VISIO V Power VP-60 User manual

NO.008
V Power
VP-60 VP-120
User Manual
Please read the instructions carefully before use

VP-60/120
1-
TABLE OF CONTENTS
1. Safety Instruction
2. Features
3. Technical Specification
4. Installing Instructions
5. Main Function
6. Overview
6.1 Front View
6.2 Rear View
7. DMX Controller
8. DMX512 Configuration
9. DMX512 Connection
9.1 XLR Connection
9.2 RJ45 Connection
EC - Declaration of Conformity
We declare that our products (lighting equipments) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
EN55014-2: 1997 A1: 2001, EN61000-4-2: 1995; EN61000-4-3: 2002;
EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6: 1996,
EN61000-4-11: 1994.
&
Harmonized Standard
EN60598-1: 2000+ALL: 2000+A12: 2002
Safety of household and similar electrical appliances
Part 1: General requirements

VP-60/120
17-
9.1 RJ45 Connection
DMXInput,Output LEDmoduleInput
RJ45 Connector RJ45 Connector
Front view of the Connector Front view of the Connector
Pin 1: Not connected Pin 5: Not connected Pin 1: Red LED + Pin 5: Red LED -
Pin 2: Not connected Pin 6: Data+ Pin 2: Green LED + Pin 6: Green LED -
Pin 3: Not connected Pin 7: Data- Pin 3: Blue LED + Pin7:Blue LED -
Pin 4: Not connected Pin 8: GND Pin 4: White LED + Pin 8: White LED -
VP-60/120
2-
1. Safety Introductions
Please read the User Manual carefully as it includes important information regarding
details of operation, maintenance and technical data. Keep this manual with unit for
future consultation.
WARNING！
●Avoiding any flammable liquids, water or metal objects enter into the unit.
●If any liquid spill on the unit, disconnect the power supply immediately.
●When serious operation problem happen, stop using the unit immediately and
contact your local dealer for service.
●Do not open the unit because there are no user serviceable parts inside.
●Never try to repair the unit yourself. Repairs by unqualified people could cause
damage or faulty operation. Please contact your nearest dealer for any service.
CAUTION！
●After removed the package, make sure the unit is not damaged in any way. Don’t
use it with doubt and contact an authorized dealer.
●Never use the unit under the excessive humidity and a temperature over 40℃.
●Do not try to dismantle or modify the unit.
2. Features
●7 Channel modes enables V Power to control passive lighting fixtures that fitted with
different LED emitters.
●Comes with 16 built-in programs under Master/Slave mode. 3 user editable chases,
each chase up to 50 (VP-60) or 42 VP-120）scenes.
●Under Manual mode, user can adjust each color’s intensity to get the best color
mixing effects.
●White Balance setup-User can adjust the pre-set White Balance of the V Power.
●Smooth fade in/fade out effect.
●It can be controlled by the LED Remote Commander (LED-RC).
●LED display for easy navigation.

VP-60/120
3-
3. Technical Specifications
yDMX Input
Control: DMX 512
DMX connection: RJ45 or 3 pin XLR
yDMX Output
Max. Power Output:60W（VP-60）/ 120W(VP-120)
Output Voltage: DC 48V
Max. Output Current: 350mA per color
Max. Load per zone: RGB & RGBW mode-Each color 12 LEDs max.
White mode-Each white 24 LEDs max.
yInput Voltage: 100V-240V~50-60Hz
yFuse: T 1A（VP-60）
T 2A（VP-120）
yDimension: 215×179×61 mm (VP-60)
279×234×61 mm (VP-120)
yWeight：1.2kgs (VP-60)
2.1kgs (VP-120)
VP-60/120
16-
9. DMX512 Connection
9.1 XLR Connection
1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin
adapter-cable.
2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120
ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug
and plug it in the DMX-output of the last unit.
3. Connect the unit together in a `daisy chain` by XLR plug from the output of the unit
to the input of the next unit. The cable can not branched or split to a `Y` cable.
DMX 512 is a very high-speed signal. Inadequate or damaged cables, soldered
joints or corroded connectors can easily distort the signal and shut down the
system.
4. The DMX output and input connectors are pass-through to maintain the DMX
circuit, when one of the units’ power is disconnected.
5. Each unit needs to have an address set to receive the data sent by the controller.
The address number is between 0-511 (usually 0 & 1 are equal to 1).
6. The end of the DMX 512 system should be terminated to reduce signal errors.
7. 3 pin XLR connectors are more popular than 5 pin XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+),
Pin 4/Pin 5: not used.

VP-60/120
15-
VP-60/120
4-
4. Installing instructions
The VP-60/120 should be placed on a non-flammable flat surface in any orientation
and fixed by the two screws. There are two mounting holes on the housing. Ensure
that installation place is enough ventilated.
V Power could control the LED fixtures such as V Aqua, V Bar, V Ceiling, V Inground,
V Net, V Wall and CW36, the VP-60 power output is 60 watt and the VP-120 power
output is 120 watt.

VP-60/120
5-
5. Main Function
To select any function, press MENU button until the required one is shown on the
display. Select the function by ENTER button and the display will blink. Use DOWN
and UP button to change the mode. Once the required mode has been selected,
press ENTER button to setup (or it will automatically return to the main functions
without any change after idling one minute). Back to the functions without any change
press MENU button. The main functions are shown below:
VP-60/120
14-

VP-60/120
13-
VP-120:
VP-60/120
6-
DMX 512 Address Setting
Press the MENU button up to when the is shown on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to change the
DMX 512 address from 1 to 512. Once the address has been selected, press ENTER
button to setup (or automatically return to the main functions without any change after
idling one minute). Back to the previous function without any change press MENU
button.
Channel Mode
Press the MENU button up to when the is shown on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(11 channels) or (8 channels)…or (2 Channels) mode.
Once the mode has been selected, press the ENTER button to setup (or automatically
return to the main functions without any change after idling one minute). To go back to
the previous function without any change press the MENU button.
Show
Press the MENU button up to when the is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(show 1) or … or (show 19) . Once the show has been
selected, press the ENTER button and use DOWN and UP button to set fade time
(0-255: 0.256s-66847s) and wait time(0-255:0.256s-66847s), once selected, press
ENTER button to store (or automatically return to the main functions without any
change after idling one minute). To go back to the previous function without any
change press the MENU button.
Blackout Mode
Press the MENU button up to when the is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(yes blackout) or (no blackout) mode. Once selected, press the
ENTER button to setup(or automatically return to the main functions without any
change after idling one minute). To go back to the previous function without any
change press the MENU button.

VP-60/120
7-
Program Show
Press the MENU button up to when the is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(show 17) or （show 18）or (show 19). Once the show has
been selected, press the ENTER button to enter setting program. You can select
(length, the steps, you choose from the total amount of steps, you want to run,
for example, if the total amount of steps you set is 42, you can choose only first 1-10
steps to run). (step), select to set or ,
(color: 0-255, 1 for zone 1, 2 for zone 2 ), or , (white) and
or , (dimmer) for every step. Automatically return to the main
functions without any change after idling one minute. To go back to the previous
function without any change press the MENU button.
NOTE: For VP-120, when you selected channel mode 5 or 6, you can set only
, (color, 1 for zone 1, 2 for zone 2) and ,
(dimmer) for every step. When you selected channel mode 7, you can set only
, (dimmer) for every step.
Manual Mode
Press the MENU button up to when the is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
or , (red, 1 for zone 1, 2 for zone 2 ), or ,
（green）, or , (blue), or ,
(white), or (dimmer), (strobe) mode. Once selected, press
the ENTER button to setup (or automatically return to the main functions without any
change after idling one minute). To go back to the previous function without any
change press the MENU button.
Adjust White Balance
Press the MENU button up to when the is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
or , (red: 0-255, 1 for zone 1, 2 for zone 2 ), or
VP-60/120
12-
8. DMX512 Configuration
VP-60:

VP-60/120
11-
11 Channels:
8 Channels:
6 Channels:
7 Channels:
4 Channels:
3 Channels:
2 Channels:
1 Channel:
VP-60/120
8-
, （green）, or , (blue) mode. Once selected,
press the ENTER button to store (or automatically return to the main functions without
any change after idling one minute). To go back to the previous function without any
change press the MENU button.
Self-Test
Press the MENU button up to when the is blinking on the display. Pressing
ENTER button and the unit will run self-test by built-in program. To go back to the main
functions press the MENU button again.
LED
Press the MENU button up to when the is shown on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(LED display ON) or ( LED display OFF) mode. Once selected, press
ENTER button to setup (or automatically return to the main functions without any
change after idling one minute). To go black to the previous function without any
change press MENU button.
Fixture Hours
Press the MENU button up to when the is blinking on the display. Pressing
ENTER button and the display will show the number of working hours of the unit. To
go back to the main functions press the MENU button.
Software version
Press the MENU button up to when the is blinking on the display. Pressing
ENTER button and the display will show the version of software of the unit. To go back
to the previous function press the MENU button.

VP-60/120
9-
6. Overview
6.1 Front View
LED
1. DMX On DMX Input
2. MASTER On Master Mode
3. SLAVE On Slave Mode
4. POWER On Power on
5. Display To show the various menu and selected function
6. Menu Press the button to select the programming functions.
7. Down Press the button to go backward for the desired functions.
8. Up Press the button to go forward for the desired functions.
9. Enter Press the button to confirm the selected functions.
VP-60/120
10-
6.2 Rear View
VP-60:
VP-120
1. POWER Power cable for AC input
2. FUSE For protecting the unit when the transient current is too big
3. DMX OUT DMX Output RJ45 or 3 pin XLR socket
4. DMX IN DMX input RJ45 or 3 pin XLR socket
5. LED DC power & signal output for linking LED fixtures
7. DMX Controller
Using universal DMX controller to control the units, you have to set DMX address from
1 to 512 so that the units can receive DMX signal.
Press the MENU button up to when the is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to change the
DMX512 address. Once the address has been selected, press ENTER button to store
(or it will automatically return to the main functions without any change after idling one
minute). To go back to the main functions without any change press the MENU button.
Please refer to the following diagram to address your DMX512 channel for the first 4
units.