visplay Stripes User manual

play it smart
Stripes
Assembly and operating instructions

2
General Instructions
1/2019 (EN)
EN Visplay products are manufactured according to the
latest technology and comply with valid rules and
regulations.
Nevertheless, these products can cause injury or
damage if:
• the product is improperly installed
• the product is improperly used
• the product is improperly altered or modified
• original accessories are not used
• the safety regulations are not observed.
⚠WARNING
Each person involved in the planning, installation
and/or use of our products must be carefully read
and observe these instructions of use.
The following are of course also valid:
• Relevant accident prevention regulations
• Generally recognized safety rules
• National regulations – please consult Visplay if there
is a discrepancy with the Assembly manual
Safety instructions
⚠WARNING
When playing, children often incorrectly assess
danger. You must therefore make sure that your
store fittings are not used as toys.
Please pay attention to the following points:
• Structural conditions, in particular the design and
bearing capacity of walls, ceilings and floors. If
bearing capacity for the specified tractive or pressure
load cannot be achieved by suitable fastening or
stabilising elements, please refrain from installation.
• All the structural components supplied for stabilising
structures are to be used in an unrestricted manner
and must not be removed.
• The products may only be loaded after all the
installation steps have been completed.
• Merchandise supports should be loaded as evenly as
possible.
• Avoid loading in fits and starts.
• The maximum weight loads is to be observed. This can
be found in the instructions on assembly and use, as
well as in our sales documentation.
• Furniture with castors is generally much more unstable
than furniture with glides. Tall, heavy structures on
castors should thus be avoided.
• The recommendations of your safety ocer should
also be observed.
General care for chrome, silk and pearl
In clothing retail applications, frequent dragging of
clothes hangers along the surface can cause slight
abrasion to their hooks. This eect is most pronounced
- more so than with front-on horizontal or inclined-pole
displays - where garments are hung side-on such that
hangers have to be moved more frequently. To prevent
garments from becoming soiled, cleaning of the hanging
rods is essential.
This abrasion can be considerably reduced by using a
coat hanger cover (scliss, 929-449.02).
No responsiblity can be accepted for damage caused by
soiling, as the above mentioned abrasion depends on the
material of the coathangers in use.
With powder-coated surfaces subject to frequent use,
use of special paints is recommended. We will be happy
to advise you.
Use and care of merchandise supports
with anodised aluminium surfaces
Visplay merchandise supports with anodised aluminium
surfaces are hard-wearing. However, the exchange of
accessories might cause slight marks on the surface.
Accessories with plastic inserts usually cause less wear or
none at all.
To remove the marks, we recommend using cleaning
agents ranging from pH 5–8 (do not use any detergents
with acidic or alkaline reaction). Clean by washing the
surfaces using a sponge and water containing a wetting
agent. Then remove any loose or greasy dirt. Rubbing
o the surfaces with detergent using pure cotton waste
or porous cleaning tissue and applying the necessary
pressure in rubbing direction will remove the marks.
Aluminium profiles with widths exceeding  mm must
be subjected to abrasive cleaning using detergents
specifically developed for this purpose. The cleaning
agents developed for abrasive cleaning contain very
finely ground neutral polishing agents and have to
be adapted to the oxide layer. Alternatively, cleaning
can be carried out using an abrasive fibrous web (e.g.
Scotch-Brite, type A, red, fine or very fine) in combination
with a non-abrasive detergent.
Subsequently, residual cleaning agents should to be
rinsed o using a sponge and clear water. Then rub o
the part with a chamois.

3
Stripes 13
1/2019 (EN)1/2019 (EN)
EN
Assembly dimensions / Layout
The choice and arrangement of the profiles must be adapted to the respective assortment and expected load.
Stripes can be fixed on to curved panels (radius >  m). Profile cannot be pre-curved.
Please observe the indications concerning weight loading and ensure that the substructure of the wall units/furniture and their fixtures can
support the expected loads.
With free-standing furniture, ensure that there is sucient stability even with the intended merchandise supports.
When installing in glass, safety glass must be used.
Distance of holes
Assembly dimensions Stripes
Wood: mm
Safety glass: min.  mm
Rabbet size for wood Rabbet size for glass
Layout
Panels and sub-structures must be toughened against bowing. Wooden ledges or angle
sections are suitable for this purpose.
glued and screwed

4
Stripes 13
max. 2 Nm
R min. 6 m
40
1/2019 (EN)
EN
Assembly instructions
Stripes profiles will be screwed.
Please note that the attachment exerts pressure
and friction on soft wall types (e.g. textured wall-
paper) and can damage them.
Stripes can be attached on curved walls
(radius >  m). Profile cannot be pre-curved.
The torque must be observed to ensure the
correct functioning of Stripes13.
Fixing set for Stripes profiles
To be screwed to the back of wooden panels.
Examples on wooden panel
Examples on glass panel

5
Stripes 13
1.5°
625
70
45
589
1250
1245
987-048.48
987-048.48
620
1/2019 (EN)1/2019 (EN)
EN
Instructions of use
With Stripes, the suspension arm of the merchandise support is inserted into the profile at an angle and then lowered down.
Merchandise support slightly inclined (°).
Max. load
Profile per  mm kg
Short profile (/ mm) kg
Front arm Ømm kg
Bracket for hanging rail Ømm per bracket kg
Side hanging frame Ømm kg
Brackets (wooden/glass shelf) per bracket kg
Front arm Ømm kg
Bracket for hanging rail Ømm per bracket kg
Bracket Ømm (wooden shelf) per bracket kg
Clamp bracket (glass shelf)) per bracket kg
Hat arm kg
Hook Ømm kg
Shoe shelf kg
Fixing set kg
The indicated weight loads are always based on the total weights of the merchandise support and goods.
Please observe that max. weight loading decreases as the merchandise support increases in length.
Please observe that the inclination of the merchandise support changes with an increase in load. Dierent weights on the merchandise
supports produce an uneven overall appearance of the goods display.
Please note that the weight limit can reduce considerably when Stripes 13 is used in glass and sheet metal.
Please also observe the weight loads indicated in our sales documentation.
Weight loading
Bracket for wooden or glass shelf - with side hanging frame or with bracket for hanging rail
Bracket for hanging rail Ø
Side hanging frame Ø
Hanging rail Ø

6
Stripes 16
13
17
L = 3100 mm
lto = min. 250 max. 3100 mm
Dim X =
lto– –1
2
x 76.2
round up to a hole number
76.2
lto
L
lto
25 ( 27 )
76.2
40 x 76.2 = 3048
X X
76.2
1/2019 (EN)
EN Assembly dimensions / Layout
The choice and arrangement of the profiles must be adapted to the respective assortment and expected load.
Stripes can be fixed on to curved panels. The profile must be pre-curved for radii between  and mm. With radii >  mm it is not
necessary to pre-curve profiles.
Please observe the indications concerning weight loading and ensure that the substructure of the wall units/furniture and their fixtures can
support the expected loads.
With free-standing furniture, ensure that there is sucient stability even with the intended merchandise supports.
Distance of holes
On-site ma-
sonry
Assembly instructions
With radii greater than mm,
pre-curving is not necessary.
Inner radius
Ri > mm Outer radius Ra > mm

7
Stripes 16
18.9
59.5
10010025
(75)
ø 5.2
8.5
3100 mm
lto = min. 250 max. 3100 mm
min. 50
min. 50
20.2
17
1/2019 (EN)1/2019 (EN)
EN
Wood
Plasterboard
Dimensions Stripes  profile for attachment from the front, for walls (gypsum/drywall, concrete, brick, wood)
• Dimensions of holes
All fixation points are to be used with maximum loads.
• Assembly
• Fastening examples
Depending on the type of wall the profil can be attached with dierent
fixation material.
The max. weight load of the Invisible P/L profile depends on the
nature of the wall, on the number of fixation points as well as on the
fixation material used.
With wooden substructures, a screw length of min.  mm must be
observed.
For mounting on plaster, the following dowels are recommended
(manufacturer Hilti):
• Hollow toggle plug HTB-S Mx
• Hollow plug HHD-S M/x
Please observe the information on the loading values and ensu-
re that the substructure of the wall installation and its fastenings
can cope with the expected loads.
>The correct size and type of anchor fixings must be used to suit
the construction conditions.
>Check anchor fixing as specified by manufacturer.
>All mounting points must be used.

8
Stripes 16
52
M5
ø 12
80
60 16–21
929-178.21
323-813.05
max. 2 Nm
ø 12
Set 929-187.21
10
16
12
ø 10
323-813.05
1/2019 (EN)
EN
The Stripes Profile must be fitted immediately after the adhesive
has been applied. The screw can then be turned in the liquid -
and not hardened - adhesive.
Please observe correct assembly.
Additional use of Fischer adhesive enables full weight loading -
once it has hardened.
Assembly wooden panel
For front attachment to cavity walls, the fixing set - is
to be used.
• Drill Ømm hole.
• Insert cavity dowel (fixing set -) using pliers (Recommendation: Cavity pliers HM z from Fischer®) and expand.
• Unscrew the pre-assembled screw.
• Add Stripes profile and secure with aforementioned screw.
• Assembly has been correctly completed when the screw has been tightened up as far as possible ( Nm).
When using the fixing set (929-178.21), the max. permis-
sible weight per front arm is reduced to 15kg.
Assembly glass
A special fixing set (929-187.21) is to be used for assembly on
glass.

9
Stripes 16
max. 2 Nm
1.5°
40
1/2019 (EN)1/2019 (EN)
EN
Instructions of use/ Care
With Stripes, the suspension arm of
the merchandise support is inserted
into the profile at an angle and then
lowered down.
Merchandise support slightly incli-
ned (°).
The indicated weight loads are always based on the total weights of the merchandise support and goods.
Please observe that max. weight loading decreases as the merchandise support increases in length.
Please observe that the inclination of the merchandise support changes with an increase in load. Dierent weights on the merchandise
supports produce an uneven overall appearance of the goods display.
Please note that the weight limit can reduce considerably when Stripes 16 is used in glass and sheet metal.
Please also observe the weight loads indicated in our sales documentation.
Weight loading
Max. load
Profile per  mm kg
Fixing set per fixing point kg
Front arm Ømm kg
Bracket for hanging rail Ømm per bracket kg
Side hanging frame Ømm kg
Brackets (wooden/glass shelf) per bracket kg
Front arm Ømm kg
Bracket for hanging rail Ømm per bracket kg
Bracket Ømm (wooden shelf) per bracket kg
Clamp bracket (glass shelf) per bracket kg
Hat arm kg
Hook Ømm kg
Shoe shelf kg
Fixing set kg
Fixing set for Stripes profiles
To be screwed to the back of wooden panels.
Assembly instructions
Stripes  profiles will be screwed.
Please note that the attachment exerts
pressure and friction on soft wall types (e.g.
textured wallpaper) and can damage them.
The torque must be observed to ensure
the correct functioning of Stripes16.

10
Stripes 16
1/2019 (EN)
EN