Vision ZA1502IN-7 User manual

www.visionsecurity.com.tw
Installation & Operation Manual
Product Description and Specification:
Limited Warranty
Vision Guarantees that every wireless 2 in 1 Universal Remote is free from
physical defects in material and workmanship under normal use for one
year from the date of purchase. If the product proves defective during this
one-year warranty period, Vision will replace it free of charge. Vision does
not issue any refunds. This warranty is extended to the original end user
purchase only and is not transferable. This warranty does not apply to: (1)
damage to units caused by accident, dropping or abuse in handling, or any
negligent use; (2) units which have been subject to unauthorized repair,
taken apart, or otherwise modified; (3) units not used in accordance with
instruction; (4) damages exceeding the cost of the product; (5) transit
damage, initial installation costs, removal cost, or reinstallation cost. For
information on additional devices, please visit us at
www.visionsecurity.com.tw
Federal Communications Commission Statement
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
FCC Caution
“the user that changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
the equipment.”
FCC Statement in User’s Manual (for calss B) FCC Section 15.105
“Federal Communications Commission (FCC) Statement”
This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Z-Wave Command Classes:
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_BATTERY
COMMAND_CLASS_CONFIGURATION_V4
COMMAND_CLASS_DEVICE_RESET_LOCALLY
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5
COMMAND_CLASS_INDICATOR_V3
COMMAND_CLASS_NOTIFICATION_V8
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SECURITY_2
COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_TRANSPORT_SERVICE_V2
COMMAND_CLASS_VERSION_V3
COMMAND_CLASS_WAKE_UP_V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Z-Wave S2 Support Command Classes :
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_BATTERY
COMMAND_CLASS_CONFIGURATION_V4
COMMAND_CLASS_DEVICE_RESET_LOCALLY
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5
COMMAND_CLASS_INDICATOR_V3
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
COMMAND_CLASS_NOTIFICATION_V8
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_VERSION_V3
COMMAND_CLASS_WAKE_UP_V2
ZA 1502-7 V0 1091224
2 in 1 Universal Remote
ZA1502IN-7
ZA1502EU-7
ZA1502RU-7
ZA1502US-7
ZA1502IL-7
ZA1502KR-7
ZA1502HK-7
ZA1502JP-7
ZA1502BR-7
Specification: Package Content
Protocol: Z-Wave™ (ZGM130S)
Frequency Range:
1pc ZA1502-7
1pc Operation manual
(ZA1502IN-7)
(ZA1502EU-7)
(ZA1502RU-7)
(ZA1502US-7)
(ZA1502IL-7)
(ZA1502KR-7)
(ZA1502HK-7)
(ZA1502JP-7)
(ZA1502BR-7)
22
42
00
42
00
923
80
926
42
865
868
869
908
916
919
919
922
921
.
.
.
.
.
~
.
~
.
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
Operating Range: Up to 100 feet line of sight
Operating Temp.: -10°C~ 60°C (14°F ~140°F)
System (0x09) Heartbeat (0x05)
Timer Ended (0x02)
Contact Medical Service (0x03)
Clock (0x0B)
Emergency (0x0A)
Movement
Synchronic Time
Button Press
Notification V8
Type:
TYPE EVENT
(Table 1)
0x09 0xFF
0x00
0xFF
0x09
0x0A
Movement
Synchronic Time
Button Press
V1 Alarm:
TYPE VALUE
(Table 2)
Configuration
Command Class:
BYTE VALUE Default
(Table 3) Parameter 1 1 ~ 127 (Set up from 16
to 2032 seconds) 4 (= 16 seconds x 4)1
Remark:
1. This is the definition how soon ZA1502-7 will contact Gateway after a movement behavior for triggering the
device and having a synchronic information. The basic interval time is 16 seconds, the synchronic time will be
the basic interval time by Parameter 1’s value.
2. The battery life will be shorter if the synchronic time is quicker.
Introduction
Thanks for choosing the Vision’s wireless 2 in 1 Universal
Remote (ZA1502-7) of the home security device. This sensor
is a Z-Wave Plus™. enabled device (interoperable, two-way
RF mesh networking technology) and is fully compatible with
any Z-Wav enabled network and its security framework. Every mains
powered Z-Wave PLUS™ enabled device acts as a signal repeater and
multiple devices result in more possible transmission routes which helps
eliminate “RF dead-spots”
Z-Wave Plus™. enabled devices displaying the Z-Wave Plus™. logo can also
be used with it regardless of the manufacturer, and ours can also be used in
other manufacturer’s Z-Wave Plus™. enabled networks. ZA1502-7 is an
Arrival sensor combines a unique button whose function can be defined as
one of below:
- Scene Control - Arm/Disarm
- On/Off Control - Emergency Help
When the device is secure included into Z-Wave network, above communica-
tion will be encrypted. ZA1502-7 supports SECURITY S0 / SECURITY S2
UNAUTHENTICATED / SECURITY S2 AUTHENTICATED.

3For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface
Controller into “inclusion” mode, and following its instruction to add the
ZA1502-7 to your controller. To get in the “inclusion” mode, quick press
the button of ZA1502-7 5 times for sending the NIF, the Red/Green LED
will flash 5 times quickly before the learning process for showing the
sensor has not been included. After sending NIF, Z-Wave will send the
auto inclusion, the Red/Green LED will flash 1 second after successful
inclusion; otherwise, ZA1502-7 will go to sleep after 30 seconds. The
red LED will be flashing while the inclusion is proceeding.
4For “Exclusion” from (removing from) a network: Put the Z-Wave™
Interface Controller into “exclusion” mode, and following its instruction to
delete the ZA1502-7 from your controller. Quick press the button of
ZA1502-7 5 times to be excluded, the Red/Green LED will flash 5 times
quickly after successful exclusion.
Note: All user and network settings will be cleared and the device reset
to factory defaults when the device is excluded.
5Trigger Response:
- Movement: The sensor will send Notification Report (refer to Table 1 &
2) if it has been moved.
- Synchronic Time: The sensor will send Notification Report (refer to
Table 1 & 2) and exceed the preset synchronic time (refer to Table 3).
- Button Press: Press the button of ZA1502-7 once for sending Notifica-
tion Report (refer to Table 1 & 2) if button has been pressed for any
specific purpose.
6Wake Up Notification:
Press the button of ZA1502-7 2 times will active the “Wake Up Mode” for
receiving all the command class from controller. The ZA1502-7 will go to
sleep mode without receiving any Z-Wave command till 10 seconds. It
will proceed all the commands after sending the “Wake Up Notification”
7Auto Wake Up:
Use “Wake Up” command to set up the awaking interval and send the
wake up notification to controller. User can use “Wake_Up” command
to change the auto wake up interval from 10 minutes to 1 week, Interval
increment is 200 seconds. (Default Value: 24 hours.)
8Battery Capacity Detection:
Use “Battery Get” command to have the battery capacity back in %. It
will detect the battery capacity automatically. Low Battery Auto Report
(low battery is set as 2.2+/-0.1 Voltage).
9Association:
* Support one group with 1 node.
* Group 1 = Lifeline (Battery, Notification, Reset Locally)
10 Support Explorer Frame Function
11 All the rest commands depend on Z-Wave standard
12 Factory Default Reset:
Quick press the button of ZA1502-7 4 times with another press and hold
the button around 5 seconds until the Red LED is on to send the “Device
Reset Locally Notification” command and reset to the factory default.
(Remark: This is to be used only in the case of primary controller being
inoperable or otherwise unavailable.)
13 Support OTA Firmware update from controller. Please refer to your
controller manual. Once OTA function success, we recommend you
exclusive the device & inclusive again before use the device.
14 Support SECURITY S0, SECURITY S2 UNAUTHENTICATED &
SECURITY S2 AUTHENTICATED.
15 Support SmartStart, please scan the QR Code from ZA1502-7 for
SmartStart. QR code and PIN is located on the device, also there is a
Full DSK string on the enclosed DSK card. Please keep DSK card
carefully for future inclusion needed.
(P.S.: Z-Wave SmartStart aims to shift the tasks related to inclusion of
an end device into a Z-Wave network away from the end device itself,
and towards the more user-friendly interface of the gateway.)
16 The DSK label will on the backside of ZA1502-7, Scan the DSK label to
access the SmartStart if gateway 's UI supports SmartStart. (Remark:
The QR code is for use with Z-Wave SmartStart by using “DSK,”
“Device Specific Key,” “PIN,” or “PIN code,” etc.)ateway.)
17 Enable/ Disable SmartStart:
Press the button of ZA1502-7 3 times continuously and hold the button
around 5 seconds until the Red LED and Green LED is flashing sequen-
tially. Enable and Disable is under a circle switching.
The default status is “Enable” after every time’s power on.
P.S.: The LED indicator for Enable / Disable SmartStart:
- Enable: One time’s LED flashing. (Red → Green)
- Disable: Two times’ LED flashing. (Red → Green → Red → Green).
18 A Security Enabled Z-Wave Controller must be used to fully utilize the
products.
1Green LED turns on while pressing the button of ZA1502-7.
2Quick press the button of ZA1502-7 5 times for showing the sensor’s
inclusion status.
- Not Included : Red/Green LED flashing 5 times quickly.
- Included : Red/Green LED flashing 1 second.
Notice: If you are installing the entire Z-Wave™ system for the
first time, please refer to the installation guide of Z-Wave™
Interface Controller and full charging the ZA1502-7 before using.
Operation
Button
ZA 1502-7