VISIONARY DESIGNS VK-1317 Manual

© 2017
www.classicexhibits.com
Order #XXXXX
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
VK-1317 - 10’x10’ Inline Display
Plan View
10’
10’

© 2017
www.classicexhibits.com
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2017
www.classicexhibits.com
Order #XXXXX
Crate 1 of 1
Crate Packing

© 2017
www.classicexhibits.com
Order #XXXXX
Step 1 of 5
Left Section Assembly
1
2
3
4
6
7
8
9
11
10
10
12
12
Infill
Infill
Infill
Infill
Door
Door
Counter
When
assembled
5
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
Item
1
2
3
4
5
6
7
8
9
10
11
12
Qty.
1
1
1
1
1
1
1
1
1
2
1
2
Description
96”h Vertical Extrusion
96”h Vertical Extrusion
38.2880”w Horizontal Extrusion
38.2880”w Horizontal Extrusion
38.2880”w Horizontal Extrusion
37.5”h 90° Vertical Extrusion w/ Door Hinges
37.5”h 90° Vertical Extrusion w/ Door Hinges
33.9170”h Vertical Extrusion w/ Door Stopper
41.36”w Horizontal Extrusion
16”w Horizontal Extrusion
41.36”w Horizontal Extrusion
16”w Horizontal Extrusion
Steps:
1) Attach lower horizontals [3,9,10] between verticals [1,2,6,7].
2) Attach vertical [8] atop lower horizontal [9] as shown.
3) Attach doors to verticals [6,7]. Refer to Door Attachment detail.
4) Place infills between verticals as shown.
5) Attach upper horizontals [4,11,12] between verticals [1,2,6,7].
6) Place large backwall infill between verticals [1,2].
7) Attach upper horizontal [5] between verticals [1,2].
8) Place counter atop assembled backwall counter.

© 2017
www.classicexhibits.com
Order #XXXXX
Step 2 of 5
Monitor Mount Attachment
13
13
When
assembled
Item
13
Qty.
1
Description
45”w x 6”h Horizontal Extrusion
for Monitor Mount Support
Steps:
1) Attach horizontal extrusion [13] to verticals.
2) Attach monitor mount to horizontal extrusion [13].
Monitor Mount Attachment
Attach mounting plate
to verticals as shown.
Then attach
wall plate to plate
using bolts and wing nuts
Slide mounting connector pieces
into groove of extrusion. Tighten
setscrew to secure in place.
Setscrew
Setscrew

© 2017
www.classicexhibits.com
Order #XXXXX
Step 3 of 5
Lightbox Assembly
15
16
Power Power
Wing
Wing
Florescent LightFlorescent Light
Florescent LightFlorescent Light
17
18
19
20
When
assembled
Item
15
16
17
18
19
20
Qty.
1
1
1
1
1
1
Description
94.75”h Vertical Extrusion
94.75”h Vertical Extrusion
39.8250”w Horizontal Extrusion
39.8250”w Horizontal Extrusion
39.8250”w Horizontal Extrusion
39.8250”w Horizontal Extrusion
Steps:
1) Attach horizontal extrusions between verticals.
2) Attach SGG fabric graphic to extrusions [15-20].
3) Attach wings to verticals as shown. Refer to detail.
Tighten set screw to
secure A10 to extrusion.
A10 Clamp Detail
Tighten knob to secure
header/wing in place.

© 2017
www.classicexhibits.com
Order #XXXXX
Step 4 of 5
Lightbox Assembly (cont’d)
15
Wing
Wing
Wing
17&18
When
assembled
21
*
**
21
22
23
14
14
Bolt When assembled
14
24
Item
14
21
22
23
24
Qty.
1
1
1
1
1
Description
Base Plate
95.750”h Formed Vertical Extrusion
95.750”h Formed Vertical Extrusion
39.825”w Horizontal Extrusion
39.825”w Horizontal Extrusion
Steps:
1) Assemble formed verticals, horizontals, base plates, and assembled
light box together using bolts as shown. Refer to detail below.

© 2017
www.classicexhibits.com
Order #XXXXX
Step 5 of 5
Kiosk Assembly
When
assembled
Counter
Sintra
Cap
1
2
3
4
5
6
6
6
6
Item
1
2
3
4
5
6
Qty.
1
1
1
1
1
4
Description
Base Plate
48”h Formed Vertical Extrusion
48”h Formed Vertical Extrusion
6”w Round Top
21.594”w Horizontal Extrusion
16”w Counter Support
Steps:
1) Assemble formed verticals, horizontal, round top, and base plate
together using bolts and locks as shown.
2) Attach counter supports [6] to horizontal [5].
3) Slide counter into assembled kiosk and place atop counter supports.
iPad
Bottom View
of Counter
Six Thumbscrews
iPad Insert