VisionTek CANDYBOARD RF06 User manual

1
USERS MANUAL
Model RF06

2 3
Safety Precautions
Safety Matters
Please refer to all safety precautions covered in this user
manual to prevent injury or damage.
This product contains a rechargeable lithium-ion battery. All
safety precautions should be taken into consideration when
handling and or operating any type of device that is pow-
ered by a battery such as this product. Do not drop, heat,
crush or submerge this product in water. Do not operate this
device in extreme humidity, heat or cold environments for
long periods of time. Misuse of this device may cause injury
and will void the device’s warranty.
Attention to trafc safety
Do not operate or attempt to operate this device
while driving or operating any moving vehicle.
Aircraft Safety
Please do not operate or attempt to operate this
device while on board an aircraft. Doing so may
cause interference with the aircrafts operations
and communications devices.
Combustible Agents and Chemicals
Please turn the device off while around fuel or
any combustible agents or chemicals.
Turn off this device in the hospital
Please do not operate or attempt to operate
this device in a hospital. Doing so may cause
interference with medical operations and
communications devices. As with all wireless
devices, this product may interfere with
implanted cardiac pacemakers, hearing aids
and other medical implant devices.
Interference
All wireless devices may be subject to
interference, thus affecting the performance
of this product.
Replacement parts
Do not use any replacement parts other
than those provided or recommended by the
manufacturer.
Do not look directly at or point the laser at
eyes. Doing so may cause permanent dam-
age or blindness.

4 5
OVERVIEW
This device is a combo 2.4GHz Wireless mini QWERTY
mini keyboard and Touch Pad combo with USB interface
receiver. In addition to standard keyboard functionality,
this device offers multimedia control keys and PC gaming
control keys. It has a built-in programmable smart touch
pad. This touchpad can be used in horizontal and vertical
directions. It also has power indicator, RF signal indicator,
CAPSLOCK light, low-voltage indicator and keypad back-
light to facilitate the use in dark environments.
In addition, this mini keyboard is also a universal infrared
remote controller with learning function. The remote control
is very effective at identifying unknown format with a wide
and reliable range of learning formats which means about
99.9% TV infrared remote control on the market can be
learned .After learning, the signals can be transmitted with
a high precision wide learning range of 20kHz~60kHz and
a small frequency error of (±1kHz).
Touchpad
The touchpad can be used in a horizontal or vertical posi-
tion. To switch between horizontal or vertical mode, hold
the Fn key and hit the Alt key.
Wireless 2.4G receiver
Connecting the receiver
Take out the 2.4G dongle from the giftbox, and insert
to the device into a standard USB interface. Once con-
nected, slide the power switch to the “ON”
position located on the left side of the unit to establish
the connection.
Enabling the backlight
Once the keyboard has established a connection to the
receiver, the backlight keys will automatically turn on for
3 seconds. The backlight will turn off after 3 seconds to
preserve battery life. To manually turn the backlight on,
simply press the key with light bulb symbol on upper left
hand corner.
Auto sleep and wake feature
The keyboard also features an auto sleep and auto
wake mode. If there is a long period of inactivity, the
keyboard will automatically go into a sleep mode. Dur-
ing the sleep mode, the user can wake the unit up by
pressing any key. The 2.4 GHz receiver and keyboard’s
RF indicator will continue to ash and will not power
down

6 7
Charging the battery
This device utilizes a built- in lithium-ion battery, please use
only approved data lines and chargers. Note: Fully charge
the unit before operating for the rst time. This device can
be used when charging, but will extend the charging time.
When the battery is low, the low-voltage light will ash
to warn the user. The unit will automatically turn off if the
battery has been depleted.
Note: Fully charge the unit before operating for the rst
time. This device can be used when charging, but will
extend the charging time.
How to operate
1 Press the Set1/Set2 of “remote” for 3 seconds, the
remote’s light will ash once time then stay on for long-time
2 Aim the remote’s infrared LED at your original remote
control’s infrared LED in parallel alignment (PS: the relative
distance not more than 7 cm), then press any button on
remote, the remote’s light will ash two times then long¬time
on, it is in learning status.
3 Press any button on original remote control, remotes light
will ash three times then another long light when success-
fully learned.
4 Repeat the step 2-4, until nish learning all keys.
5 Press the set key or 10 seconds without any operation, the
device will retire from the learning state.

8 9
Basic functions
RF matching
The device has been pre-coded at the factory to match a
keyboard to the receiver. This ensures that two or more
of the same device will not interfere with each other on
the same wireless spectrum. In the event this device is
in conict with another wireless device, you can change
channels to avoid interference by pressing the two keys
FN and F1 about 10 seconds. The RF indicators will ash
from slow to rapid. Once the channel has changed, the RF
indicator will fall back to a slow ash conrming that the
change was successful.
Appendix
Technical parameters
Specication
• Measurements (L x W x H): 151.1mm x 59mm x 3.8mm
• Weight (grams): 100g / 0.22 lbs
• Operational Range: up to 10 meters/ 30 feet
• Output power (db): +4db Max.
• Operation voltage: 3.3V
• Operation current: < 150mA
• Charging current: < 350mA
• Hibernation current: < 1mA
Supported Environment
• Windows 2000,Windows XP, Windows Vista ,Windows
CE, Windows 7
• Linux(Debian-3.1,Redhat-9.0 Ubuntu-8.10 Fedora-7.0
tested)
• Microsoft Xbox 360 (*may require rmware update)
• Sony PS3* (*may require rmware update)
Maintenance
• Do not attempt to disassemble the device or replace
rechargeable battery. Doing so will void the warranty.
• The battery will discharge if stored for a long period of
time without usage.
• Use the specied charger. Disconnect the device after
the battery has been fully charged. Overcharging the
battery will shorten the life span of the battery.
• Do not expose the device in extreme heat or cold.
Extreme temperatures will cause the life span of the
battery to shorten.
• Use only a damp cloth with mild soap to clean the
device. Solvents and other cleaning agents may cause
damage to the device.
Troubleshooting
Below are some basic troubleshooting options for the
device. Please contact VisionTek Technical Support at sup-
port.visiontek.com if you are unable to resolve any issues
with the device.

10 11
Unit does not
respond
Keyboard can-
not establish a
connection to
the receiver.
The mouse
pointer moves
erratically and/
or unrespon-
sive.
The unit does
not charge.
1. Low battery
power.
2. Unit is not turned
on.
1. The receiver
may not be inserted
correctly.
2. Possible wireless
interference with
another device.
1. Device may not
be within optimal
range of the re-
ceiver
2. Dust or oil on the
touchpad.
1. Check connec-
tions.
2. Defective battery.
1. Charge the
device for at least
15 minutes.
2. Check if the
switch selected to
the “ON” position.
1. Disconnect and
reconnect the
receiver to the USB
port.
2. Change the
channel of the
device by pressing
and holding the
Fn+ F1 key for 10
seconds and let the
unit reconnect.
1. Bring the unit
closer to the
receiver.
2. Clean the touch-
pad with a damp
cloth.
1. Verify if the
device is securely
connected to the
charger.
2. Contact Vision-
tek for support.
Problem Possible Issue Solution
Packing list
This equipment package contains the following items:
Candyboard Wireless Keyboard 1 unit
Wireless receiver 1 unit
USB-A to Mini-B Charge only Cable 1 unit
User Manual 1 unit
One Year Warranty
Products Covered:
Candyboard Wireless Keyboard Model RF06
VisionTek Products LLC, (“VisionTek”) is pleased to
warrant to the original purchaser (“Warrantee”) that
the product will be free from manufacturing defects in
material for One (1) Year when given normal and proper
usage. You must register product at www.visiontek.com
to be eligible for 1 year warranty program.
The provisions of this warranty shall not apply if, in
VisionTek’s sole judgment, the product has been
subjected to incidental damage including but not limited
to the following:
- Removal of Serial/Part number sticker(s)
- Damaged while being installed
- Damaged by software or hardware by someone
other than VisionTek or by motherboard, laptop, USB
port, Wi, Blue tooth, or improper use.
- Damaged by tampering, user error, disaster, mis-
use, neglect, abuse, power supply, power application,

12 13
alteration, repair, modication, a x or replacement by
an unauthorized technician that in any way affects its
performance or reliability.
VisionTek’s liability under this warranty, or in connection
with any other claim relating to the Product, is limited to
the repair or replacement, at VisionTek’s option, of the
product or portion of the product which is defective in
manufacturing material. Warrantee assumes all risk of loss
in transit. The returned products shall be the sole property
of VisionTek. VisionTek warrants the repaired or replaced
Products will be free from manufacturing defects in mate-
rial for the remainder of the warranty period.
VisionTek reserves the right to impose a reasonable
charge for the repair of products returned with defects
resulting from any of the above causes and for returns
where the product is found to be in good working condi-
tion.
VisionTek reserves the right to replace any defective
VisionTek product with an equivalent or superior product
at VisionTek’s sole discretion. Such replacement product
may be a remanufactured product or manufactured using
remanufactured components at VisionTek’s option. The
repaired or replaced product will be covered by the same
warranty as the original product.
To receive warranty service, contact VisionTek’s Technical
Support department. Before returning any product for
service, you must have rst communicated with one of our
service representatives. The service representative will
issue a Return Material Authorization (RMA) request and
additional instructions for receiving the RMA number. No
VisionTek product will be accepted for warranty service
without a copy of a valid proof of purchase and an RMA
number. Your sales receipt or invoice from a retail store
is your proof of purchase. The warrantee shall pay
the cost of returning the defective product to and from
VisionTek’s service center.
No other warranties are expressed or implied, including
but not limited to, any implied warranties of merchant-
ability or tness for a particular purpose. In no event shall
VisionTek be liable for any consequential or incidental
damages resulting from the use or installation of any Vi-
sionTek product, or the breach of any express or implied
warranties. VisionTek’s liability to any warrantee with
respect to any claim or loss arising out of this transaction
or alleged to have resulted from an act or omission of
VisionTek shall be limited to warrantee’s cost of the
VisionTek product.
Some states do not allow the exclusion of consequential
or incidental damages, so the above exclusion may not
apply to you. This warranty provides you with specic
legal rights. You may have other rights, which vary, from
state to state.
VisionTek reserves the right to inspect and verify the
defectiveness of any products or portion of product

14
If you have any questions
about this product call
TOLL FREE Tech Support
866-VTEK411
returned. This warranty does not apply to any software
component.
EXCEPT AS EXPRESSLY STATED ABOVE, VISIONTEK
MAKES NO WARRANTY, EXPRESS OR IMPLIED,
WHETHER OF MERCHANTABILITY, NON-INFRINGE-
MENT OF INTELLECTUAL PROPERTY, FITNESS
FOR ANY PARTICULAR PURPOSE OR USE, OR
OTHERWISE ON THE PRODUCTS, OR ANY PARTS
OR TECHNICAL ASSISTANCE OR OTHER LABOR
FURNISHED.
VisionTek reserves the right to change the terms of this
warranty without notice.