Vista VPSU2488INTe User manual

Ref: VPSU2488INTe
24V AC
POWER SUPPLY
VPSU2488INTe MANUAL
24V AC 8A (8 X 1A PTC FUSED OUTPUT)
Thank you for choosing this high quality 24V ac 8A power supply. Before
attempting to connect or operate this product please make sure you carefully read
these instructions for your safety.
General:
A 24V ac power supply capable of delivering fully rated current to load, housed within a low profile metal
enclosure it is suitable for internal use only. It is provided with 8 individually PTC fused outputs ideal for
low powered CCTV installations.
INSTALLATION AND SET-UP
This unit is only suitable for installation as permanently connected equipment and MUST be fed from a
mains power source having a separate (approved) disconnect device - fitted with a fuse or other over-
current protection device rated at 3A maximum. Ensure that the disconnect device used has appropriate
earth fault protection to the applicable standard.
The enclosure is NOT SUITABLE for external use; bushings should meet a minimum flammability
specification of UL94 HB.
The PSU should be installed according to all relevant safety regulations.
1) Fix to wall or other support structure using the screws/fixings supplied or use appropriate types for
the surface it is being mounted to.
2) Mains input cable must be to the applicable standard with a 3A or greater current capacity, having a
minimum operating voltage of 300/500 Vac.
3) The low voltage output cable must be correctly sized to carry the rated load current to the devices
connected to the PSU.
4) Mains input and low voltage output cables should be routed to use different entry/exit holes in the
enclosure.
5) To comply with current BS EN60950 safety legislation the supplied cable ties must be used to secure
mains input and low voltage output wiring.
Norbain SD Tel: [phone]
210 Wharfdale Rd, Fax: [phone]
Winnersh Triangle, Web: www.vista-cctv.com
Wokingham, Berkshire,
RG41 5TP, UK.

2
Ref: VPSU2488INTe
OPERATION
This unit is intended for use by Service Personnel only - There are NO USER SERVICEABLE parts inside.
MAINTENANCE
There is no regular maintenance required of this PSU.
If the output of the PSU fails the cause of the failure should be investigated e.g. short circuit load. The
fault should be rectified before restoring power to the PSU. The PTC fuses used in this product will
reset automatically once the fault has been rectified.
DISPOSAL OF PRODUCT AT END OF LIFE
This product falls within the scope of EU Directives 2012/19/EU Waste Electrical and Electronic
Equipment (WEEE). At the end of life, the product must be separated from the domestic waste stream
and disposed via an appropriate approved WEEE disposal route in accordance with all national and
local regulations.
For more information see: www.recyclethis.info
SPECIFICATION
Input
Voltage
230V ac nominal (+10% / -15%)
Frequency
50Hz
Fuse (terminal Block)
T3.15A - 20mm 230V HRC Type
Output
Nominal Voltage
24V ac (@ 230V ac input)
Voltage Range
23V ac to 28V ac (on full load to off load @ 230V ac)
Note: Please factor this load ‘Voltage variance’in when designing systems
Output Fuses (x 8)
PTC (auto resetting)
Holding Current: 900mA (@ 20°C Ambient)
Trip Current: 1.8A (@ 20°C Ambient)
Physical
Environment
-10 to +40°C (operating) 95% RH non-condensing
-20 to +80°C (storage)
Enclosure Dimensions
Type
300H x 240W x 55D (mm)
Key lock (provided with 2 keys)
Weight
Approx 4.2Kg

3
Ref: VPSU2488INTe
CONNECTIONS
Input
L
E
Mains Input: Live (Brown)
Earth (Green/Yellow)
N
Mains Input: Neutral (Blue)
Outputs 1 - 8
+
24V ac @ 1A max (no polarity)
-
LOCAL INDICATORS
8-way Fused Output Module
Red LED on
Red LED off
Healthy
Fault Present
COMPLIANCE
This product meets the essential requirements of the following EU Directives:
Low Voltage: 2014/35/EU
EMC: 2014/30/EU
RoHS2: 2011/65/EU
WEEE: 2012/19/EU

4
Ref: VPSU2488INTe
Enclosure
Mounting Hole
Dimensions
Note: Not to scale.
173mm
250mm