Virgin HD-5 User manual

HD-5
Electronic Drum Kit
ASSEMBLY GUIDE
EASY ASSEMBLY GUIDE
IF YOU HAVE ANY QUESTIONS
CALL OUR TOLL FREE HELPLINE
888-998-9848
DO NOT RETURN TO THE STORE

1. Carefully unpack all contents of box
Not Pictured:
(1) Labeled Wiring Harness
(1) Pair Headphones
(1) Pair Drumsticks
(1) Drumstick Holder
Velcro Strips
Drum Frame
Cymbal Arms
Feet Hi-Hat Control Pedal
Kick
Pedal
Snare
Toms
Cymbals Sound
Module Module
Mount
Kick Drum
Kick Drum
Mount
UNBOXING YOUR DRUM KIT
(1) Hi-Hat Cymbal
(1) Crash Cymbal
(1) Ride Cymbal
(1) Sound Module
(1) Snare Drum
(3) Tom Drums
Kick Drum
Kick Pedal
Hi-Hat Control Pedal
Drum Kit Components

DRUM KIT ASSEMBLY
2. Attach the feet to the Drum Frame (g.1)
(g.1)
3. Unfold the Drum Frame arms as shown
(g.2)
(g.2)
(g.3)
4. Attach the cymbal arms to the drum frame
indicated positions . (g.3)
(g.4)
CRASH
RIDE
HI-HAT
5. Attach the cymbals to the cymbal arms as
shown. Place the n on the cymbal arm between
the anges on the cymbal as shown. (g.4)

BACK
SNARE
TOM
(g.5)
(g.6)
DRUM KIT ASSEMBLY (CON’T)
(g.7)
SNARE
TOM
7. Attach the Drum Pads in the positions
hown below. (g. 5)
6. Align the holes in Snare Drum Pad and the
three Tom Drum Pads and insert them into the
pole on the Drum Frame as shown.
8. Align the holes and attach the screws
with the Drum Sound Module head
and its stand as shown below. (g. 6)
9. Insert the rod of sound module stand into
the Drum Frame clamp as shown, then tight-
en. (g.7)

12. Attach the kick drum pedal mallet to the
kick drum pedal by insertIng and attaching as
shown below. (g.10& 11)
(g.8)
(g.9)
(g.10)
DRUM KIT ASSEMBLY (CON’T)
(g.11)
(g.13)
(g.12)
11. Assemble the kick drum pedal by inserting
the two chrome metal rods into the kick drum
pedal frame as shown below . (g.9)
10. Attach the kick drum to the kick drum
brace as shown below. (g.8)
13. Insert the tongue of the kick drum into the clamp of
the kick drum pedal. (g.12) Tighten clamp on the ped-
al until the kick drum and pedal are securely fastened.
(g.13)

plug into “trigger”
control module
cable snake
to drumset
POWER
OFF ON
DC 9V
USB TRIGGER
HEADPHONE
LINE OUT LINE IN
Drum Module Connector Panel
DRUM KIT WIRING DIAGRAM
POWER
OFF ON
DC 9V
USB
TRIGGER
HEADPHONE
LINE OUT LINE IN
kick
high-hat control
snare
hi-hat
crash
tom 1
tom 2
tom 3
ride
CARPET
HARD FLOORING
PEEL
(g. 14)
(g. 15)
DRUM KIT ASSEMBLY (CON’T)
14. Check the surface pads on the bottom of the
hi-hat control pedal. The pads may be used on
either carpet or hard ooring. (g.14)
15. Place the hi-hat control pedal on the
ground by the hi-hat cymbal. (g.15)
16. Connect the wiring harness to the interface at the bottom of the drum sound module, then
connect the labeled cables to their corresponding drum pads, cymbals and pedals, as show
below.

17. Extend the drum throne legs and secure the legs with the wingut. (g 16) Fasten the drum
throne stool to the height adjustment rod and secure the stool with the wingnut. (g 17) Set
up the drum throne at the desired height as shown below. (g 18)
18. Attach Drumstick Pouch (g 19) to drum frame as shown. (g 20)
DRUM THRONE ASSEMBLY
(g. 18)
(g. 17)(g. 13)(g. 16)
FINAL STEPS
POWER
OFF ON
DC 9V
USB
TRIGGER
HEADPHONE
LINE OUT LINE IN
velcro
drum frame
20. Attach the included power supply adapter
and the headphones to drum sound module
connector panel.
19. Please use the included Velcro Strips to attach
the wiring harness to the drum frame. This will
help to make the wiring harness neat and orderly
against the drum frame.
(g 19)
(g 20)

Virgin Musical Instrument Company
PO BOX 2908
LA MESA, CA 91943
[e-mail]
www.virginmusicalinstruments.com
Virgin (VMI) is the Parent Company of Hitman Drums
If you have any questions about your drum kit
please contact us toll free 888-998-9848