Viper 9211VL User manual

Contents
Responder One.................................................................................................3
Basic Commands ..............................................................................................4
Remote Start.............................................................................................4
Unlock.....................................................................................................4
Shut Off the Remote Start...........................................................................5
Remote Control Configuration.............................................................................6
Remote Pairing .........................................................................................6
Remote Start Features ........................................................................................7
Disabling Remote Start ..............................................................................7
Remote and System Operations ..........................................................................8
Out of Range ...........................................................................................8
Battery Information....................................................................................8
Battery Replacement..................................................................................9
Government Regulations ..................................................................................10
Warning! Safety First.......................................................................................11
Limited Lifetime Consumer Warranty..................................................................13
9211VL 2012-07-11

3
© 2012 Directed. All rights reserved.
Responder One
Front
Elastomer
contact
Front
Elastomer
contact
Front
Elastomer
contact
+++
Circuit Board
Transmit
LED
Internal
Antenna
1
Transmit
LED
Internal
Antenna
1
Transmi
t
LED
Internal
Antenna
1
Feature Description
Internal Antenna Used for transmitting and receiving information
Transmit LED Transmit LED flashes once when transmitting and receiv-
ing information.
1Remote Start Press for one second to activate remote start.
1Shut down Remote Start Press and hold for 3 seconds to deactivate the remote
start.
1Unlock Press for one second to unlock. (Will only work if remote
start is active)

4© 2012 Directed. All rights reserved.
Basic Commands
Remote Start
Press and release the button.
Activates the remote starter. The remote responds with the remote start
On tone and the green LED on the remote flashes once. The vehicle's
parking lights turn ON constant to confirm remote start signal has been
received.
The runtime on the remote starter is predetermined based on vehicle
application. The remote starter will shut down when the preset runtime
times out or when any shutdown zone becomes active.
Note
Refer to the Quick Reference Guide for more information.
Unlock
Press and release the button.
Unlock function will only work when the vehicle is remote started. The
remote responds with 2 short beeps and the green LED on the remote
flashes once. The vehicle responds by flashing the parking lights twice
to confirm unlocking.

5
© 2012 Directed. All rights reserved.
Shut Off the Remote Start
Press and hold the button for 3 seconds.
The vehicle shuts down from the remote start mode. The remote plays
the remote start shut off tone and the orange LED flashes 1 time.
The remote starter will also shut down when the preset runtime times out
or when any shutdown zone becomes active.
Note
Refer to the Quick Reference Guide for more information.

6© 2012 Directed. All rights reserved.
Remote Control Configuration
Remote Pairing
The following instructions will step you through the remote pairing op-
eration.
1. Press and release the Integrated Programming Button (IPB) on the
XL202.
2. Within 5 seconds, press and hold the IPB. The status LED will flash
one time to confirm the system is ready for remote pairing.
3. Press the button, the remote will emit several tones to confirm pair-
ing is complete.
4. Release the IPB. Programming will exit by itself after 30 seconds
and the status LED turns off.
Note
Consult the installation center for the location of the XL202
or refer to dealer for programming.

7
© 2012 Directed. All rights reserved.
Remote Start Features
Refer to the Quick Reference Guide for more information on
remote start features that are specific to each vehicle.
Disabling Remote Start
Remote start can be disabled by moving the Toggle Switch to the Off
position. If remote start is attempted while Off, the engine will not start.
Move the switch back to the On position to resume normal operation.
Note
Consult the installation center for the location of Toggle
switch.

8© 2012 Directed. All rights reserved.
Remote and System Operations
Out of Range
Each time a command is performed the Responder One will expect a
command confirmation from the system. If a command confirmation is
not received a long fault tone plays as an alert.
Battery Information
Your remote is powered by two CR2016 cell batteries. When the bat-
teries weakens, the LED on the remote dims and operating range is
reduced.

9
© 2012 Directed. All rights reserved.
Battery Replacement
1. Using a small slotted screwdriver, in-
sert into slot located on the side of the unit
as shown and carefully pry the front of the
unit up, working your way around the edge
until the front is completely separated from the
housing.
Note: Make sure that the small elastomer con-
tact located inside the unit as shown does not
fall out during the replacement process.
2. Turn the circuit board over, remove
batteries from clip and replace.
Note: Verify that the battery polarity is
correct when replacing. Batteries are
stacked in series and polarity is indicated.
3. Reposition all parts and snap together.
Front
Elastomer
contact
Front
Elastomer
contact
Front
Elastomer
contact
+++
Circuit Board
Transmit
LED
Internal
Antenna
1
Transmit
LED
Internal
Antenna
1
Transmi
t
LED
Internal
Antenna
1
Front
Elastomer
contact
Front
Elastomer
contact
Front
Elastomer
contact
+++
Circuit Board
Transmit
LED
Internal
Antenna
1
Transmit
LED
Internal
Antenna
1
Transmit
LED
Internal
Antenna
1
Front
Elastomer
contact
Front
Elastomer
contact
Front
Elastomer
contact
+++
Circuit Board
Transmit
LED
Internal
Antenna
1
Transmit
LED
Internal
Antenna
1
Transmit
LED
Internal
Antenna
1

10 © 2012 Directed. All rights reserved.
Government Regulations
This device complies with Part 15 of FCC rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may cause undesirable
operation.
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment
generates and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television, which
can be determined by turning the equipment OFF and ON, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
This device complies with the Industry Canada Radio Standards Specification RSS 210. Its
use is authorized only on a no-interference, no-protection basis; in other words, this device
must not be used if it is determined that it causes harmful interference to services authorized
by IC. In addition, the user of this device must accept any radio interference that may be
received, even if this interference could affect the operation of the device.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this device.