Viking Professional & Designer 200 Series User manual

Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
[phone]
For product information,
call 1-888-VIKING1 (845-4641)
or visit the Viking Web site at
vikingrange.com
F20408F EN (111109J)
Professional & Designer 00/3 5/450 Series
Built-In Dishwashers
Viking Installation Guide

IMPORTANT–Please Read and Follow!
3
Site Preparation It is recommended that a thorough site inspection be
conducted PRIOR to unpacking and moving this appliance.
WARNING
Make sure that incoming voltage is the
same as unit rating. An electric rating
plate specifying voltage, hertz, and amps
is attached to the product. Wiring the
dishwasher with more voltage than it is
rated for may cause severe damage. To
reduce the risk of fire, electric shock, or
injury to persons, installation work and
electrical wiring must be done by ualified
technician in accordance with all
applicable codes and standards, including
fire-rated conditions.
WARNING
The dishwasher door may not stay open
by itself until the door panel is installed.
Be aware of this when fastening the
dishwasher to the cabinet.
WARNING
Plumbing connections must comply with
applicable sanitary, safety and plumbing
codes.
WARNING
Electrical power must be turned off at
circuit breaker or fuse box before making
electrical connections. Disconnect the
electrical power supply and place a tag at
the disconnect switch indicating that you
are working on the circuit.
• Before beginning–please read these
instructions completely and carefully.
• Do not remove permanently affixed labels,
warnings, or rating plates from the
dishwasher. This may void warranty or
create an unsafe product.
• Please observe all national and local
codes.
• Please ensure that this product is properly
grounded.
• The installer should leave these
instructions with the consumer who should
retain for local inspector’s use and for
future reference.
• The dishwasher has a factory installed
backflow preventer. Do not add an
additional check valve.
• Failure to provide a 20” above floor level
(50.8 cm) high loop may result in improper
operation of the dishwasher.
Table of Contents
Warnings & Important Information ______________________________________ 3
Dimensions & Cutout Dimensions ______________________________________ 6
Specifications ________________________________________________________ 7
Custom Door Panel Specifications ______________________________________ 8
Custom Door Panel Installation Option _________________________________ 9
General Information _________________________________________________ 10
Site Preparation __________________________________________________ 10
Water Supply ____________________________________________________ 10
Drain____________________________________________________________ 10
Electrical Connections ____________________________________________ 11
Hardwire Conduit Option _____________________________________________ 12
Trim Installation Options _____________________________________________ 13
Counter Balance Spring Adjustment ___________________________________ 16
Installation Procedure_________________________________________________ 17
Performance Checklist _______________________________________________ 21
Testing for Leaks _________________________________________________ 21
Final Preparation _________________________________________________ 21
Service & Registration ________________________________________________ 22
2

54
IMPORTANT–Please Read and Follow!
IMPORTANT–Please Read and Follow!
A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local
la s, or local ordinances.
• The required use of a GFI is normally related to the location of a receptacle with respect to
any significant sources of water or moisture.
• Viking Range Corporation will NOT warranty any problems resulting from GFI outlets which
are not installed properly or do not meet the requirements below.
If the use of a GFI is required, it should be:
• Of the receptacle type (breaker type or portable type NOT recommended)
• Used with permanent wiring only (temporary or portable wiring NOT recommended)
• On a dedicated circuit (no other receptacles, switches or loads in the circuit)
• Connected to a standard breaker of appropriate size (GFI breaker of the same size NOT
recommended)
• Rated for Class A (5 mA +/- 1 mA trip current) as per UL 943 standard
• In good condition and free from any loose-fitting gaskets (if applicable in outdoor situations)
• Protected from moisture (water, steam, high humidity) as much as reasonably possible
WARNING
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
WARNING
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector
in terminal box.
Do not use an extension cord.
Failure to follow these instructions, can result in
death, fire or electrical shock.
WARNING
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.

Dimensions & Cutout Dimensions
6 7
23
-
7/8”
(60.6 cm
)
20
-
1/4”
(51.4 cm)
33
-
7/8”
(86.0 cm)
49”
(124.5 cm)
26-3/8”
23-3/4”
2-5/8”
26-3/8”
23-1/8”
3-3/16”
Cabinet Flush Panel Flush
26-3/8”
23-1/8”
2-7/8”
26-3/8”
23-3/4”
2-1/4”
Panel FlushCabinet Flush
23-1/8”
23-3/4”
Panel FlushCabinet Flush
Designer Series
Professional Series
Custom Panel (200/450 Models)
24”
(61.0 cm)
24”
(61.0 cm)
34” min.
(86.4 cm
)
35” max.
(89.0 cm
)
Note: A 2”
(5.1 cm) cut-out is
required for
water supply and
discharge lines.
(59.0 cm)
(60.3 cm)
(6.7 cm) (8.1 cm)
(67.0 cm) (67.0 cm)
(67.0 cm)
(60.3 cm)
(60.3 cm)
(67.0 cm)
(59.0 cm)
(7.3 cm)
(5.7 cm)
(59.0 cm)
Specifications
Built-In Dishwasher
Description 200/325/450 Models
Overall width 23-7/8” (60.6 cm)
Overall height from floor 33-7/8” (86.0 cm) min.
35” (89.0 cm) max.
Overall depth from rear–Professional To edge of side - 24” (61.0 cm) - includes door panel
With door open - 49” (124.5 cm)
Overall depth from rear–Designer To edge of side - 24” (61.0 cm) - includes door panel
With door open - 49” (124.5 cm)
Cutout width 24” (61.0 cm)
Cutout height 34” (86.4 cm) min.
35” (89.0 cm) max.
Cutout depth 24” (61.0 cm)
Electrical requirements 15.0 amps, 120VAC/60 Hz;
5’ (1.8 m) electrical cord 3 prong plug supplied with unit
Water-heating element rating 200 model - 1200 watts 325/450 models - 1400 watts
Inlet water temperature 120 F (49 C) recommended;
Dishwasher will perform properly with cold water
Note: Cycle times will vary
Inlet water pressure operating range 10 to 125 psi (.69 to 8.62 bar)
Inlet water hose 5’ (1.5 m) braided stainless steel water line with 3/8” (0.95 cm) compression
fitting connected to dishwasher
Drain hose 7’ (2.13 m) 1/2” (1.3 cm) ID “crimp-proof” flexible drain hose
attached to dishwasher, connections provided for 5/8” (1.6 cm),
3/4” (1.9 cm) or 1” (2.5 cm), cut as required
Drain hose high loop required Height from floor - 20” (51.0 cm) min.
Approximate shipping weight 200 model -147 lbs. (66.7 kg) 325 model -152 lbs. (68.9 kg) 450 model -157 lbs. (71.2 kg)

11-17/32"
(29.3 cm)
29-3/4"
(75.6 cm)
to
31-1/4”
(79.4 cm)
22-21/32"
(57.5 cm)
23-9/32"
(59.1 cm)
10"
(25.4 cm)
10-5/8"
(27.0 cm)
5-7/8"
(14.9 cm)
5/8"
(1.6 cm)
5/8"
(1.6 cm)
5/8"
(1.6 cm)
ø1/8" 4 places
(.3 cm)
Use 1/4"
router bit
29"
(73.7 cm)
8
Custom Door Panel
(Specifications for DFB Models - 200/450 Models)
9
a
To remove face panel of dishwasher remove only the
4 Phillips screws - do not remove any other fasteners.
b
Position custom face panel on front of dishwasher.
Use non-marring clamps to hold custom panel in place.
Secure with #8 1-3/4”(4.5 cm) long, stainless steel flat
head screws.
c
(Installation Option)
Have the overlay panel constructed per
dimensions. The panel thickness MAY NOT
exceed 5/8” (1.6 cm) for flush installation in most
cabinets. Ensure that the design, construction,
and installation of the panel overlay and its
handle mounting is sufficient to reliably operate
in this application with a maximum panel weight
of 18 lbs. (8.2 kg.) Custom panels should not
exceed 18 lbs. (8.2 kg.)
Obtain four screws with the proper thread type
for the overlay material chosen. The screws
MUST BE #8 flat head, 1-3/4” long and MUST
BE stainless steel to avoid corrosion.
If dishwasher has a metal door skin installed,
remove the four screws. DO NOT remove any
other fasteners and ensure that only the proper
screws are removed.
Carefully tighten each screw to secure the
overlay and check to ensure that the overlay is
square with the dishwasher door and cabinet
opening and that the panel doesn’t interfere
with the operation of the dishwasher.
Verify operation of the door counter balance
springs after installation of the overlay panel.
The additional weight of the overlay panel might
require an adjustment to the preload of the
counterbalance springs. If adjustment of the
springs is required, please refer to the “Counter
Balance Spring” section.
NOTE: Back side of pa el show . Use cautio ot to drill through fro t of pa el.

Electrical Connections
Grounding Instructions
This appliance must be grounded. In the
event of a malfunction or breakdown,
grounding will reduce the risk of electric
shock by providing a path of least resistance
for electric current. This appliance is
equipped with a cord having an equipment-
grounding conductor and a grounding plug.
The plug must be plugged into an
appropriate outlet that is installed and
grounded in accordance with all local codes
and ordinances.
Grounding Instructions if Hardwired:
This appliance must be connected to a
grounded metal, permanent wiring system; or
an equipment grounding conductor must be
run with the circuit conductors and connected
to the equipment – grounding terminal or
lead on the appliance.
• For a cord connected undercounter
dishwasher:
1. The power supply receptacle for the
appliance should be installed in a
cabinet or on a wall adjacent to the
under counter space in which the
appliance is to be installed;
2. There should be an opening through the
partition between the compartments
mentioned in Item (1), that is large
enough for the attachment plug to pass
through. The longest dimension of the
opening shall not be more than 1-1/2”
(38 mm).
11
General Information
3. The edges of the opening mentioned in
Item (2) should, if the partition is wood,
be smooth and rounded or, if the
partition is metal, be covered with the
grommet provided for this purpose by
the manufacturer; and
4. Care should be exercised, when the
appliance is installed or removed to
reduce the likelihood of damage to the
power supply cord.
• The dishwasher comes with a 5’ (1.8 m)
electrical cord for 110-120 volts, 15/20 amp
supply. This cord should be plugged into
the 110-120 volt outlet located under the
sink.
• If the cord is not long enough or if a hard
wire installation is needed, follow the
instructions on page 10.
NOTE: Access holes should be 2” square (5.1
cm) with o sharp edges.
• In a hardwire installation, use only copper
supply conductors. The conductors should
have a minimum temperature rating of
194 F (90 C).
WARNING
Disconnect the electrical power supply and
place a tag at the disconnect switch
indicating that you are working on the
circuit.
WARNING
Be sure electrical power is turned off at
circuit breaker or fuse box before servicing
or installing unit. Do not use an extension
cord for this appliance.
WARNING
Improper connection of the e uipment –
grounding conductor can result in a risk of
electric shock. Check with a ualified
electrician or serviceman if you are in
doubt as to whether the appliance is
properly grounded. Do not modify the plug
provided with the appliance; if it will not fit
the outlet, have a proper outlet installed by
a ualified electrician.
General Information
• Read these instructions carefully and
completely before installing the dishwasher.
The installation should be carried out by a
qualified installer, who is familiar with all
local codes and ordinances for electrical
and plumbing connections. If the
dishwasher is being installed for the first
time, most of the work has to be done
before you move it into place. If you are
replacing an old dishwasher, you must
check the old connections.
• Electrical requirements are listed in the
“Specifications” section (page 5).
Site Preparation
NOTE: It is recomme ded that a thorough
site i spectio be co ducted PRIOR to
u packi g a d movi g this applia ce.
•After determining where the water
supply line will connect to the
dishwasher, provide a 2” (5.1 cm) access
hole and run the line to the approximate
fill valve location. Sealing access area
once lines are in place is recommended.
• Confirm available access to adequate power.
Water Supply
• Water pressure for the water supply should
be a minimum of 10 to 125 psi. The
dishwasher is supplied with a 5’ (1.5 m)
braided stainless steel water line with 3/8”
(0.95 cm) compression fitting connected to
dishwasher.
• After determining where the water supply
line will connect to the dishwasher, provide
a 2” (5.1 cm) access hole and run the water
supply line to the approximate fill valve
location.
• For service convenience, a shut-off valve
(not supplied) should be installed in the
supply line in a readily accessible location
(such as beneath the sink).
•It is recommended that the dishwasher
be connected to a hot water supply. If a
cold water supply is used, cycle times will
vary.
• It is important that the water supply line and
the shut-off valve have a sufficient flow
volume. Flush the supply line prior to
connecting it to the intake line of the
dishwasher.
• Make sure the connection is sealed and not
leaking before completing the installation.
Drain
• The access hole for the drain line should be
2” square (5.1 cm). Locate as low and as
near to the back wall as possible.
• Do not use any fittings anywhere in the drain
line that are less than 1/2” (1.3 cm) ID.
• If the drain line is going to be connected to
a food waste disposer, be sure to remove
the knockout or plug from the fitting before
connecting drain line.
• Drain connection should be a minimum of 9”
(22.9cm) from the floor. If connection is
lower, siphoning during cycle can occur.
NOTE: The e d of the drai hose is
1” (2.5 cm), but is adjustable to 3/4” (1.9 cm) or
5/8” (1.6 cm). If the drai co ectio is smaller
tha 1” (2.5 cm), the hose ca be cut to fit the
co ectio .
NOTE: Be sure to ru the drai li e through
the hole to the si k compartme t before
movi g the dishwasher i to place.
10
WARNING
Plumbing connections must comply with
applicable sanitary, safety, and plumbing
codes.
CAUTION
The dishwasher has a factory installed
backflow preventer. Do Not add an additional
check valve.

UL approved
strain relief
d
Common
Green
Ground
White
Black
Run wires through bottom pan. Using a UL approved
strain relief, connect wires to terminal block.
e
Green
Ground
Connect ground wire.
NOTE: Rei stall fro t plate a d bottom pa .
12 13
Hardwire Conduit Option
a
1
b
Remove any loose items in the dishwasher and carefully lay
the dishwasher on its back. NOTE: Be careful ot to pi ch
hoses or power cord be eath dishwasher.
Remove bottom pan and front plate.
c
Loosen ground wire and wires on terminal block.
Loosen strain relief and remove cord.
NOTE: Other items are grou ded i this locatio –these
items must remai grou ded.
Trim Installation Options (not available on all units)
1a
To install dishwasher without trim, remove the 6 screws and washers (3 per
side) and remove trim. To attach wiper gasket to dishwasher, pull protective
film off adhesive back on wiper gaskets and apply to leading edge of
dishwasher frame. Trim gasket to fit.
1b

14 15
Trim Installation Options (cont’d.) (not available on all units)
Trim Installation Options (cont’d.) (not available on all units)
2a
Dishwasher will ship with trim installed for panel flush install. If needed,
attach wiper gasket by pulling protective film off adhesive back on wiper
gasket and apply behind hemmed edge of side trim.
2b
3a
To install dishwasher cabinet flush with trim, remove the 6 screws and washers (3
per side) holding side trim on. Shift the side trim forward. Use rear hole on side
trim and the same hole on dishwasher to reattach trim. If needed, attach wiper
gasket by pulling protective film off adhesive back on wiper gasket and apply
behind hemmed edge of side trim.
3b

Disconnect cable from hook.
a
Set counter balance spring connector in appropriate
location.
2
1
b
Increase
tension
Decrease
tension
Reconnect cable to hook.
c
Counter Balance Spring Adjustment - If Necessary
NOTE: For custom pa el
i stallatio , the door may
require adjustme t to the
preload of the cou terbala ce
spri gs. Follow these steps to
adjust the te sio .
16 17
Using tie strap attached to dishwasher, band water line,
drain line, and power cord together.
Position unit in front of cutout.
2
3
Installation Procedure
4
Carefully lay dishwasher on its back and attach the kick
plate brackets. Screws for the brackets will already be
in the base. NOTE: Be careful ot to pi ch hoses or
power cord be eath dishwasher.
1
1
Slide unit into opening; be sure to feed water, electrical
and discharge lines into adjacent cabinet.
Using a level, adjust to appropriate height. Left and right
adjust side to side and center adjusts front to back.
(Select models only)
Equal distance
5a
DownUp
To check level, front to back, pull the top rack half-way
out of unit. The rack should remain stationary and not
move in or out.
5b

Remove front panel to access the front leveling legs.
6a
Front Panel Removed
Front Panel Attached
6a
Front Panel Removed
Front Panel Attached
Installation Procedure (cont’d.)
18 19
Leveling legs will be raised during shipping. Adjust
front leveling legs down by using a 1/4 drive ratchet.
When the adjustment nut is visible, complete the
lowering of the legs from the top. When the legs are
down, tighten the locking nut on the top of the leg.
To level the dishwasher, take a level and use Step 6b to
adjust front legs to appropriate height. Use Step 5a to
adjust back leg to appropriate height. See Step 5b to
insure levelness from front to back. Adjust legs until the
rack is stationary. After unit is level, replace front panel
and insure that overflow channel is in place.
6b
(Standard discharge)
10B
Attach screws through trim pieces
into cabinets.
7
1.0”
(2.5 cm)
Cut here for 3/4”
(1.9 cm)
Cut here for 5/8”
(1.6 cm)
9
10A
(Discharge with food waste disposer)
Identify discharge connection size; cut line to correct size
and connect. Clamp if necessary.
Minimum
20”
(50.8 cm)
from floor
8
Install High Loop Clip, which is provided, a minimum of
20” (50.8 cm) from the floor.
Installation Procedure (cont’d.)

20 21
Installation Procedure (cont’d.)
11A
Air Gap
(Discharge with food waste disposer and air gap)
11B
Air Gap
(Discharge with air gap)
Connect water line.
12
13
Plug LED light into dishwasher (select
models only) and install kick plate.
Performance Checklist
Testing for Leaks
A qualified installer should carry out the
following checks:
hRemove packaging and parts.
hTurn on the water supply and check for
leaks.
hTurn the power on at breaker/fuse box
and test the dishwasher operation by
running a rinse and hold cycle. (This
should take about 12 minutes.)
hTurn off the electrical power and check
for leaks under the dishwasher.
hMake sure that no kinks have developed
in the drain lines.
Final Preparation
• Some stainless steel parts may have a
plastic protective wrap which must be
peeled off.
Cycles Options
Unit Reset
• If the unit should need to be reset for any
reason, push and hold the “START” button
for 4 seconds.

2322
Only authorized replacement parts may be used in performing service on the appliance. Do not
repair or replace any part of the appliance unless specifically recommended in the manual. All
servicing should be referred to a qualified technician.
Contact Viking Range Corporation, 1-888-VIKING1 (845-4641), for the nearest service parts
distributor in your area or write to:
VIKING RANGE CORPORATION
PREFERRED SERVICE
1803 Hwy 82W
Greenwood, Mississippi 38930 USA
The serial number and model number for your dishwasher are located on the identification plate
mounted on the bottom left side of the dishwasher door opening.
Record the following information indicated below. You will need it if service is ever required.
Model number ____________________________________________________________________________________
Serial number _____________________________________________________________________________________
Date of purchase __________________________________________________________________________________
Date installed ______________________________________________________________________________________
Dealer's name _____________________________________________________________________________________
Address ___________________________________________________________________________________________
These installation instructions should remain with the unit
for future reference.
Service & Registration