Visionary VK-1064 User manual

www.classicexhibits.com
Step 1
Page 1 of 2
866.652.2100
© 2008
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1064 - Magellan Miracle - General Layout
10’
10’
Plan View

www.classicexhibits.com
Step 2
Page 2 of 2
866.652.2100
© 2008
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C EliateDDliateDDetail B
Detail A
Setscrews

www.classicexhibits.com
Step 1
Page 1 of 2
866.652.2100
© 2008
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Backwall Assembly
1
2
3
4
5
6
7a
8a
9
10
11
12
Part Number
1
2
3
4
5
6
7a/7b
8a/8b
9
10
11
12
Qty
1
1
1
1
1
1
1/1
1/1
1
1
1
1
Description
48.5”h Lower Curved Extrusion
48.5”h Upper Curved Extrusion
48.5”h Lower Curved Extrusion
48.5”h Upper Curved Extrusion
48.5”h Lower Curved Extrusion
48.5”h Upper Curved Extrusion
44”w Horizontal Extrusion
44”w Horizontal Extrusion
23”w Horizontal Extrusion
23”w Horizontal Extrusion
Backwall Support Leg Extrusion
Backwall Support Leg Extrusion
Steps
1) Connect backwall upper and lower verticals together [ 1 to 2, 3 to 4 and 5 to 6].
2) Connect horizontal extrusions together [7a to 7b and 8a to 8b].
3) Attach horizontal assemblies [7a/7b and 8a/8b] between vertical
assemblies [1/2 and 3/4].
4) Attach horizontal extrusions [9 and 10] between vertical assemblies
[3/4 and 5/6].
5) Attach support leg extrusions [11 and 12] to back of verticals [1 and 5], see
leg attachment detail.
6) Attach monitor mount to upper vertical [4].
7b
8b
Backside of backwall
Graphic Attachment
Apply graphics to back
of assembled backwall.
4
Monitor Mount
Monitor Mount Attachment
Light Connection
Attach Lights to
Backwall where
desired and tighten
in place.
Connect support leg
to vertical by placing lock
into slot and tighten with tool.
Support Leg Attachment

www.classicexhibits.com
Step 2
Page 2 of 2
866.652.2100
© 2008
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Part Number
13
14
14a
15
16
Qty
1
1
1
1
1
Description
Base Plate
37.6”h Curved Vertical Extruaion
Oval Flange Plate
18.5”w Horizontal Extrusion
15.69”w Horizontal Extrusion
Steps
1) Attach curved vertical [14] to base plate [13],
see Base Plate Attachment detail.
2) Attach horizontal extrusions [15 and 16] between
curved vertical [14] and backwall vertical [3]
where indicated.
3) Attach flange plate to top of vertical [14] as shown.
4) Place counter top on assembled counter base,
see Counter Attachment detail.
Base Plate Attachment
13
14
15
16
Connect Vertical Extrusion to Base
Plate by placing lock into slot
and tighten with tool.
14a
Screw
Counter Top Attachment
Insert screws located on underside
of counter into holes on flange plate
and secure with wing nuts.
Backwall Workstation Assembly