Vintage view W Series User manual

W Series Wine Rack Frame 10
Installation guide for the standard W Series Frame 10 (FCF-HD)
Included:
• (2) 60” Frame Sections
• (2) Frame Couplers
• (36) Self-drilling screws
Important Note:
These installation instructions will assist you with installing the VintageView Vino Series Post System in standard
oor-to-ceiling applications. If using upgraded mounting plates, refer to individual product install guides. The Post
System is designed for ceiling heights of up to 10’ (3,048mm).
Fasteners:
Fasteners for securing Mounting Plates to the Vino Series Posts are provided (self-drilling screws). Each mounting
Plate is pre-drilled for installing Post. When installing nished Vino Series Post to the oor or ceiling, please use
the following recommendations for fasteners:
Additional Components:
(sold separately)
• W Series Wine Racks
• W Series Rack Couplers
• W Series Frame Backer Bar
(single-sided displays)
• Mounting Hole Covers
Required Tools:
• Drill
• Phillips head drill bit
• Phillips head screwdriver
• Level
• Pencil or Marker
• Tape measure
• Metal cutting saw
• Metal le

Instructions: W Series Wine Rack Frame 10’
Figure A
Figure B
1. IDENTIFY PROPER HARDWARE
Using the chart on the previous page, identify the proper
oor/ceiling hardware (not included) that will be needed
for your specic project. For drywall surfaces, Vinta-
geView recommends installing to joists or wood backing
when available.
2. MEASURE CEILING HEIGHT
Measure the desired location’s ceiling height.
3. INSERT FRAME COUPLERS
Insert two (2) Frame Couplers to the section of the Frame
that will be used for the Bottom (Figure A).
4. MARK CUT LINES
Lay each section, interlaced, as shown above (Figure B).
Position the Frame so that the measurement from top to
bottom of the base plates equals your ceiling height.
Use a pencil or marker to mark any overlap on the bot-
tom of the Post Top, which is the side that features a hol-
lowed out opening. Ensure that the mark is at the widest
part of the Coupler (Figure C).
If the cut mark aligns with a cross member, measure and
cut 2in (51mm) off the bottom Section using a Metal Cut-
ting Saw and start the step over (Figure D).
5. CUT THE FRAME
Using a Metal Cutting Saw, squarely cut the Frame Top at
the mark. Smooth the end of the Frame with a Metal File.
Do not use abrasive saws as they may damage the
finish.
6. CONNECT THE FRAME
Connect the top Section to the Bottom, ensuring the
Couplers are rmly lodged into both ends of the
Frame (Figure E).
Figure C
Figure D
Figure E

Instructions: W Series Wine Rack Frame 10’
7. MARK CEILING/
FLOOR MOUNTING HOLES
Place the Frame in desired location. Ensure it is plumb
with a level and mark the mounting holes on both the
ceiling and the oor. Set the Frame aside and pre-drill
any required pilot holes based on hardware selection.
8. BUILD THE RACKS
It is common to use one (1), two (2), or (3) W Series
Wine Racks on one or both sides of a W Series Frame. If
using more than one, connect the W Series Wine Rack-
ing by removing the two (2) Endcaps from the end of
each Wine Rack where they will connect.
Connect the Neck Strips (smaller bottle impressions) to-
gether with the supplied Wine Rack Couplers (Figure F).
Repeat with the Base Strips (larger bottle impressions).
VintageView recommends leaving a minimum of 6in
(153mm) above and below the W Series Racks when
assembled to Frame.
9. PLACE THE RACKS
Lay the connected Strips in the desired location on the
Frame, ensuring the Neck Strips are facing in preferred
direction. IMPORTANT: One single Wine Rack Strip must
extend 12in (305mm) above or below all connection
points of the Frame (Figure G).
10. SECURE THE RACKS
Attach the Racking Assembly to the Frame using two (2)
or three (3) Self Drilling Screws per Strip (quantity will
vary based on individual height of racking).
Then press two (2) or three (3) Mounting Hole Covers
into each Strip section (quantity will vary based on indi-
vidual height of racking).
11. SECURE THE BACK
All connection points on the backside of the Frame
must be supported by either Wine Racking or a W
Series Frame Backer Bar.
For Single Sided Displays
Use eight (8) Self-Drilling Screws to attach two (2)
W Series Frame Backer Bars (FCF-BACK) to the back
side of the Frame, centered over the two connection
points. Then press eight (8) Mounting Hole Covers
over the Screws.
Figure F Figure G
Figure H
Figure I

Instructions: W Series Wine Rack Frame 10’
For Double-Sided Displays
Repeat Steps 8-10 to install Wine Racks to the back side
of the Frame (Figure J).
IMPORTANT: The Backer Bar or Wine Racking must ex-
tend 12in (305mm) above or below all connection points
of the Frame.
12. INSTALL THE SYSTEM
Stand the Frame Assembly in the desired location and
ensure it is plumb both front and back and side-to-side
with a level (Figure K).
Secure the Frame to the ceiling (Figure L) using two (2) of
the appropriate fasteners (not provided). Double check
the Frame is plumb and secure the Frame to the oor
using two (2) of the appropriate fasteners (not provided).
13. ADD WINE
Only the good stuff.
Problems?
Try BILT 3D intelligent instructions, visit
www.vintageview.com, or call 303-504-9463.
Maintenance and Care:
The W Series Frame should be regularly checked for
tightness. Should any rack be found to be loose, tighten
by hand until secure. All components of the W Series
Frame System may be cleaned with a damp cloth and
mild dish soap - abrasive pads or steel wool should NOT
be used as they will damage the nished surfaces of the
parts.
Figure J Figure K
Figure L