VisionQuest LVQ2001 User manual

Model : LVQ2001
20'' LCD HDTV Owner's Manual

-1-
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS............................................................................................................
PREFACE...........................................................................................................................................................
WARNING AND CAUTIONS...............................................................................................................................
SPECIFICATIONS..............................................................................................................................................
ACCESSORIES..................................................................................................................................................
TV ASSEMBLY DRAWINGS...............................................................................................................................
INSTALLATION
FRONT .......................................................................................................................................................
BACK..........................................................................................................................................................
PC................................................................................................................................................................
ANTENNA....................................................................................................................................................
AV EQUIPMENT............................................................................................................................................
BATTERY INSTALLATION (REMOTE CONTROL UNIT) ...................................................................................
REMOTE CONTROL DESCRIPTION ....................................................................................... ........................
OPERATION INSTRUCTIONS
PC................................................................................................................................................................
VIDEO..........................................................................................................................................................
TROUBLESHOOTING GUIDE............................................................................................................................
SERVICE TIPS .................................................................................................................................................
Please read all the safety and operating instructions carefully before you begin.
Safety class
This is an IEC safety class I product and must be grounded for safety.
1-2
3
4-5
6
6
7
8
8
9
10
11
12
13-14
15-17
18-24
25
26

1.Read these safety instructions.
2.Keep these safety instructions.
3.Heed all warnings.
4.Follow all safety instructions.
5.Do not use this apparatus near water.
6.Clean only with dry cloth.
7.Do not block any ventilation openings. Install in accordance with manufacturer instructions.
8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including Amplifiers) that produce heat.
9.Protect the power cord from being walked on or pinched particularly at plugs convenience
receptacles, and the point where they exit from the apparatus.
10.Only use attachments/accessories specified by the manufacturer.
11.Unplug this apparatus during lightning storms or when unused for long periods of time.
12.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
13.Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such
as vases, shall be placed on the apparatus.
14.No naked flame sources, such as lighted candles should be placed on the product.
15.A warning that an apparatus with class I construction shall be connected to a MAINS socket
outlet with a protective earthing connection.
16.where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect
device shall remain readily operable.
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
-1-

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN!
CAUTION
CAUTION
The symbol indicates that dangerous voltage constituting a
risk of electric shock is present within this unit.
The symbol indicates that there are important operating and
maintenance instructions in the literature accompanying this
unit.
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
WARNING:
IMPORTANT SAFETY INSTRUCTIONS
-2-

INSTALLATION
CAUTION
Thank you for purchasing this TV. To enjoy your set from the very beginning, read this manual carefully and
keep it handy for ready reference.
Position the TV in the room where light does not strike the screen .
Total darkness or a reflection on the picture screen can cause eyestrain. Soft and indirect lighting is
recommended for comfortable viewing.
Allow enough space between the TV and the wall to permit ventilation.
Avoid excessive warm locations to prevent possible damage to the cabinet or premature component
failure.
This LCD TV can be connected to AC 100-240 Volts. 50/60 Hz. Never connect to a DC supply or any
other power supply.
Do not cover the ventilation openings when using the TV.
directly
Never tamper with any components inside the TV, or any other adjustment controls not mentioned in this
manual. All LCD-TVs are high voltage instruments. When you clean up dust or water drops on the LCD
PANEL or CABINET, the power cord should be pulled out from the receptacle, then wipe the TV with a dry
soft cloth. During thunder and lightning, unplug the power cord and antenna cord to prevent damage to your
TV. All repairs to this TV should only be performed by qualified TV service personnel.
PREFACE
-3-

Warning
High voltages are used in the operation of this television
receiver. Do not remove the cabinet back from your set.
Refer servicing to qualified service personnel.
Warning
To prevent fire or electrical shock hazard, do not expose the
television receiver to rain or moisture.
Warning
Do not drop or push objects into the television cabinet slots
or openings. Never spill any kind of liquid on the television
receiver.
Caution
Do not block the ventilation holes in the back cover. Adequate
ventilation is essential to prevent failure of electrical
components.
Caution
Do not squash power supply cord under the television
receiver.
WARNINGS AND CAUTIONS
-4-

Caution
Never stand on, lean on, or suddenly push the television or
its stand. You should pay special attention to children.
Serious injury may result if it should fall.
Caution
Do not place your television on an unstable cart, stand, shelf
or table. Serious injury to an individual, and damage to the
television, may result if it should fall.
Caution
When the television receiver is not used for an extended
period of time, it is advisable to disconnect the AC power
cord from the AC outlet.
Caution
Avoid exposing the television receiver to direct sunlight and
other sources of the heat. Do not stand the television receiver
directly on other produces which give off heat .E.g.video
cassette players and audio amplifiers.
Do not place naked flame sources, such as lighted candles on
the television.
Caution
If the television is to be built into a Compartment or similarly
enclosed, the minimum distances must be maintained. Heat
build-up can reduce the service life of your television, and
can also be dangerous.
Dim:515*320mm(
WARNINGS AND CAUTIONS
-5-

SPECIFICATIONS AND ACCESSORIES
ACCESSORIES:
One Remote Control Two size AAA batteries
A
B
C
D
Accessories for hanging
One AC cord
-6-
Model
LCD panel
Television system
AV system
Channel coverage
Analog RGB mode
Resolution
Display Colour
Comb Filter
Contrast
Brightness
Viewing angle
OSD language
Power source
Power consumption
Audio power
Lamp life
Video/Audio
terminals
LVQ2001
20 INCH TFT LCD
NTSC-M/N
PAL-M/N
PAL-4.43MHz-50Hz NTSC-3.58MHz-60Hz SECAM-4.29MHz-50Hz
NTSC-4.43MHz-60Hz PAL-3..58MHz-50Hz
PAL-3.58MHz-60Hz PAL-4.43MHz-60Hz
VHF-L:
VHF-H:
UHF:
640X480/60Hz, 800X600/60Hz
800X600
16.7million colours
Adaptive 2/4 line
800:1
2
500cd/m
170°(H)/170°(V)
English/French/Italian/Portuguese /Spanish
DC 12V/5A, 100-240V, 50/60Hz
60W
3W+3W
50,000 hours
RF input: Cable/ antenna RFx1
VIDEO input: VIDEOx1
S-VIDEOx1
YCb/Cr x 1
GRAPHIC input: Analog RGB 15pin x1
AUDIO input: 3(VIDEO YCbCr,PC)
When a signal is absent loner than 10 minutes the unit will
automatically switch off.
Remote control, AC adapter, AC cord, Instruction Manual, Batteries.
Accessories for hanging be attached as customer need
101 199 MHz
195 499MHz
501 933 MHz
Supplied accessories
Auto switch off
SPECIFICATIONS
One AC adapter

1. Adjust the angle of the screen.
2. Hang the TV on the concrete wall.
The horizontal angle could be adapted to suit yourself. It’s range is up to 40°.
Seeing drawings below.
Step1:Disassemble the pedestal.
Step2:Hang the TV on the wall refer to
drawings below.
Distance between hole A and B is 40mm;
Distance between hole A and C is 175mm;
Angle can be adjust between +/-27°
vertically.
3. Assemble stand
TV ASSEMBLY DRAWINGS
Seeing drawings right side.
-7-
X2
X2
X4
X4
¹Òǣϵͳ
A
B
C
D
X6
X4
40°

1.MENU: To enter main menu or enter the item where the cursor is.
2.CH+/CH-:Move the cursor in the main menu or change program in TV mode.
3.VOL+/VOL-: Adjust the item you select or adjust volume.
4.AUTO/EXIT: Act as AUTO adjustment hot key when OSD is not displayed. Otherwise perform
erase OSD.
5. : Video source select or power off. Press this key longer than 3 seconds to turn off the
TV.
FRONT
INSTALLATION
Buttons:
-8-
IRIR
CH+
CH-
VOL+
VOL-
MENU
AUTO/EXIT
BACK
+
-
+
-
ANTENNA INPUT

STEPS:
INSTALLATION
*Please don't open the Cover
1. Connect Video Cable
a. Make sure both the TV and computer are powered-OFF.
b. Connect the video cable to the computer.
2. Connect the Audio cable.
3. Connect power cord
Connect the AC ADAPTOR to the TV, then to a properly grounded AC outlet.
4. Power-ON Computer
Power-ON the TV first, then Power-ON the computer.
This sequence is very important.
5. If the TV still does not function properly, please refer to the troubleshooting section to
diagnose the problem.
CAUTION:
Hold on to the connector lug when you unplug any one of the connectors, Do not direct pull on
the cord as it is prone to damage.
PC:
-9-
8
Connector lug
+
-
+
-

ANTENNA
INSTALLATION
-10-

You can also the S-VIDEO terminal if your video equipment has S-VIDEO.
It can be connected to the following appliances: VCR, multi disc player, DVD, camcorder,
video game or stereo system, etc.....
If your DVD player can output interlace and progressive mode signals, select the interlace
output when connecting to component video input on your TV. Your TV can receive either
525i/60Hz or 625i/50Hz interlace signals.
This TV provides one group of AV input terminals including one S-Video and one group of YCbCr
for convenient connection to VCR, DVD or other video equipment. Please refer to the owner’s
manual of the equipment to be connected as well. You can use the AV and YCbCr input terminals
on TV set rear as follows.
AV EQUIPMENT
*Please keep AC cord unplugged when connecting TV system.
-11-
To audio
outputswith
terminal
VIDEO EQUIPMENT
VIDEO EQUIPMENT with YCbCr
To audio outputs
VIDEO EQUIPMENT
To S-VIDEO
output
Yellow (video)
White(audol L,mono input)
Red(audio R,Cr)
Y
W
R
Y W R
RWY
W R
W R
output
To video
GBR
GBR
R
W
G
B
Green(Y)
Blue(Cb)
INSTALLATION
R
W
+
-
+
-
with S-video terminal

1. Remove the battery cover.
2. Insert the two AAA 1.5V batteries and ensure correct polarity (+ or -)
3. Replace the battery cover.
Replace with new batteries when the TV set shows no response to the remote control.
Note:
BATTERY INSTALLATION (REMOTE CONTROL)
1. Alkaline battery recommended
2. Remove batteries when they are flat or if the remote control has not been used for a long time.
3. Do not mix new and old batteries or different types/brands.
Insert Batteries Into the Remote Control
-12-

REMOTE CONTROL DESCRIPTION
-13-
17
9
5
8
7
612
10
4
3
13
2
111
15
16
18
POWERPOWER MUTEMUTE
SYSTEMSYSTEM RETURNRETURN
MTSMTS
VOLVOL CHCH
SLEEPSLEEP
MENUMENU
AUTOAUTO
VCRVCR
SOUNDSOUND PICTUREPICTURE
DISPLAYDISPLAY
INPUTINPUT
1.POWER:turn on or off the TV
2.NUMBER BUTTONS
3.VOL+/- :adjust volume
4.CH+/- :change program forward/backward
5.MENU: access main menu
6.BUTTONS / : move cursor in main menu
7.BUTTONS / : adjust item you selected
8.DISPLAY: recall program number, system etc on the screen
9.RETURN: return to the last viewed program
10.INPUT: select external video source
11. MUTE: mute sound
13.SLEEP: set time to turn off the TV
12.MTS :MONO/STEREO AND SAP
14

REMOTE CONTROL DESCRIPTION
DIRECT PROGRAM SELECTION (0-9 BUTTONS)
1.To select one-digit channel:
Press 0-9 digit buttons and wait for 2 seconds. For example if you need channel 5, please
input "5" button and the screen displays "5", the TV set goes to channel 5 in 3 seconds.
2.To select two-digit channel:
Press two digit buttons in order to input the channel number. For example, you need channel
10, please input "1" button, followed "0" button and the set goes to channel 10. Be sure that the
second press should be within 2 seconds.
3.To select three-digit channel:
Press three digit buttons in order to input the channel number. For example if you need
channel 110, please input "1" button firstly, followed "1" button secondly and followed 0 button
thirdly then the set goes to channel 110. Be sure that the second press is within 2 seconds.
-14-
14.SYSTEM:shift frequency system(STD,HRC,IRC,AIR)
15.
16.
17.SOUND:3 sound mode.SPEECH STANDARD MUSIC
18.PICTURE:3 picture mode.SOFT STANDARD RICH
VCR:rectify distorted signal from VCR (video cassette recorder ).
AUTO: auto adust the position and size of the picture in PC mode

All MENUs are shown below
OPERATION INSTRUCTIONS PART I (PC)
-15-

AUTO CONFIG:
OPERATION INSTRUCTIONS PART I (PC)
:
-16-

OPERATION OF MAIN MENU
PRESET MODES
To reduce the need for adjustment of different modes, the TV has default setting modes that are
most commonly used, These are shown in the table below. For optimum adjustment, perform
the Auto Setup in Windows "Full Screen" mode.
There are 12 items listed in the main menu
Step1:Press menu to enter the main menu
Step2:press to select an item
Step3:press menu to enter this item
Step4:press to adjust this item
Item
Contrast
Brightness
H.Position
V.Position
Clock
Focus
OSD H.Pos.
OSD V.Pos.
Color
Language
Reset
Exit
Function description
Increase or decrease contrast
Increase or decrease brightness
Move image toward left or right
Move image toward up or down
Increase or decrease the size of image
Increase or decrease noise of the image
Move OSD position horizontally on the screen
Press move right,press move left
Move OSD position vertically on the screen
Press move up,press move down
Color temperature:6500K,9300K,USER
5 languages:
Perform auto adjust
Automatically adjust
H.Position,V.Position,Clock,Focus,White balance
Exit OSD
English/French/Italian/PortugueseSpanish
PRESET MODE (recommended resolution is 800*600@60Hz)
1
2
3
4
5
6
7
8
9
720*400
640*350
640*480
640*480
640*480
800*600
800*600
800*600
800*600
70
70
60
72
75
56
60
75
72
31.47
31.469
31.47
37.86
37.50
35.156
37.88
46.88
48.08
28.322
25.175
25.175
31.5
31.5
36
40
49.5
50
-/+
+/-
-/-
-/-
-/-
+/+
+/+
+/+
+/+
RESOLUTION V.Freq.(Hz) H.Freq.(KHz) Band
Width(MHz)
Polarity
H/V
OPERATION INSTRUCTIONS PART I (PC)
-17-

OPERATION INSTRUCTIONS PART II(VIDEO)
TUNING PROCEDURE(NOTE)
STEP 2: AUTO MEMORY
STEP 1: Turn on the TV
-18-
1
1. Press the MENU button on your TV (or remote controller) three times to enter TUNING menu.
If it is in VIDEO/S-VEDIO/YCbCr /PC mode, it can't enter TUNING menu.
2. Press Buttons to select "AUTO MEM." then press button to automatically search
and store all the signals in your area. broadcasting TV When presetting complete, the initial
position number will reappear.
NOTE:
You 'd better select the correct frequency system, color and sound system for the first channe
before searching. Detailed discreption is said below.
There are 4 frequency system can be used, such as STD,HRC,IRC,AIR.
In AIR mode, the set receives antenna signals;
In STD/HRC/IRC mode the set receives Cable TV programs.Please select:
AIR: If using VHF/UHF antenna.
STD,HRC,IRC:If using Cable TV.
TO SKIP A PROGRAM
You may skip any program number by following the steps below:
1.Select the program number to be skipped by pressing CH+/CH- button or number button .
2.According to mentioned steps above, enter TUNING menu.
3.Press buttons to select "ADD/ERASE", then select "ERASE" by buttons.
4.When the skip is off, it indicates that this channel is not skipped.
NOTE:
If the channel is skipped,you can't obtain it by CH+/CH-. But you can get it by using
NUMBER KEY(0-9).