain hazardous substances in
electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum
concentration values issued by the European Technical Adaptation Committee (TAC) as shown
below:
Substance
Proposed Maximum
Concentration
Actual Concentration
Lead (Pb) 0,1% < 0,1%
Mercury (Hg) 0,1% < 0,1%
Cadmium (Cd) 0,01% < 0,01%
Hexavalent Chromium (Cr6+) 0,1% < 0,1%
Polybrominated biphenyls (PBB) 0,1% < 0,1%
Polybrominated diphenyl ethers (PBDE) 0,1% < 0,1%
Certain components of products as stated above are exempted under the Annex III of the RoHS2
Directives as noted below:
Examples of exempted components are:
1. 0HUFXU\LQFROGFDWKRGHÀXRUHVFHQWODPSVDQGH[WHUQDOHOHFWURGHÀXRUHVFHQWODPSV&&)/DQG
EEFL) for special purposes not exceeding (per lamp):
(1) Short length (≦500 mm): maximum 3.5 mg per lamp.
(2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.
(3) Long length (＞1,500 mm): maximum 13 mg per lamp.
2. Lead in glass of cathode ray tubes.
3. /HDGLQJODVVRIÀXRUHVFHQWWXEHVQRWH[FHHGLQJE\ZHLJKW
4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.
5. Copper alloy containing up to 4% lead by weight.
6. Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight
or more lead).
7. Electrical and electronic components containing lead in a glass or ceramic other than dielectric
ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound.

iv
Safety Precautions
FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND
USING THE LCD COLOR MONITOR:
• DO NOT REMOVE MONITOR BACK COVER. There are no user serviceable parts inside and
opening or removing covers may expose you to dangerous shock hazards or other risks. Refer
DOOVHUYLFLQJWRTXDOL¿HGVHUYLFHSHUVRQQHO
• Do not spill any liquids into the cabinet or use your monitor near water.
• Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage
SRLQWVZKLFKFDQEHKDUPIXORUIDWDORUPD\FDXVHHOHFWULFVKRFN¿UHRUHTXLSPHQWIDLOXUH
• Do not place any heavy objects on the power cord. Damage to the cord may cause shock or
¿UH
• Do not place this product on a sloping or unstable cart, stand or table, as the monitor may fall,
causing serious damage to the monitor.
• Do not place any objects onto the monitor and do not use the monitor outdoors.
• 7KHLQVLGHRIWKHÀXRUHVFHQWWXEHORFDWHGZLWKLQWKH/&'PRQLWRUFRQWDLQVPHUFXU\3OHDVH
follow the laws or rules of your municipality to dispose of the tube properly.
• Do not bend power cord.
• Do not use monitor in high temperature, humid, dusty, or oily areas.
• If monitor or glass is broken, do not come in contact with the liquid crystal and handle with
care.
• Allow adequate ventilation around the monitor, so that heat can properly dissipate. Do not
block ventilated openings or place the monitor near a radiator or other heat sources. Do not
put anything on top of the monitor.
• The power cable connector is the primary means of detaching the system from the power
supply. The monitor should be installed close to a power outlet, which is easily accessible.
• Handle with care when transporting. Save packaging for transporting.
• Please clean the holes of back cabinet to reject dirt and dust at least once a year because of
set reliability.
• If using the cooling fan continuously, it’s recommended to wipe holes a minimum of once a
month.
• When installing the remote control batteries;
- Align the batteries according to the (+) and (-) indications inside the case.
$OLJQWKHLQGLFDWLRQRIWKHEDWWHU\¿UVWLQVLGHWKHFDVH

v
CAUTION:
Immediately unplug your monitor from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled, or objects have fallen into the monitor.
• If the monitor has been exposed to rain or water.
• If the monitor has been dropped or the cabinet damaged.
• If the monitor does not operate normally by following operating instructions.
Recommended Use
CAUTION:
• For optimum performance, allow 20 minutes for warm-up.
• Rest your eyes periodically by focusing on an object at least 5 feet away. Blink often.
• Position the monitor at a 90° angle to windows and other light sources to minimize glare and
UHÀHFWLRQV
• Clean the LCD monitor surface with a lint-free, nonabrasive cloth. Avoid using any cleaning
solution or glass cleaner!
• Adjust the monitor’s brightness, contrast and sharpness controls to enhance readability.
• $YRLGGLVSOD\LQJ¿[HGSDWWHUQVRQWKHPRQLWRUIRUORQJSHULRGVRIWLPHWRDYRLGLPDJH
persistence (after image effects).
• Get regular eye checkups.
Ergonomics
To realize the maximum ergonomic benefits, we recommend the following:
• Use the preset Size and Position controls with standard signals.
• Use the preset Color Setting.
• Use non-interlaced signals.
• 'RQRWXVHSULPDU\FRORUEOXHRQDGDUNEDFNJURXQGDVLWLVGLI¿FXOWWRVHHDQGPD\SURGXFH
H\HIDWLJXHGXHWRLQVXI¿FLHQWFRQWUDVW

vi
Table Of Contents
4. OSD Menu............................................ 13
4.1. Navigating the OSD Menu .......... 13
4.1.1. Navigating the OSD menu
using the remote control .... 13
4.1.2. Navigating the OSD menu
using the display’s control
buttons ............................... 13
4.2. OSD Menu Overview ................... 13
4.2.1. PICTURE menu ................. 13
4.2.2. SCREEN menu.................. 14
4.2.3. AUDIO menu...................... 15
4.2.4. PIP menu ........................... 16
4.2.5. CONFIGURATION1 menu . 16
4.2.6. CONFIGURATION2 menu . 18
4.2.7. CONFIGURATION3 menu . 19
4.2.8. ADVANCED OPTION
menu.................................. 20
5. Commercial Display LAN Control ..... 22
5.1. OSD Menu Setup for Network
Connection................................... 22
5.2. Before Using Web Browser
Control.......................................... 22
5.3. Access from Web Browser........... 22
6. Input Mode........................................... 25
7. Cleaning and Troubleshooting.......... 26
7.1. Cleaning....................................... 26
7.2. Troubleshooting............................ 27
 7HFKQLFDO6SHFL¿FDWLRQV .................... 28
8.1. CDP4260-TL ................................ 28
8.2. CDP5560-TL ................................ 30
8.3. RS232 Command Table ............... 32
9. Other Information ............................... 35
Customer Support................................. 35
Limited Warranty .................................. 36
Mexico Limited Warranty ...................... 38
1. Unpacking and Installation...................1
1.1. Unpacking .......................................1
1.2. Package Contents...........................1
1.3. Installation Notes.............................1
1.4. Installing and Removing Table
Stands (optional).............................2
1.5. Installing and Removing OPS
module (CDP4260-TL/
CDP5560-TL series) (optional)........3
1.6. Mounting on a Wall..........................3
1.6.1. VESA Grid.............................4
2. Parts and Functions ..............................5
2.1. Control Panel ..................................5
2.2. Input/Output Terminals ....................6
2.3. Remote Control...............................7
2.3.1. General functions..................7
2.3.2. Inserting the batteries in
the remote control.................8
2.3.3. Handling the remote control..8
2.3.4. Operating range of the
remote control.......................8
3. Connecting External Equipment ..........9
3.1. Connecting External Equipment
(DVD/VCR/VCD) .............................9
3.1.1. Using COMPONENT video
input ......................................9
3.1.2. Using HDMI video input ........9
3.2. Connecting a PC.......................... 10
3.2.1. Using VGA input................. 10
3.2.2. Using DVI input.................. 10
3.2.3. Using HDMI input............... 10
3.3. Connecting Audio Equipment....... 11
3.3.1. Connecting external
speakers ............................ 11
3.3.2. Connecting an external
audio device....................... 11
3.4. Connecting Multiple Displays in
D'DLV\FKDLQ&RQ¿JXUDWLRQ ......... 12
3.4.1. Display control connection. 12
3.4.2. Digital video connection..... 12
3.4.3. Analog video connection.... 12

vii
Copyright Information
Copyright © ViewSonic Corporation, 2014. All rights reserved.
ViewSonic© and the three birds logo are registered trademarks of ViewSonic Corporation.
ENERGY STAR®is a registered trademark of the U.S. Environmental Protection Agency (EPA).
As an ENERGY STAR®partner, ViewSonic Corporation has determined that this product meetsthe
ENERGY STAR®guidelines for energy efficiency.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions
contained herein; nor for incidental or consequential damages resulting from furnishing this
material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right to
change product specifications without notice. Information in this document may change without
notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose
without prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it becomes
available, please register your product on the Internet at: www.viewsonic.com.
The ViewSonic®Wizard CD-ROM also provides an opportunity for you to print the registration form,
which you may mail or fax to ViewSonic.
For Your Records
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date:
CDP4260-TL/CDP5560-TL
ViewSonic LCD Monitor
VS15795/VS15796
CDP4260-TL/CDP5560-TL_UG_ENG Rev. 1A 04-22-14
Product disposal at end of product life
ViewSonic respects the environment and is committed to working and living green. Thank you for
being part of Smarter, Greener Computing.
Please visit ViewSonic website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

1
1. Unpacking and Installation
1.1. Unpacking
• This product is packed in a carton, together with the standard accessories.
• Any other optional accessories will be packed separately.
• Due to the size and weight of this display it is recommended for two people to move it.
• After opening the carton, ensure that the contents are complete and in good condition.
1.2. Package Contents
Please verify that you received the following items with your package content:
• LCD display
• CD ROM
• Remote control with AAA
batteries
• Quick Start Guide
• Power cord (1.8 m)
• VGA cable (1.8 m)
• RS232 cable (1.8 m)
• USB cable (Type B)
For EU For China
For North America For UK
*
**
*
Remote Control
and AAA Batteries
Video Signal Cable
(D-SUB to D-SUB Cable)
CD ROM
POWER
SMART VIDEO
SOURCE
PIP
INPUTON/OFF CHANGE
BRIGHTNESSCONTRAST
DISPLAY
AUTO
ADJUST
VOL UP
VOL DOWN
EXIT
MENU
SET
AUDIO
SOURCE
OPTION
Quick Start Guide
RS232 Cable
USB Cable
* The supplied power cord varies depending on destination.
NOTES:
• For all other regions, apply a power cord that conforms to the AC voltage of the power socket and has
been approved by and complies with the safety regulations of the particular country.
• You might like to save the package box and packing material for shipping the display.
1.3. Installation Notes
• Due to the high power consumption, always use the plug exclusively designed for this product. If an
extended line is required, please consult your service agent.
• 7KHSURGXFWVKRXOGEHLQVWDOOHGRQDÀDWVXUIDFHWRDYRLGWLSSLQJ7KHGLVWDQFHEHWZHHQWKHEDFNRI
the product and the wall should be maintained for proper ventilation. Avoid installing the product in the
kitchen, bathroom or any other places with high humidity so as not to shorten the service life of the
electronic components.
• The product can normally operate only under 3000m in altitude. In installations at altitudes above 3000m,
some abnormalities may be experienced.

2
1.4. Installing and Removing Table Stands (optional)
To install table stands:
1. Ensure your display is powered off.
2. 6SUHDGDSURWHFWLYHVKHHWRQDÀDWVXUIDFH
3. Grab the carrying handles and place the display face-down on the protective sheet.
4. After inserting the stand in the guide block, tighten the screws on both sides of the display.
NOTE: The longer side of the stand should face the front of the display.
Carrying handle
Thumbscrews
Longer portions face the front
Table stand
To remove table stands:
1. Power off the display.
2. 6SUHDGDSURWHFWLYHVKHHWRQDÀDWVXUIDFH
3. Grab the carrying handles and place the display face-down on the protective sheet.
4. Remove screws using a screwdriver and place them in a safe place for reuse.