VIRTUFIT Premium Trampoline with Safety Net User manual
User Manual
EN
�
�
�
�
�
�
�
Premium Trampoline with Safety Net
EN Virtufit Premium Trampoline with Safety Net
2
SAFETY INSTRUCTIONSSAFETY INSTRUCTIONS
CHECKLISTCHECKLIST
ASSEMBLY INSTRUCTIONSASSEMBLY INSTRUCTIONS
MOVING THE TRAMPOLINEMOVING THE TRAMPOLINE
MAINTENANCEMAINTENANCE
BASIC TRAMPOLINE SKILLSBASIC TRAMPOLINE SKILLS
3 - 5
6 - 7
8 - 18
19
20
21
INDEX
EN
Virtufit Premium Trampoline with Safety Net 3
SAFETY INSTRUCTIONS
– Recommended age 6+ years.
– No somersaults or flips - can cause serious injury. Jump without shoes.
– Not suitable for children under 36 months - small parts, choking hazard.
– The trampoline is intended for outdoor use only.
– Only one user at a time. Danger of Collision hazard.
– Always close the net opening before jumping.
– Do not use the mat when it is wet
– Empty pockets and hands before jumping
– Always jump in the middle of the mat
– Do not eat while jumping. It is advisable not to bounce immediately after a meal.
– Do not exit by a jump
– Do not use in strong wind conditions and secure the trampoline.
– The trampoline shall be assembled by an adult in accordance with the assembly instructions and
thereafter checked before the first use.
– The max user weight is: 244 cm: 70 KGS - 305 cm: 120 KGS - 366 cm: 150 KGS.
– Limit the time of continuous usage (make regular stops).
ATTENTION
WARNING:
Consult your child’s doctor before jumping, especially for children with health problems.
Read all instructions before using the trampoline. VirtuFit takes no responsibility for
any injuries or material damage caused by the use of this product. Read the manual
carefully before you start to assemble and/or use the trampoline. Adult supervision is
required at all times.
EN Virtufit Premium Trampoline with Safety Net
4
– This trampoline is not intended to be buried in the ground.
– The trampoline must be placed on a level surface at least 2m from any structures or obstructions
such as fence, garage, house, overhanging branches, laundry lines or electrical wires.
– Do not install the trampoline over concrete, asphalt or any other hard surface. Also not in proximity
of other conflicting installations, such as padding / swimming pools, swings, slides or climbing
frames.
– Any modifications made by the consumer to the original trampoline (e.g. the adding of an accessory)
shall be carried out according to the instructions of the manufacturer.
– Inspect trampoline / enclosure net before each use.
– If an access ladder is used it should be removed when trampoline is not in use.
– Make sure there are no children / animals / obstructions underneath the trampoline.
– Access the trampoline through the door of the enclosure net only. Making sure you securely close it
before bouncing. Use: Ensure the door is securely closed before bouncing.
– Don’t intentionally rebound off the enclosure net as this will weaken it.
– Only attach manufacturer approved accessories to the trampoline and enclosure net.
– Always jump in the middle of the mat and practice bounce techniques safely with adult supervision
and guidance.
–
–
–
–
–
–
–
–
–
–
Warranty claim is excluded if the cause of the defect is the result of:
– Maintenance assembly and repair work not performed by an official dealer.
– In case of improper use, neglect and / or poor maintenance.
– Failure to maintain the fitness equipment in accordance with the manufacturer’s instructions.
– The product has been incorporated into the soil.
– Defects caused by external influences (eg climate and weather influences).
�
�
�
�
�
�
�
�
���
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
SAFETY INSTRUCTIONS
ADVISORY
EN
Virtufit Premium Trampoline with Safety Net 5
SAFETY INSTRUCTIONS
– Attention to the need to carry out checks and maintenance of the main parts (frame, suspension
system, mat, padding, and enclosure) at the beginning of each season and also at regular intervals
of every 2 weeks, pointing out that if these checks are not carried out, the trampoline could become
dangerous.
– Check all nuts and bolts for tightness and tighten when required.
– Check that all spring-loaded (pit pin) joints are still intact and cannot become dislodged during play.
– Check all coverings and sharp edges and replace when required.
– Retain the maintenance instruction manual.
– Outdoor trampolines should be equipped with a device that in strong wind conditions avoid
displacement due to wind (e.g. steel bars in the ground or loads like sand bag or water bags) and/or
items catching wind like net and mat should be removed.
– In certain countries during winter period, the snow load and the very low temperature can damage
the trampoline. It is recommended to remove the snow and store the mat and the enclosure indoor.
– Check that mat, padding, enclosure and soft surface are without defects.
– Make sure that the hook-and-loop fasteners are closed correctly during use of trampoline!
– Trampoline and net should be packed away in winter. Make sure all parts are dry and packed securely.
– Store dry to support product longevity. Always be aware of wear and tear due to weather and wind.
– We recommend securing the trampoline in strong winds. Tie the trampoline down with ropes
attached to the trampoline pad. Tie the trampoline down in a minimum of three places distributed
evenly across the trampoline frame.
– Do not secure the legs as these may become misaligned and ruin the trampoline. Dismantle or
remove the trampoline completely, if required. It may result in great danger if the trampoline is not
secured in strong winds.
– If the trampoline is not used for short periods of time and to avoid jump mat debris caused by fallen
leaves and twigs, It’s recommended usage of a Weather Cover. When the trampoline is not used for a
longer period of time (e.g. during the winter). It’s recommended storing the trampoline, especially
the protective padding, in a dry area to support product longevity.
NOTE! Sunlight, rain, snow and extreme temperatures reduce the strength of these parts over time.
ASSEMBLY AND MAINTENANCE INSTRUCTIONS
EN Virtufit Premium Trampoline with Safety Net
6
When you open the carton, and you will find the below parts in the carton. Place all
parts on the floor. Make sure you have all the parts listed. If parts are missing, please
contact the supplier.
TOOLKIT
CHECKLIST
#DESCRIPTION 244
CM 305
CM 366
CM
AFrame Cover 1 1 1
BJumping Mat 1 1 1
CTop Rail 6 6 8
DT-Connector 6 6 8
ESpring 48 60 72
FLeg Extension 0 6 8
GW-Shaped Leg 3 3 4
HSpring Tool 1 1 1
ILong Screw 0 6 8
JScrewdriver 0 1 1
�
�
�
�
�
�
�
�
�
�
EN
Virtufit Premium Trampoline with Safety Net 7
#DESCRIPTION 244
CM 305
CM 366
CM
KBottom Tube 6 6 8
LTop Tube 6 6 8
MTop Cap 6 6 8
NFork Screw 6 6 8
OEnclosure Net 1 1 1
PFiberglass Rod 6 6 8
QSleeve 6 6 8
RSpanner 1 1 1
SBungee Cord 6 6 8
T9-Shaped Screw 6 6 8
UScrew 6 6 8
TOOLKIT
CHECKLIST
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
EN Virtufit Premium Trampoline with Safety Net
8
Missing parts: If you think you are missing certain parts in your package, carefully check the styrofoa and
the trampoline. Some parts (bolts, screws, etc.) are already attached to/in the trampoline.
Use gloves to protect your hands from bottlenecks during assembly. When you’re ready to get started,
make sure you have plenty of room and a clean, dry area for mounting.
Read the assembly instructions below before you start mounting the trampoline. Incorrect mounting
will damage the trampoline frame:
• Make sure the trampoline is placed on level ground. Uneven ground surfaces may cause the
trampoline frame to warp (FIG 1).
• Make sure that all bolts holding the frame joints are tightened completely before installing the
springs. Failure to do this properly will cause the frame to warp.
• Make sure NOT to use one’s leg to push against the trampoline leg or frame when loading the springs.
It will cause the trampoline to warp (FIG 2).
• DO NOT load the springs onto the frame on only one side of the trampoline. Uneven distribution of
tension from the springs will cause the frame to warp (FIG 2).
• If the trampoline frame warps up, do not be alarmed as the “Quad-lock” system is designed to be
flexible. Push down on the part of the frame that warped with two people as shown. The frame will
level out (FIG 3).
NOTE! For the next assembly 2 adults in good physical condition are required. Wear good shoes and
keep balance to avoid a fall. Failure to follow all instructions and warnings exactly could result in
serious injury.
ASSEMBLY INSTRUCTIONS
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
FOTO 1
FIGUUR 7
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
FOTO 2
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
FOTO 3
EN
Virtufit Premium Trampoline with Safety Net 9
ASSEMBLY INSTRUCTIONS
STEP 1
• By attaching two Leg Extension (F) to W-shaped Legs(G), to form a “U” shaped with Screws(I) by
Screwdriver(J). Repeat this step with the remaining pieces to make the rest U legs. Leave to one side
when finished
NOTE! 8FT is without leg extension. This step is only suitable for 10FT and 12FT.
�
� �
�
�
��� �
�
EN Virtufit Premium Trampoline with Safety Net
10
ASSEMBLY INSTRUCTIONS
• Begin by attaching Top Rails (C) to T-connectors (D). Continue until you form a large circle.
NOTE! Have a second person or use a wall to apply some resistance against the frame to help it
shift into place.
• Two people will be necessary at this point to assemble the trampoline. One person lifts up the circle
frames. The other person lifts the W shaped leg tubes to a standing (vertical) position and inserts the
T-connectors into a U shaped leg tubes. Ensure the locking holes are aligned.
�
� �
�
�
��� �
�
�
� �
�
�
��� �
�
EN
Virtufit Premium Trampoline with Safety Net 11
STEP 2
NOTE! 2 adults may be required to complete placement of all springs. Springs will create high
levels of tension when assembled. Please take care not to pinch your fingers.
• Lay out the Jumping Mat(B) inside the frame.
• Take Spring (D) and insert end (b) into Top rail tube, then put end (a) of the spring into trampoline
Jumping Mat (B) rings.
• Hold Spring Tool (H) overhand and pull spring hook towards Top rail (C) as picture shown; drop hook
into frame hole until it latches on completely, tap it down if hook is not completely in the hole.
�
�
�
�
�
��
�
�
�
�
�
��
�
�
�
�
�
��
ASSEMBLY INSTRUCTIONS
EN Virtufit Premium Trampoline with Safety Net
12
�
�
ASSEMBLY INSTRUCTIONS
IMPORTANT
• Springs must be attached the right way around and fully inserted into the holes along the top of the
frame.
• It is easier to place one hand on the frame and pull the spring towards you.
• Make sure that (a) is attached to the D-rings of the jumping mat and (b) is attached to the trampoline
frame.
• The placement of the next spring must be on the opposite side of frame, then center adjacent, then
opposite. It must be done this way so the tension of the spring is spread equality.
• To ensure that you have started to fit the bed correctly, please count the spring holes in between
each top rail to make sure that you have the same number of spring holes in the top rails.
• Make sure that the D-rings on the bed, match the number of holes along the top rails.
• If you notice that you have skipped a hole and D-ring connection, recount, remove and adjust
accordingly.
Installing the Protective Edge:
• Lay Frame Cover (A) on outer edge, so springs are covered. It should be fitted like a shower cap. It
should be fitted like a shower cap. Please ensure it covers all metal parts.
• Tie the strap located at the under side of the Frame Cover to frame. Do not tie them to the springs.
EN
Virtufit Premium Trampoline with Safety Net 13
STEP 3
• Connect the Bottom Tube (K) to the Top Tube (L).
NOTE! There are sunken Dots at the end of Top Tubes.
• Align the hole in the bottom tube with the slot in the top tube, screw one of the screws through the
slot in the top tube and into the hole in the bottom tube using the screwdriver.
• Insert the Pole Tube into the Sleeves (Q) as above picture shown.
�
��
� �
�
��
� �
�
��
� �
ASSEMBLY INSTRUCTIONS
EN Virtufit Premium Trampoline with Safety Net
14
• Firmly fix the Bottom Tube (K) to the leg extension with the Fork Screw (N) & 9 Shaped Screws (T),
then fasten them by Spanner (R).
�
�
�
�
�
ASSEMBLY INSTRUCTIONS
EN
Virtufit Premium Trampoline with Safety Net 15
STEP 4
ASSEMBLY INSTRUCTIONS
• Slide the Fiberglass Rod(P) into the passage sewn on the top of the safety net(O), then push the
Fiberglass Rod into the Top Cap(M), as shown in the pictures above.
• Repeating with the remaining rods until they all connect. To make the last connection, have one
person stand on the opposite side from you, push the rods towards the centre of the ring until they
are in line with each other and make the last connection, as shown in the picture above
• Raise the net up into position and clip the ring into the Top tubes (L).
�
�
�
�
�
�
�
�
�
�
�
�
�
�
EN Virtufit Premium Trampoline with Safety Net
16
• Connect two pieces of upper Velcros (along the top of Sleeve) to Top Caps (M).
• Lastly, run each Bungee Cord (S) through the loop(sewn on the bottom of the safety net), then
attached the Bungee Cords to the Bottom Pole tubes as figure shows.
After assembling the trampoline, it is important that you perform the following safety checks:
• Ensure all screws and bolts are tightly secured.
• Look under the trampoline and check all springs are hooked securely to the frame and jumping mat
rings.
• Inspect the spring cover and check it is covering the springs and frame and that it is tied securely.
The VirtuFit Premium Trampoline with Safety Net is now complete and ready to use!
�
�
�
�
�
�
�
�
ASSEMBLY INSTRUCTIONS
EN
Virtufit Premium Trampoline with Safety Net 17
TOOLKIT LADDER
LADDER ASSEMBLY
ASSEMBLY INSTRUCTIONS - LADDER
• Place the two frame legs (2) in a free space. Then place one of the ladder steps (1) on the bottom of
each frame leg. Then slide the step up to the top bolt holes of the legs and the steps. NOTE! Make
sure the diamond pattern of the stairs is facing up is targeted.
• Insert two bolts (4) through the ladder step (1) and the frame legs (2). Then tighten a nut (3) to the
back of each bolt with a screwdriver (J).
• Repeat steps 1 and 2 to assemble the second ladder step.
• Place the lower base frame (5) on the frame legs of the ladder (2), making sure that the screw holes
are aligned.
• Insert two short screws (6) through the lower base frame (5) and the frame legs (2). Turn then tighten
each short screw with a screwdriver (J).
• Test the steps to ensure they are properly attached.
• Find the net opening of your safety net. Lift your protective edge and transfer the hooks from the
ladder the curved frame of the trampoline. Pull out the ladder at the base of the trampoline to make
sure it hits the ground as far away from the trampoline frame as possible.
#DESCRIPTION QTY
1Ladder Step 2
2Frame Leg 2
3Nut 4
4Bolt 4
5Lower Frame Base 1
6Shot Screw 2
EN Virtufit Premium Trampoline with Safety Net
18
ASSEMBLY INSTRUCTIONS -LADDER
• Test the steps to ensure they are properly attached.
• Find the net opening of your safety net. Lift your protective edge and transfer the hooks from the
ladder the curved frame of the trampoline. Pull out the ladder at the base of the trampoline to make
sure it hits the ground as far away from the trampoline frame as possible.
EN
Virtufit Premium Trampoline with Safety Net 19
MOVING THE TRAMPOLINE
INSTRUCTIONS
• Moving trampoline. If the trampoline and enclosure needs to be moved, it should be moved by two
persons at least, kept horizontal, and lifted slightly.
• If necessary, the trampoline and enclosure can be taken for moving. To take the trampoline apart,
follow the assembly steps in reverse order.
• If you need to move the trampoline, two people should be used at least.
• All connector points should be wrapped secured with weather resistant tape, such as duct tape.
This will keep the frame intact during the move and prevent the connector points from dislocating
and separating.
• When moving, lift the trampoline slightly of the ground and keep it horizontal to the ground. For any
type of other move, you should disassemble the trampoline.
EN Virtufit Premium Trampoline with Safety Net
20
SEMI-ANNUAL MAINTENANCE
DAILY MAINTENANCE
– Clean and remove sweat / moisture after each use. Do not use aggressive cleaning agents
– Check that the trampoline is free from dust and dirt.
– Inspect all bolts and nuts related to the trampoline, tighten as required.
MAINTENANCE
This manual suits for next models
1
Table of contents
Other VIRTUFIT Sport & Outdoor manuals
VIRTUFIT
VIRTUFIT Soccer Goal Pro User manual
VIRTUFIT
VIRTUFIT PREMIUM User manual
VIRTUFIT
VIRTUFIT VF06020 User manual
VIRTUFIT
VIRTUFIT Mini Basketball Hoop with Ball and Pump User manual
VIRTUFIT
VIRTUFIT Foldable Fitness Trampoline User manual
VIRTUFIT
VIRTUFIT Surfer 305 User manual
VIRTUFIT
VIRTUFIT VF06003 User manual
VIRTUFIT
VIRTUFIT VF06007 User manual
VIRTUFIT
VIRTUFIT Soccer Goal Pro User manual
