Vintage Keeper CURVED CORNER F04 A User manual

CALIFORNIA REDWOOD WINERACK
CURVED CORNER MODULES
ASSEMBLY &INSTALLATION GUIDE
CURVED CORNER F04 (B)
CURVED CORNER F04 (A)
Rosehill Wine Cellars | Toll Free: 1-888-253-6807
www.rosehillwinecellars.com

TOOLS
COMPONENTS
Vertical Column Horizontal Bar
HARDWARE
Nails x 96Bracket x 6 7/8” Screw x 8
Philips Screwdriver Hammer Level Drill
8”
1”-1 1/8” Finishing Nailer
Highly recommended to prevent splitting of wood. This tool is also
handy for projects around the home.

SORTING AND SETTING UP BARS :
Redwood has a variety of natural colours, ranging from red to white.
If consistent colour is important to you, sort the bars before assembly.
Make sure all column TOPS are oriented in the same direction.
For identifying the TOP ends refer to illustrated zoom view.
Hold bars rmly in place one at a time and nail through column into bar
ends ( gure A ).
IMPORTANT NOTE :
The Curved Corner 4, type B (F04B) is illustrated in the following
instructions. Curved corner modules consist of four separate column
sections which are bracketed together to form a quarter-circle.
GETTING STARTED
STEP 1
A
TOP

STEP 2
NAIL COLUMN TO BARS :
Flip column, make sure the column TOPS are orientated in the same
direction. Bring the two columns together with bar ends interlocked to
top column. Nail two nails at each corner ( gure A ).
A
TOP

STEP 3
NAIL COLUMN TO ASSEMBLY :
Interlock the remaining bars to the vertical column. Nail through column
into bar ends ( gure A ). :
A

STEP 4
JOIN SECTIONS TOGETHER WITH BRACKET :
Use Curved Corner brackets to join individual column sections together.
Stand column sections end to end, with TOP column ends facing up.
Insert brackets between sections, as shown, then push down over the
horizontal bottle rests.

STEP 5
SCREW ALLADJOINING WINERACKS TOGETHER :
BEFORE ATTACHING TO WALL : For a professional look, install a Base
Trim Kit* (shown on the last page) before mounting rack to wall.
To avoid cracking of wood, pre-drill 1/16” holes for screws ( gure A ).
Curved corner modules MUST be securely fastened to adjacent racks.
Fasten through adjoining vertical bars with 7/8” screws. Also fasten
through rear bars of adjoining column sections as well as the front
( gure B ).
When stacking units on top of one
another, fasten adjoining horizontal
bars with 7/8” screws at two places
per module. Also fasten through
rear bars of adjoining column sec-
tions as well as the front (gure B).
For additional strength and stability,
we strongly recommend you fasten
through bottom horizontal bars into
the oor or base with 7/8” screws
or nails.
A
B
A
B

LIMITED WARRANTY
Drobot Inc warrants this product to be free from defects due to workmanship or
material, under normal use and service, for a period of one (1) year after the date of
purchase. Please call our customer service department at 1-888-274-8813 or e-mail
us at [e-mail]
This warranty does not cover normal cosmetic wear, cosmetic defects, damage
resulting from improper assembly or maintenance, shipping damage, accident, or any
misuse, abuse or use contrary to the written instructions. This product is not war-
ranted for commercial use.
The warranties expressed above constitute the entire warranty of Drobot Inc with
regard to its products and are in lieu of and exclusive of all other warranties, express
or implied, including any of merchantability or tness for a particular purpose. In no
event shall Drobot Inc be liable or responsible for incidental or consequential damages,
including spoilage or breakage of wine. It is your own responsibility to insure your wine,
and to take all reasonable and necessary precautions to safeguard its condition.
© Drobot Inc, 2007
Use of WINERACK is strictly at your own risk. Drobot Inc. will not accept
any responsibility or liability for damages resulting from units not assem-
bled precisely as directed, or not securely fastened to a wall or support
with suitable fasteners.
Before placing any bottles in your WINERACK, test it thoroughly to make
sure all fasteners are secure.
* BASE AND TRIM KIT
Provides a solid base and professional nish for your WineRack project;
The bases come in 3 different lengths 16”,32”,48” and two corner ver-
sions (convex and concave). You can order one directly from Vintage
Keeper or from your dealer.
With base section in place, check for level and adjust with shims as
required. When racks are in place, fasten the lower horizontal bars
directly to Base with screws or nails. Nail moldings to face of base and
racks.
TEST BEFORE USE
RACK
WALL 1/2”
1/2”
1 3/16”
6 1/8”
9”
TRIM
MELAMINE
BASE