visplay Invisible6P/L User manual

play it smart
Invisible6P/L
Assembly and operating instructions

2
General Instructions
1/2019 (EN)
EN Visplay products are manufactured according to the
latest technology and comply with valid rules and
regulations.
Nevertheless, these products can cause injury or
damage if:
• the product is improperly installed
• the product is improperly used
• the product is improperly altered or modified
• original accessories are not used
• the safety regulations are not observed.
⚠WARNING
Each person involved in the planning,
installation and/or use of our products must be
carefully read and observe these instructions of
use.
The following are of course also valid:
• Relevant accident prevention regulations
• Generally recognized safety rules
• National regulations – please consult Visplay if there
is a discrepancy with the Assembly manual
Safety instructions
⚠WARNING
When playing, children often incorrectly assess
danger. You must therefore make sure that your
store fittings are not used as toys.
Please pay attention to the following points:
• Structural conditions, in particular the design and
bearing capacity of walls, ceilings and floors. If
bearing capacity for the specified tractive or pressure
load cannot be achieved by suitable fastening or
stabilising elements, please refrain from installation.
• All the structural components supplied for stabilising
structures are to be used in an unrestricted manner
and must not be removed.
• The products may only be loaded after all the
installation steps have been completed.
• Merchandise supports should be loaded as evenly as
possible.
• Avoid loading in fits and starts.
• The maximum weight loads is to be observed. This can
be found in the instructions on assembly and use, as
well as in our sales documentation.
• Furniture with castors is generally much more unstable
than furniture with glides. Tall, heavy structures on
castors should thus be avoided.
• The recommendations of your safety ocer should
also be observed.
General care for chrome, silk and pearl
In clothing retail applications, frequent dragging of
clothes hangers along the surface can cause slight
abrasion to their hooks. This eect is most pronounced
- more so than with front-on horizontal or inclined-pole
displays - where garments are hung side-on such that
hangers have to be moved more frequently. To prevent
garments from becoming soiled, cleaning of the hanging
rods is essential.
This abrasion can be considerably reduced by using a
coat hanger cover (scliss, 929-449.02).
No responsiblity can be accepted for damage caused by
soiling, as the above mentioned abrasion depends on the
material of the coathangers in use.
With powder-coated surfaces subject to frequent use,
use of special paints is recommended. We will be happy
to advise you.
Use and care of merchandise supports with
anodised aluminium surfaces
Visplay merchandise supports with anodised aluminium
surfaces are hard-wearing. However, the exchange of
accessories might cause slight marks on the surface.
Accessories with plastic inserts usually cause less wear or
none at all.
To remove the marks, we recommend using cleaning
agents ranging from pH 5–8 (do not use any detergents
with acidic or alkaline reaction). Clean by washing the
surfaces using a sponge and water containing a wetting
agent. Then remove any loose or greasy dirt. Rubbing
o the surfaces with detergent using pure cotton waste
or porous cleaning tissue and applying the necessary
pressure in rubbing direction will remove the marks.
Aluminium profiles with widths exceeding  mm must
be subjected to abrasive cleaning using detergents
specifically developed for this purpose. The cleaning
agents developed for abrasive cleaning contain very
finely ground neutral polishing agents and have to
be adapted to the oxide layer. Alternatively, cleaning
can be carried out using an abrasive fibrous web (e.g.
Scotch-Brite, type A, red, fine or very fine) in combination
with a non-abrasive detergent.
Subsequently, residual cleaning agents should to be
rinsed o using a sponge and clear water. Then rub o
the part with a chamois.

3
Invisible6P/L
318-532.05/.06
31
8-533.05/.06
31
8-534.05/.06
225-945.19
225-946.19
138-978.19 (75 W) 138-979.19 (EU)
138-980.19 (UK)
NV (24 V)
L = 500 mm
100–240 V
L = 200 mm
ø 7.7 mm
220–240 V
L = 1800 mm
1/2019 (EN)
EN
Technical Data Sheet Invisible 6 P/L
Invisible 6 P/L electrification in detail: conductor rail with power supply, integrated into system support profile.
Correct functioning and safety are guaranteed when properly used. No liability is accepted in event of improper use. Product safety
is based exclusively on the use of original Invisible 6P/L accessories from Visplay.
No alterations may be made, for safety reasons; the only exception being the shortening of profiles from the right-hand side.
The safety instructions of the assembly instructions must be followed as well as the instructions on the labels of the individual parts.
The indicated nominal current (A) may not be exceeded. The number of shelves with lighting that are connected to the conductor
rails also may not exceed the capacities indicated in the table.
In event of improper use or cleaning with liquids, a risk of electric shock exists due to possibly exposed live parts. Always disconnect
from power before cleaning or servicing.
If rails or adapters exhibit visible signs of damage, disconnect them immediately and inform your service technician.
Product safety
Converter 24 V for electrified profile
Converter 75 W with input voltage 100–240 V / mains frequency:
50–60Hz / electronic protection against overheating and short-
circuit.
- Mains connection with connector for mains cable
- Nominal voltage = 24V / SELV
- Safety class 2
Single power adapter 24 V
Single power adapters can only be used with the Invisible6P/L
system. Low voltage lighting may only be connected by trained
personnel.
If multiple adapters and appliances are used, their total power
consumption may not exceed the specified nominal current or
fuse rating. The permissible nominal voltage and nominal current
are also limited according to the adapters used (see printed label
and safety information).
Permissible nominal current max. 4A.
Invisible6P/L rail capacity
Profile length L=mm L=mm L=4455mm
Max. number of shelves with
lighting (6/10/13 W)
size 620x420mm 4 shelves 5 shelves 7 shelves
Only use Invisible 6P/L system accessories! Do not use any other parts.
The user is responsible for ensuring that any connected equipment is electrically, mechanically and thermally compatible with the conductor rail.

4
Invisible6P/L
1 2 3 4
UK
EU
5
1
54
5
4
3
1 22
1/2019 (EN)
EN
Check the power consumption of electrical appliances! Their maximum power consumption should be 10% below the nominal power of the
transformer.
Visplay connection system
Powering with 75 W transformer
Powering with 150 W transformer
1 Power supply 24 V left
2 Power supply 24 V right, incl. isolation
3 Visplay 24 V distributor, 8 way
4 Visplay LED transformer
5 Visplay mains cable 220–240 V

5
Invisible6P/L
34.5
30
72
10.4
312.5 ± 0.5312.5 ± 0.5 312.5 ± 0.5
72
28
Profillänge 2556 / 3181 / 4431 / lto± 1 max. 4431
Gesamtlänge (mit Einspeisung und Endkappe) 2580 / 3205 / 4455 / lto
± 1
max. 4455
Gesamtlänge 2580 / 3205 / 4455 / lto± 1 max. 4455
22 28 2
72
ø 7.514 =
optional
===
312.5 ± 0.5312.5 ± 0.5 312.5 ± 0.550 30
ø 7.5 =
optional
===
L = 50018030
60
L = 200
1/2019 (EN)
EN
The fastening material and the wall must be capable of supporting a min. tensile force of 180 kg per fastening point.
Please observe the indications concerning weight loading and ensure that the substructure of the wall units/furniture and their fixtures can
support the expected loads.
With free-standing furniture, ensure that there is sucient stability even with the intended merchandise supports.
Important information on electrified Invisible 6 P/L can be found in "Technical data sheet Invisible 6 P/L“.
Assembly dimensions / layout
End caps must be fitted on profile with conductor rail.
Dimensions - profile with electrical power
All fastening points are to be used in event of maximum loads!
Dimensions - profile without electrical power
All fastening points are to be used in event of maximum loads!
Total length (with infeed and end cap)
Total length
Length of profile

6
Invisible6P/L
5
ca. 60 x 30 x 2.
57
4
1618
4.5 4.5
21.5 30.5
10.410.1 10.1
6
3036
R 5.2
R 15.25
14
1422
1614.5
47.5
30.5
60
23.7523.75
11
22
5.
25
.2
A
A
A
A
A
min. 70
min. 25
min. 50
1/2019 (EN)
EN
Mounting to a panel from the rear
Mounting to a substructure
Length of profile
aprox.  x  x 
Length of profile + power supply +

orderered separately
Fastening examples
Depending on the type of wall the profil can be attached with dierent
fixation material.
The max. weight load of the profile depends on the nature of the wall,
on the number of fixation points as well as on the fixation material
used.
With wooden substructures, a screw length of min.  mm must be
observed.
Wood
Please observe the information on the loading values and ensu-
re that the substructure of the wall installation and its fastenings
can cope with the expected loads.
>The correct size and type of anchor fixings must be used to suit
the construction conditions.
>Check anchor fixing as specified by manufacturer.
>All mounting points must be used.

7
Invisible6P/L
20 16
28 312.5 312.5 28
312.5
312.5
2°
ok!
ok!
L - 24
Lx
Gesamtlänge 2580 / 3205 / 4455
22 2
1/2019 (EN)
EN
Profile assembly
Maximum loads
Optimal distance between the uprights:  mm
Fastening points
The system‘s functionality can only be guaranteed if the profile
lies completely flat against the aligned mounting surface! —> Use
pan-head screws!
Merchandise support slightly inclined upward (2°).
Increased carrying
capacity (up to 20%) can
be achieved by securing
the Invisible profile to
the panels by applying a
suitable adhesive.
Mount the power supply unit on
the left-hand side of the wall.It is
strongly recommended that mea-
sures be taken to allow access
for subsequent servicing. Leave
a gap between the converter
housing and panel.
The electrical components and end cap must be removed before
a profile is shortened. Always shorten a profile from the right-
hand side and trim the edges. Make sure that all shavings are
removed from the profile.
The electrical components and end cap must then be fitted back
onto the profile.
Shortening a profile Total length

8
Invisible6P/L
1 2 3
100
34
65
10010025
(75)
ø 5.3
8.5
3100 mm
lto = min. 250 max. 3100 mm
min. 50
1/2019 (EN)
EN
• Assembly
• Dimensions of holes
All fixation points are to be used with maximum loads.
• Fastening examples
Depending on the type of wall the profil can be attached with dierent
fixation material.
The max. weight load of the Invisible P/L profile depends on the
nature of the wall, on the number of fixation points as well as on the
fixation material used.
With wooden substructures, a screw length of min.  mm must be
observed.
For mounting on plaster, the following dowels are recommended
(manufacturer Hilti):
• Hollow toggle plug HTB-S Mx
• Hollow plug HHD-S M/x
 Screw the end caps to the profile with the
screws provided.
Drill holes into the wall at mm
intervals (note: to select the right fixtures,
see below "Front assembly on dierent
surfaces").
Screw the profile to the wall.
Fit the profile cover.
WoodPlasterboard
Invisible6P/L profile for attachment from the front, for walls
Instructions for use
Insert the not electrified Invisible support
or shelf into the profile at a slight angle
until the limit stop is reached.
Then lower the support or shelf.
Check that the Invisible merchandise
support or shelf has correctly clicked into
place.
Please observe the information on the loading values and ensu-
re that the substructure of the wall installation and its fastenings
can cope with the expected loads.
>The correct size and type of anchor fixings must be used to suit
the construction conditions.
>Check anchor fixing as specified by manufacturer.
>All mounting points must be used.

9
Invisible6P/L
316
19
16
3
19 18 16
3460 R5
17
3060
90
1915 44
15
16.5
50
17
R5
ø 2 x 8
65
1/2019 (EN)
EN
Spacer 929-192.06
The Invisible holder is screwed on from the
back with 6 screws.
Ensure that the rabbet size and a material
thickness of 19 mm are respected as
otherwise the cover cap set cannot be
correctly fitted
• Assembly
Spacers are only needed when hol-
ders are fixed in combination with the
profile into a 16 mm wooden panel.
Reduced load-carrying capacity with
16mm clamping plate!
• Examples of fixation
Spacer 929-192.06
Invisible 6 holder
• Assembly dimensions
The arrangement of the holders must be
adapted to the respective assortment and
expected load.
Wood 19mm

10
Invisible6P/L
2795
200
200 200
800
200 200
400
550
650
900
2650
2300
2550
2200
1950
2100
1700
1850
1600
1350
1250
1150
539.6
550
24.5
15–60
75.2
5.2
32
2450
200
325
450
575
700
2325
1950
2700
2575
2200
2075
1825
1575
1700
1325
1450
1200
1075
950
825
1/2019 (EN)
EN Change by Invisible6P/L
It is possible to shorten the profile by a grid
pitch of 200mm - max.800mm.
• Dimensions of the substructure for Fashion • Dimensions of the substructure for Health & Beauty

11
Invisible6P/L
Click!
Click!
Click!
312.5
312.5 312.5
1 2
44
(83)
3
77
1
1/2019 (EN)
EN
• Attaching the panels
Production drawings of the panel
is available for downloading on
www.visplay.com or can be received
on request.
Drawing no. 365-302
• Alignment and installation the substructure

12
Invisible6P/L
312.5 312.5
1 2
44
(83)
3
77
1
225-946.19
3000 Kelvin
332-420.05 580 mm (6W)
332-421.05 890 mm (10W)
332-422.05 1140 mm (13W)
4000 Kelvin
332-436.05 580 mm (6W)
332-437.05 890 mm (10W)
332-438.05 1140 mm (13W)
321-729.31
580
890
1140
(3.5)
34
12
Countersunk screw
M5 x 20 Countersunk screw
M5 x 20
1/2019 (EN)
EN • Side cover set
Wooden shelf for LED lighting fixture
Production drawings are available
for downloading on www.visplay.com
or can be received on request.
Drawing no.
229-881 620 mm
229-882 995 mm
229-883 1245 mm
Assembly option  Assembly option 
Distance to back panel

13
Invisible6P/L
318-532.05 580 mm (6 W)
318-533.05 950 mm (10 W)
318-534.05 1200 mm (13 W)
580
950
1200
321-729.31
987-348.31
987-881.01/.30/.07
(3.5)
34
1/2019 (EN)
EN
Production drawings are available
for downloading on www.visplay.com
or can be received on request.
Drawing no. 367-806
Glass shelf for LED lighting set
1. Glue the luminaire to the glass with the transparent double-sided
adhesive tape.
2. Feed the flat wire through the opening of the luminaire and connect
it to the LED circuit board.
3. Stick the double-sided adhesive tape to the bottom of the glass.
Remove the liner film from the adhesive tape and glue on the flat
wire in a straight line.
4. Connect the flat wire to the adapter and mount the adapter.
Wooden shelf without electrification
Production drawings are available
for downloading on www.visplay.com
or can be received on request.
Drawing no.
229-885 620 mm
229-886 995 mm
229-887 1245 mm
Production drawings of wooden
shelves are available for downloading
on www.visplay.com or can be
received on request.
Drawing no. 286-517
Wooden shelf dimension for bracket concealed 987-348.31 and bracket for side hanging rail 987-881.01/.30
Distance to back panel

14
Invisible6P/L
90°
A
max.
20 kg
1/2019 (EN)
EN Glass shelves (safety glass) 6 mm with cutouts
to be inserted into the profile.
The cutouts make it possible to insert further stepped brackets
(987-881.01/30) for side hanging rail.
Production drawings of glass shelves
are available for downloading on
www.visplay.com or can be received
on request.
Drawing no. 374-263
Universal bracket for Invisible  P/L
 Lift the bracket slightly and insert it into the profile at a °
angle until you reach the limit stop.
 Fix the universal bracket into place with the locking lever.
Check that it is correctly secured.
locked open
Single power adapter for Invisible  P/L
 Insert power adapter into profile at a
° angle until limit stop is reached.
2. Lock adapter in place by pressing the
catches at the side.
Careful handling with merchandise support for Invisible  P/L
 Lift the merchandise support slightly and insert it into the
profile at a ° angle until you reach limit stop A.
Release the merchandise support and check that it is cor-
rectly secured. Do not try to force it to the left or right.
Shelf with lighting for Invisible  P/L
In order to avoid any damage to the contact on the
electrical adapters, it is important that the shelf is
slightly inclined downwards when inserted into the
electrical profile.

15
Invisible6P/L
40 40
28
1/2019 (EN)
EN
Invisible  P/L profile
When attaching supports or shelves, please observe a min.
distance of mm to the power adapter (left-hand side of
profile).
Warning: Only use the conductor rail for shelves with ligh-
ting and for low voltage appliances up to watts (V).
Weight loads
The indicated weight loads are always based on the total weights of the merchandise support and goods.
Please note that max. permissible load decreases as the merchandise support increases in length.
Please note that the inclination of the merchandise support changes with an increase in load. Dierent weights on the merchandise sup-
ports result in an uneven overall appearance of the goods display.
Please note that the weight limit can be reduced considerably when mounting in glass and sheet metal.
The max. permissible load of the Invisible 6 P/L depends on the nature of the wall, the number of fastening points as well as the fastening
material used. All fastening points are to be used in event of a maximum weight load.
Please also observe the weight loads indicated in our sales documentation.
Max. load
Profile per 625mm 40kg
Holder set per holder 20kg
Front arm Ø25mm 25kg
Front arm 30 x 15mm 25kg
Front arm Ø12mm 10kg
Front arm 4mm 10kg
Hook Ø7.5 mm 2kg
Hanging rail Ø 25 mm, 600 mm T arm for use in Invisible6P/L holder set 20kg
Hanging rail Ø 15 mm, 390 mm T arm for use in Invisible6P/L holder set 10kg
Hanging rail 30 x 15 mm, 600 mm T arm for use in Invisible6P/L holder set 20kg
Hanging rail 20 x 10 mm, 390 mm T arm for use in Invisible6P/L holder set 10kg
Support bracket for wooden or glass shelf for use in Invisible6P/L holder set 20kg
Bracket for hanging rail Ø 25 mm per bracket 20kg
Bracket for hanging rail Ø 15 mm per bracket 10kg
Bracket for hanging rail 30 x 15 mm per bracket 20kg
Bracket for hanging rail 20 x 10 mm per bracket 10kg
Bracket for wooden shelf per bracket 20kg
Bracket for glass shelf per bracket 20kg
Bracket 4 mm for wooden shelf per bracket 10kg
Bracket Ø  mm for wooden shelf per bracket 15kg
Angled shelf 15kg
Hook rail for ties, belts etc. 10kg
Universal bracket 20kg
Fixing set for Invisible6P/L profile 20kg
Glass shelf 6 mm with cutouts (374-263) 15kg
Glass shelf 6 mm (286-617) 20kg
Glass shelf with LED lighting kg
Aluminium shelf with LED lighting kg
Fixing set for InvisibleP/L profiles
To be screwed to the back of wooden panels.
Cannot be used in Invisible 6P/L holder set.

16
Invisible6P/L
1/2019 (EN)
EN