Vip2 VK2 -600PTZ User manual

VK2 -600PTZ
Configuration and User manual

II
VK2-600PTZ User manual
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE
VENTILATION GRILLS OR OTHER OPENINGS ON THE EQUIPMEMT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral is intended to alert the user
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.

III
VK2-600PTZ User manual
CE COMPLIANCE STATEMENT
WARNING
THIS IS A CLASS A PRODUCT. IN A DOMESTIC ENVIRONMENT THIS
PRODUCT MAY CAUSE RADIO INTERFERENCE IN WHICH CASE THE USER
MAY BE REQUIRED TO TAKE ADEQUATE MEASURES.

IV
VK2-600PTZ User manual
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been moisture, does not operate normally, or has been
dropped.
15. CAUTION –THESE SERVICING INSTRUCTIONS ARE FOR USE BY
QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF
ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT
CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU QRE
QUALIFIED TO DO SO.
16. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2
power source only.

V
VK2-600PTZ User manual
Table of Contents
Chapter 1 —Introduction...........................................................................................................1
1.1 Features.............................................................................................................................................1
Chapter 2 —Installation and Configuration.........................................................................2
2.1 Package Contents............................................................................................................................2
2.2 Installation.........................................................................................................................................3
2.3 Basic Configuration of Dome Camera System........................................................................4
2.4 Setting Dome Camera Address (ID)............................................................................................5
2.5 Connections......................................................................................................................................5
2.6 IP Assignment..................................................................................................................................6
2.7 Getting Started.................................................................................................................................7
Chapter 3 —Operation by Web Browser ..............................................................................8
3.1 Access from a browser..................................................................................................................8
3.2 Access from the internet...............................................................................................................9
3.3 Setting the admin password over a secure connection........................................................9
3.4 Live View Page.................................................................................................................................9
3.5 Network Camera Setup ................................................................................................................11
3.5.1 Basic Configuration...............................................................................................................12
1) Users..........................................................................................................................12
2) Network......................................................................................................................13
3) Video & Image ........................................................................................................... 14
4) Audio..........................................................................................................................16
5) Date & Time ............................................................................................................... 17
3.5.2 Video & Image.........................................................................................................................18
3.5.3 Audio .........................................................................................................................................19
3.5.4 Event..........................................................................................................................................19
1) Event-In......................................................................................................................19
2) Event-Out...................................................................................................................23
3) Event Map.................................................................................................................. 29
3.5.5 System ......................................................................................................................................31
1) Information ................................................................................................................31
2) Security......................................................................................................................31
3) Date & Time ............................................................................................................... 34
4) Network......................................................................................................................35
5) Language...................................................................................................................42
6) Maintenance ..............................................................................................................42
7) Support......................................................................................................................43

VI
VK2-600PTZ User manual
3.6 PTZ Control.....................................................................................................................................44
3.7 Help...................................................................................................................................................45
3.8 Resetting to the factory default settings.................................................................................46
3.9 System Requirement for Web Browser ...................................................................................46
Chapter 4 —Program and Operation (RS485 telemetry)................................................47
4.1 How to control the On-Screen Menu........................................................................................47
4.2 Accessing the On-Screen Menu................................................................................................47
4.3 Auto Scan ........................................................................................................................................48
4.4 Preset................................................................................................................................................50
4.5 Quick setting a Preset..................................................................................................................52
4.6 Tour ...................................................................................................................................................52
4.7 Pattern (Learn Tour)......................................................................................................................53
4.8 Area Title..........................................................................................................................................54
4.9 Privacy Zone...................................................................................................................................55
4.10 Camera Menu................................................................................................................................56
• FOCUS CONTROL.......................................................................................................56
• WB (White Balance) CONTROL..................................................................................57
• AE CONTROL ..............................................................................................................57
• DNR CONTROL............................................................................................................ 58
4.11 Dome Setup...................................................................................................................................59
• LANGUAGE SETUP.....................................................................................................59
• HOME FUNCTION SETUP ........................................................................................... 59
• OSD DISPLAY.............................................................................................................. 60
• VIEW ANGLE SETUP...................................................................................................61
• INITIALIZE DATA .........................................................................................................62
• ORIGIN OFFSET ..........................................................................................................63
• DOME RESET .............................................................................................................. 64
• SYSTEM MENU............................................................................................................64
• SYSTEM INFORMATION ............................................................................................. 66
4.12 Factory Setup...............................................................................................................................66
5 - Dome Communication (RS485 Addressing etc)..........................................................67
Appendix A —Specifications.................................................................................................68
Appendix B —Troubleshooting.............................................................................................71
Appendix C —Glossary...........................................................................................................71

1
VK2-600PTZ User manual
Chapter 1 —Introduction
1.1 Features
Dual video streams simultaneously at full frame rate in all resolutions up to D1 (720X480 in
NTSC, 720X576 in PAL) using Motion JPEG and H.264 (or MPEG-4).
Built-in 22:1 optical zoom with True Day/Night operation
Intelligent capabilities such as enhanced video motion detection
The encoder’s external inputs and outputs can be connected to devices such as sensors and
relays, enabling the system to react to alarms and activate lights or open/close doors.
Supports two-way audio
Logs all user access, and lists currently connected users. Also, full frame rate video can be
provided over HTTPS.
Interface Protocol: TCP/IP, UDP, IPv4/v6, HTTP, HTTPS, QoS, FTP, SNMP, uPnP, RTP,
RTSP, RTCP, DHCP, ARP.
120 Preset positions with the individual Camera AE setup
4 Tours consist of Presets, Patterns, Auto Scan and other Tours can be programmed with over
150 functions and Preset locations. While moving, each Preset scan can be watched in smooth
Vector Scan mode.
1 Auto Scan with the normal, the vector, and the random mode with 13 speed steps
4 Patterns (up to 200 second) and 4 Privacy Zones
8 Area Titles
1 Alarm input / 1 Alarm output
Variable speed from 0.1/sec to 380/sec
Three Variable speed (SLOW, NORMAL, TURBO)
Pan / Tilt speed is inversely proportional to the zoom ratio with the option.
Maximum speed is 380/sec when Preset command.
Auto Calibration from 0.1to 6(Tilt range is 0to 180).
Programmable user preferences (alarm, preset, title, etc.).
180Digital Flip
Up to 255 selectable camera addresses.
Multi-language Menu Display, Password Confirmation
Built-in RS-485 receiver driver
12VDC operation
Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

2
VK2-600PTZ User manual
Chapter 2 —Installation and Configuration
2.1 Package Contents
VK2-600PTZ is design to be a compact, vandal resistant dome camera.
The housing is constructed of aluminum, steel and plastic. The housing is designed to be
mounted both wall and ceiling type.
The housing meets the Protection Classification IP66 standards for dust and moisture resistance.
* Dome Camera ................................................................1
* Installation Guide/CD ....................................................1
* Template Sheet ..............................................................1
* Mounting Bracket ..........................................................1
* Safety Lanyard ..............................................................1
* Accessory Kit .................................................................1
1) Mounting screws (PH6 x 35.0) ..........(4)
2) Plastic anchors ..................................(4)
3) O-Rings ..............................................(4)
4) Torx wrench .......................................(1)
* Accessory Connector ....................................................1
1) 2Pin Terminal Block ...........................(1)
2) 3Pin Terminal Block ...........................(1)
3) 6Pin Terminal Block ...........................(1)

3
VK2-600PTZ User manual
2.2 Installation
VK2-600PTZ is for use in surface or pendent mounting applications and the mounting member
must be capable of supporting loads of up to 1.6kg. (Pendent mounting must use pendent mount
accessory.)
VK2-600PTZ’s mounting bracket should be attached to a structural object, such as hard wood,
wall stud or ceiling rafter that supports the weight of VK2-600PTZ.
CAUTION: Before installing the bracket to surface, adjust the four mounting screws "A"
on the base of the dome camera to best match the mounting bracket locked
position. Unscrew the locking screw on the side of the dome's base and fit the
tab of the mounting bracket into the locking slot. Screws "A" should not be too
tight or too loose when the dome is in the locked position. After setting the
proper positions of screws "A" remove the mounting bracket and install the
bracket onto the required surface. If it is difficult to lock the dome in position
after the mounting bracket has been installed, readjust the screws "A" by
unscrewing them a small amount and try to install dome camera again.

4
VK2-600PTZ User manual
2.3 Basic Configuration of Dome Camera System
No.
Wire Color
Description
1
Red: 12V DC+
White: 12V DC-
Main Power: 2pin terminal
2
Pink, Brown
Heater Power(Option): 3pin terminal
3
Black: GND
Gray: Alarm Input
Yellow: GND
Black&White: Alarm Output
Green: RS485+
Blue: RS485-
Alarm Input/Output, RS485: 6pin terminal
4
Black
Ethernet: RJ45 Modular Jack
5
Yellow
Video Composite Output: BNC Jack
6
Red
Audio line output: RCA Jack
7
White
Audio line input: RCA Jack
VK2-600PTZ must be installed by qualified service personnel in accordance with all local
electrical and building codes.
AC+ AC- AC+ AC- FGND (Rx+) (Rx-) Rx(Tx)+ Rx(Tx)- GND

5
VK2-600PTZ User manual
2.4 Setting Dome Camera Address (ID)
To prevent damage, each dome camera must have a unique address (ID).
When installing multiple dome cameras using a multiplexer, it is suggested that the dome camera
address match the multiplexer port number.
The factory default setting is 1.
Refer to ‘4.13 Dome Communication’section for detailed information.
2.5 Connections
• Connecting to the RJ-45
Connect a standard RJ-45 cable to the network port of VK2-600PTZ. Generally a cross-over
cable is used for directly connection to PC, while a direct cable is used for connection to a hub.
• Connecting Alarms
AI (Alarm In)
You can use external devices to signal VK2-600PTZ to react on events. Mechanical or electrical
switches can be wired to the AI (Alarm In) and G (Ground) connectors.
Please see “3.5.4 Event > 1) Event-In > ②Alarm In” for configuring alarm input.
G (Ground)
NOTE: All the connectors marked G or GND are common.
Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.
AO (Alarm Output)
VK2-600PTZ can activate external devices such as buzzers or lights. Connect the device to the
AO (Alarm Out) and G (Ground) connectors.
Please see “3.5.4 Event > 2) Event-Out > ④Alarm Out” for configuring alarm output.
• Connecting to the RS485
VK2-600PTZ can be controlled remotely by an external device or control system, such as a
control keyboard, using RS485 half-duplex serial communications signals.
• Connecting Video out connector
Connect the video out (BNC) connector to the monitor or video input.
• Connecting the Power
Connect the power of 12VDC 1.5A for VK2-600PTZ.
When using a 12VDC adapter, connector the positive(+) pole to the ‘+’ position and the
negative(-) pole to the ‘-‘ position.
Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

6
VK2-600PTZ User manual
2.6 IP Assignment
When VK2-600PTZ, encoder or decoder is first connected to the network it has no IP address.
So, it is necessary to allocate an IP address to the device with the “SmartManager” utility on the
CD.
1. Connect VK2-600PTZ / device to the network and power up.
2. Start SmartManager utility (All programs > NautilusClient16 > SmartManager), the main
window will be displayed, after a short while any network devices connected to the network
will be displayed in the list.
3. Select VK2-600PTZ on the list and click right button of the mouse.
You can see the pop-up menu as below.
4. Select Assign IP Address. You can seeAssign IP window. Enter the required IP address.
Note: For more information, refer to the SmartManager User’s Manual.

7
VK2-600PTZ User manual
2.7 Getting Started
Once installed apply power to VK2-600PTZ. It will start a configuration sequence.
OSD Position
The dome can move the OSD position in the OSD position setup.
(AREA TITLE) (AF AE)
(FUNC TITLE )
(CTRL KEY TO MOVE)
SAVE AND EXIT(ESC TO CANCEL)
(DOME ID…)
(ANGLE…)
OSD Position Setup
001 AF AE
EMPTY DATA
DOMEID:0001
W→360.0,090.0
INFORMATION
DISPLAY
FUNCTION
UNDER RUNNING
CAMERA TITLE
CAMERA ID
VIEW DIRECTION
PAN & TILT ANGLE
PRESET TITLE
AREA TITLE
STATUS of
FOCUS and AE

8
VK2-600PTZ User manual
Chapter 3 —Operation by Web Browser
The VK2-600PTZ can be used with Windows operating system and browsers.
The recommended browsers are Internet Explorer, Safari, Firefox, Opera and Google Chrome
with Windows.
Note: To view streaming video in Microsoft Internet Explorer, set your browser to allowActiveX
controls.
3.1 Access from a browser
1) Start a browser (Internet Explorer).
2) Enter the IP address or host name of the network camera in the Location/Address field of
your browser.
3) You can see a starting page. Click Live View or Setup to enter web page.
4) The encoder’s Live View page appears in your browser.

9
VK2-600PTZ User manual
3.2 Access from the internet
Access from the internet once connected, the network camera is accessible on your local
network (LAN). To access the video encoder from the Internet you must configure your
broadband router to allow incoming data traffic to the video encoder. To do this, enable the NAT
traversal feature, which will attempt to automatically configure the router to allow access to the
video encoder. This is enabled from Setup > System > Network > NAT Traversal.
For more information, please see NAT traversal (port mapping) for IPv4, on “3.5.5 System > 4)
Network > ⑥NAT Traversal”.
3.3 Setting the admin password over a secure connection
To gain access to the product, the password for the default administrator user must be set. This
is done in the “Admin Password” dialog, which is displayed when the network camera is
accessed for the setup at the first time. Enter your admin name and password, set by the
administrator.
Note: The default administrator username and password is “admin”. If the password is lost, the
network camera must be reset to the factory default settings.
Please see “3.8 Resetting to the factory default settings” for more details.
To prevent network eavesdropping when setting the admin password, this can be done via an
encrypted HTTPS connection, which requires an HTTPS certificate (see note below).
To set the password via a standard HTTP connection, enter it directly in the first dialog shown
below. To set the password via an encrypted HTTPS connection, please see Setup > System >
Security > HTTPS, on “3.5.5 System > 2) Security > ②HTTPS”.
Note: HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt the traffic
between web browsers and servers. The HTTPS certificate controls the encrypted
exchange of information.
3.4 Live View Page
The live view page comes in seven screen modes like 704x576(480), 704x288(240),
352x288(240), 176x144(120), 640x480, 320x240 and 160x120. Users are allowed to select the
most suitable one out of those modes. Please, adjust the mode in accordance with your PC
specifications and monitoring purposes.

10
VK2-600PTZ User manual
1) General controls
The video drop-down list allows you to select a customized or pre-
programmed video stream on the live view page. Stream profiles are
configured under Setup > Basic Configuration > Video & Image.
Please see “3.5.1 Basic Configuration” for more information.
The resolution drop-down list allows you to select the most suitable one
out of video resolutions to be displayed on live view page.
The protocol drop-down list allows you to select which combination of
protocols and methods to use depends on your viewing requirements, and
on the properties of your network.
The preset drop-down list allows you to select the preset number for the
PTZ camera being used. This icon is inactivated if the PTZ settings are not
set.
2) Control toolbar
The live viewer toolbar is available in the web browser page only. It displays the following
buttons:
The Stop button stops the video stream being played. Pressing the key again toggles
the start and stop. The Start button connects to the network camera or start playing a
video stream.
The Pause button pause the video stream being played.
The Snapshot button takes a snapshot of the current image. The location where the
image is saved can be specified.
The digital zoom activates a zoom-in or zoom-out function for video image on the live
screen.
The Full Screen button causes the video image to fill the entire screen area. No other
windows will be visible. Press the 'Esc' button on the computer keyboard to cancel full
screen view.
The Manual Trigger button activates a pop-up window to manually start or stop the
event.
The Camera Menu button activates a pop-up window for camera menu control.

11
VK2-600PTZ User manual
The PTZ button activates a pop-up window for Pan, Tilt and Zoom control.
Use this scale to control the volume of the speakers.
Use this scale to control the volume of the microphone.
Use this scale to control the volume of the speakers and microphones.
3) Camera Menu controls
If the network camera has been appropriately configured, the Live View page displays the
controls available for the OSD menu.
For more information, please see “Chapter 4 —Program and Operation”.
4) Pan/Tilt/Zoom controls
If the network camera has been appropriately configured, the Live View page displays the
controls available for the PTZ (Pan Tilt Zoom) or PT device installed. The administrator can
enable/disable the controls for specified users.
Please see “3.6 PTZ Control” for more information.
5) Video and Audio Streams
The network camera provides several images and video stream formats. Your requirements
and the properties of your network will determine the type you use.
The Live View page in the network camera provides access to H.264, MPEG-4 and Motion
JPEG video streams, and to the list of available video streams. Other applications and
clients can also access these video streams/images directly, without going via the Live View
page.
3.5 Network Camera Setup
This section describes how to configure the network camera, and is intended for product
Administrators, who have unrestricted access to all the Setup tools; and Operators, who have
access to the settings for Basic, Live View, Video & Image, Audio, Event, and System
Configuration.
You can configure the network camera by clicking Setup in the top right-hand corner of the Live
View page. Click on this page to access the online help that explains the setup tools.

12
VK2-600PTZ User manual
When accessing the network camera for the first time, the “Admin Password” dialog appears.
Enter your admin name and password, set by the administrator.
Note: If the password is lost, the network camera must be reset to the factory default settings.
Please see “3.8 Resetting to the Factory Default Settings”.
3.5.1 Basic Configuration
1) Users
User access control is enabled by default. An administrator can set up other users, by giving
these user names and passwords. It is also possible to allow anonymous viewer login, which
means that anybody may access the Live View page, as described below:
The user list displays the authorized users and user groups (levels):
User Group
Authority
Guest
Provides the lowest level of access, which only allows access
to the Live View page.
Operator
An operator can view the Live View page, create and modify
events, and adjust certain other settings. Operators have no
access to System Options.
Administrator
An administrator has unrestricted access to the Setup tools
and can determine the registration of all other users.
Enable anonymous viewer login: Check the box to use the webcasting features.
Refer to “3.5.2 Video & Image” for more details.

13
VK2-600PTZ User manual
2) Network
The network camera support both IP version 4 and IP version 6. Both versions may be
enabled simultaneously, and at least one version must always be enabled. When using IPv4,
the IP address for the video encoder can be set automatically via DHCP, or a static IP
address can be set manually. If IPv6 is enabled, the video encoders receive an IP address
according to the configuration in the network router. There is also the option of using the
Internet Dynamic DNS Service. For more information on setting the network, please see
Setup > System > Network, on “3.5.5 System > 4) Network”.
• Obtain IP address via DHCP: Dynamic Host Configuration Protocol (DHCP) is a protocol
that lets network administrators centrally manage and automate the assignment of IP
addresses on a network. DHCP is enabled by default. Although a DHCP server is mostly
used to set an IP address dynamically, it is also possible to use it to set a static, known IP
address for a particular MAC address.
• Use the following IP address: To use a static IP address for the network camera, check
the radio button and then make the following settings:
- IP address - Specify a unique IP address for your network camera.
- Subnet mask - Specify the mask for the subnet the network camera is located on.
- Default router - Specify the IP address of the default router (gateway) used for
connecting devices attached to different networks and network segments.
Notes:
1. DHCP should only be enabled if using dynamic IP address notification, or if your DHCP
server can update a DNS server, which then allows you to access the network camera by
name (host name). If DHCP is enabled and you cannot access the unit, you may have to
reset it to the factory default settings and then perform the installation again.
2. The ARP/Ping service is automatically disabled two minutes after the unit is started,
or as soon as an IP address is set.
3. Pinging the unit is still possible when this service is disabled.

14
VK2-600PTZ User manual
3) Video & Image
• Video Setting:
- Codec: The codec settings are separated into MPEG4 and H.264.
H.264 is also known as MPEG-4 Part 10. This is the new generation compression
standard for digital video.
This function offers higher video resolution than Motion JPEG or MPEG-4 at the same
bit rate and bandwidth, or the same quality video at a lower bit rate.
- Profile: There are 4 pre-programmed stream profiles available for quick set-up.
Choose the form of video encoding you wish to use from the drop-down list:
* H.264 MP(Main Profile): Primarily for low-cost applications that requires additional
error robustness, this profile is used rarely in videoconferencing and mobile
applications, it does add additional error resilience tools to the Constrained Baseline
Profile. The importance of this profile is fading after the Constrained Baseline Profile
has been defined.
* H.264 BP(Base Profile): Originally intended as the mainstream consumer profile for
broadcast and storage applications, the importance of this profile faded when the High
profile was developed for those applications.
* MPEG4 SP(Simple Profile): Mostly aimed for use in situations where low bit rate and
low resolution are mandated by other conditions of the applications, like network
bandwidth, device size etc.
* MPEG4 ASP(Advanced Simple Profile): Its notable technical features relative to the
Simple Profile, which is roughly similar to H.263, including "MPEG"-style quantization,
interlaced video, B pictures (also known as B Frames), Quarter Pixel motion
compensation (Qpel), Global motion compensation (GMC).
- Resolution: It enables users to determine a basic screen size when having an access
through the Web Browser or PC program. The screen size control comes in seven
modes like 4CIF(704x576(480)), 2CIF(704x288(240)), CIF(352x288(240)),
QCIF(176x144(120)), VGA(640x480), QVGA(320x240), and QQVGA(160x120). Users
can reset the selected screen size anytime while monitoring the screen on a real-time
basis.