Viper Responder One User manual

0 W N E R' S G U I D E

Contents
Government Regulations
....................................................................................
2
Warning!
Safety first ........
.................................................................................
3
What
is
Included
...........................................................................................
.
5
Important Information
.......................................................................................
.
5
Your
Warranty
.........................................................................................
.
5
System
Maintenance
................................................................................
.
5
Battery Replacement
..................................................................................
6
Using Your
System
...........................................................................................
7
Unlocking
................................................................................................
7
Car
Finder
...............................................................................................
7
Ignition Controlled Door locks
....................................................................
7
Remote
Start
.............................................................................................
8
Valet Take-Over
......................................................................................
1
0
Programming options
.......................................................................................
11
Glossary
of
Terms
............................................................................................
11
Quick Reference
Guide
....................................................................................
13
limited lifetime consumer warranty
....................................................................
15

Government
Regulations
This
device complies with
Part
15
of FCC
rules.
Operation
is
subject
to
the
fol-
lowing two conditions: (
1)
This
device may not cause harmful interference, and
(2)
This
device
must
accept any interference received, including interference that
may cause undesirable operation.
This
equipment
has
been tested and found
to
comply with
the
limits for a class B
digital device, pursuant
to
Part
15
of
the
FCC
Rules.
These
limits are designed
to
provide reasonable protection against harmful interference
in
a residential instal-
lation.
This
equipment generates and can radiate radio frequency energy and,
if not installed and
used
in
accordance with
the
instruction manual, may cause
harmful interference
to
radio communications. However, there
is
no guarantee
that interference will not
occu,·
in
a particular installation.
If
this
equipment does
cause harmful interference
to
radio or television, which can be determined by
turning
the
equipment
OFF
and
ON,
the
user
is
encouraged
to
try
to
correct
the
interference by one or more of
the
following measures:
• Re-orient or relocate the receiving antenna.
• Increase
the
separation between the equipment and receiver.
• Connect
the
equipment into an outlet on a circuit different from that
to which the receiver
is
connected.
• Consult
the
dealer or an experienced radio /
TV
technician for
help.
This
device complies with
the
Industry
Canada
Radio Standards Specification
RSS
21
0.
Its
use
is
authorized only
on
a no-interference, no-protection basis;
in
other words,
this
device
must
not be
used
if
it
is
determined that
it
causes harm-
ful
interference
to
services authorized by IC.
In
addition,
the
user
of
this
device
must
accept any radio interference that may be received, even if
this
interference
could affect
the
operation
of
the
device.
Warning:
Changes or modifications not expressly approved by
the
party
re-
sponsible for compliance could void
the
user's
authority
to
operate
this
device.
2 ©
2011 Directed Electronics. All rights reserved.

A
Warning!
Safety
first
The
following safety warnings
must
be observed at all
times:
Due
to
the
complexity of
this
system,
installation
of
this
product
must
only be
performed by an authorized Directed dealer.
When
properly installed,
this
system
can start
the
vehicle via a command signal
from
the
remote control transmitter. Therefore, never operate
the
system
in
an
enclosed area or partially enclosed area without ventilation
(such
as
a garage).
When
parking
in
an enclosed or partially enclosed area or when having
the
vehicle serviced,
the
remote start
system
must
be disabled using
the
installed
toggle switch.
It
is
the
user's
sole responsibility
to
properly handle and keep out
of reach from children all remote control transmitters to assure that
the
system
does not unintentionally remote start
the
vehicle.
THE
USER
MUST
INSTALL
A
CARBON
MONOXIDE
DETECTOR
IN
OR
ABOUT
THE
LIVING
AREA
ADJA-
CENT
TO
THE
VEHICLE.
ALL
DOORS LEADING FROM ADJACENT LIVING
AREAS
TO
THE
ENCLOSED
OR
PARTIALLY
ENCLOSED
VEHICLE
STORAGE
AREA
MUST
AT
ALL
TIMES
REMAIN CLOSED.
These
precautions are
the
sole
responsibility of
the
user.
Use
of
this
product
in
a manner contrary
to
its
intended mode of operation may
result
in
property damage, personal injury, or death. (
1)
Never remotely start
the
vehicle with
the
vehicle
in
gear, and
(2)
Never remotely start
the
vehicle with
the
keys
in
the
ignition.
The
user
must
also have
the
neutral safety feature of
the
vehicle periodically checked, wherein
the
vehicle
must
not remotely start while
the
car
is
in
gear.
This
testing should be performed
by
an authorized Directed
dealer
in
accordance with
the
Safety Check outlined
in
the
product installation
guide.
If
the
vehicle
starts
in
gear, cease remote start operation immediately and
consult with
the
authorized Directed dealer
to
fix
the
problem.
After
the
remote start module
has
been installed, contact your authorized dealer
© 2011 Directed Electronics. All rights reserved. 3

to
have
him
or
her
test
the
remote
start
module
by
performing
the
Safety
Check
outlined
in
the
product
installation
guide.
If
the
vehicle
starts
when
performing
the
Neutral
Safety
Shutdown
Circuit
test,
the
remote
start
unit
has
not
been
properly
installed.
The
remote
start
module
must
be
removed
or
the
installer
must
properly
reinstall
the
remote
start
system
so
that
the
vehicle
does
not
start
in
gear.
All
installations
must
be
performed
by
an
authorized
Directed
dealer.
OPERATION
OF
THE
REMOTE
START
MODULE
IF
THE
VEHICLE
STARTS
IN
GEAR
IS
CONTRARY
TO
ITS
INTENDED
MODE
OF
OPERATION.
OPERAT-
ING
THE
REMOTE
START
SYSTEM
UNDER
THESE
CONDITIONS
MAY
RESULT
IN
PROPERTY
DAMAGE
OR
PERSONAL
INJURY.
YOU
MUST
IMMEDIATELY
CEASE
THE
USE
OF
THE
UNIT
AND
SEEK
THE
ASSISTANCE
OF
AN
AU-
THORIZED
Directed
DEALER
TO
REPAIR
OR
DISCONNECT
THE
INSTALLED
REMOTE
START
MODULE.
DIRECTED
WILL
NOT
BE
HELD
RESPONSIBLE
OR
PAY
FOR
INSTALLATION
OR
REINSTALLATION
COSTS.
This
product
is
designed for fuel injected, automatic transmission
ve-
hicles only.
Use
of
this
product
in
a standard transmission vehicle
is
dangerous and contrary the product's intended
use.
4 © 2011 Directed Electronics. All rights reserved.

What
is
Included
•
The
control module
• Two 1-button transmitters
(P
/N
721 1
V)
• A push-button programming switch
•
Your
warranty card
• A shut-down toggle switch
Important
Information
Congratulations
on
the
purchase
of
your remote start
keyless
entry
sys-
tem.
This
system
has
been designed
to
provide years of trouble-free
operation.
By
carefully reading
this
owner's guide prior to using your
system,
you can maximize
the
use
of
this
system
and
its
features. Addi-
tional or replacement copies of
this
guide can be printed
by
accessing
the
Directed Electronics internet website at
www.directed.com.
Your
Warranty
Your
warranty card
must
be completely filled out and returned within
1
0 days of purchase.
Your
product warranty
is
not honored if your
warranty card
is
not returned.
Make
sure
that you receive
the
warranty
card
from
your dealer.
System
Maintenance
The
system
requires no specific maintenance.
Your
remote
is
powered
by two
CR20
16
cell batteries.
When
the
batteries weakens,
the
LED
on
the
remote dims and operating range
is
reduced.
© 2011 Directed Electronics. All rights reserved. 5

BaHery
Replacement
1. Using a small slotted screw-
driver, insert into slot located on
the
side
of
the
unit as shown and
carefully pry
the
front of
the
unit up,
working your
way
around
the
edge
until
the
front
is
completely separat-
ed from the housing.
Note:
Make
sure
that the small elas-
tomer contact located inside
the
unit
as
shown does not fall out during
the
re-
placement process.
2.
Turn
the
circuit board
over,
re-
move batteries from clip and replace.
Front
Elastomer
contact
Circuit Board
Note:
Verify that
the
battery polarity
is
correct when replac-
ing. Batteries are stacked
in
series and polarity
is
indicated.
3. Reposition all parts and snap together.
6
© 2011 Directed Electronics. All rights reserved.

Using Your System
Unlocking
Only after the vehicle is remotely started via the transmitter, press and
release
the transmitter button for 1 second to unlock the vehicle's doors.
The remote responds with 2 short beeps and the green LED on the re-
mote flashes once. The vehicle responds by flashing the parking lights
twice and honking
the horn twice to confirm unlocking.
Note: horn honk is an optional feature.
Cor Finder
Before the vehicle is remotely started via the transmitter, press and
hold
the transmitter button for 3 seconds to activate the car finder
function.
The vehicle responds by flashing the parking lights 5 times
slowly.
The remote responds with 1short beep and the orange LED on
the remote flashes once.
Ignition Controlled Door Locks
DRW-94
LOCK
~
I
If power door locks have been
connected to your
system, the doors
wi II lock three seconds after the
ignition is turned on, and unlock
when
the ignition is turned off.
© 2011 Directed Electronics. All rights reserved.
UNLOCK
7

Note:
In
order for
the
ignition controlled
door
locks to work, the feature
must
be turned on
in
programming.
Note:
If
the
ignition
is
turned on while the vehicle
is
remote started
the
doors
do
not lock until the remote start
shuts
off.
To
avoid being locked
out
of
the
vehicle,
do
not
turn
the
ignition on until you are ready to drive
the
vehicle.
Remote
Start
This
feature allows you to remotely start and
run
your vehicle for a
programmable period
of
time.
This
makes
it
possible to warm up the
engine,
as
well
as
adjust
the
interior temperature
of
the
vehicle with
the climate control
system.
If
interior heating or cooling
is
desired, the
climate controls
must
be preset, and the fan blower
must
be
set
to
the
desired level prior to remote starting the vehicle.
lmportantl
(l)
Never
remotely start
the
vehicle with
the
vehicle
in
gear, and
(2)
Never
remotely start
the
vehicle
with
the
key
in
the ignition.
;,,
,,,,,,,
,,,_,,,,,,., . .
....
,.,
..
' ·'
....
'
.,.
,.
--
,,
.....
,
..
..•
,.
.............
, . " ·"
''
"
"""
'
...
,
..
,
..
, ,
,,,
.•
,
..
,.,
..
.,
.
.,
,.,
. ,
....
,.
,.,
'
''"""·
.....
.,
..
,
.....
.
........
...
, ,
..
.,,
To
remote
start
the
vehicle:
l .
Press
the single button on the transmitter once.
2.
The
remote responds with the remote start
On
tones and the green
LED
on
the
remote flashes once.
The
vehicle's parking lights
turn
ON
constant to confirm remote start operation.
3.
Once
the vehicle has started, it
runs
for the pre-programmed pe-
riod
of
time (12,
24,
or
60
minutes) or until a shutdown input
is
triggered.
This
can be
set
to minute increments
by
your installer.
To
shut
off
the
remote
start:
While
the
vehicle
is
remote started press and hold
the
button on the
8 © 2011
Directed
Electronics.
All
rights
reserved.

remote for 3 seconds.
The
remote plays the remote start
shut
off tones
and the orange
LED
flashes 1 time.
The
vehicle
shuts
down
from
the
remote start mode.
2.
Press
the
brake pedal.
The
vehicle stays running
and
is
ready to drive.
Note:
If
the
brake pedal
is
pressed before the key
is
in
the
ON
position,
the
engine
shuts
down.
While
the
vehicle
is
running during remote start operation,
the
system
monitors
the
vehicle
and
automatically
shuts
down
the
engine if
the
system
receives
any
of
the following shut-down inputs:
• The brake pedal
is
pressed.
•
The
hood
is
opened.
• The shutdown toggle switch
is
put into
the
ON
position.
• The pre-programmed
run
time has elapsed.
•
The
single button
is
pressed and held for 3 seconds.
© 2011 Directed Electronics. All rights reserved.
9