Vitek Transcendent Series User manual

VITEK
VITEK
VT-TPTZ20HR-2PNS
Transcendent Series
2 MegaPixel
1/2.8” 20x PoE+ IP
Speed Dome Camera
QUICK START GUIDE
FEATURES
• 1/2.8” 2MP Sony STARVIS® CMOS Progressive Scan Sensor
• Superior Image Quality via High MTF 20x Zoom Lens and STARVIS®
to Capture Vivid Color Images in Low Light Conditions
•Max 30fps @ 2MP
• True WDR (Wide Dynamic Range)
•H.265 / H.264 / MJPEG
• High Efficiency Video Coding (H.265, ITU-T VCEG)
•Smart IR (2.0) with up to 500 foot IR Range
• Smart IR Lighting Sub-System, Improves Uniformity of Illumination
•5.5-110mm Focal Length, 20x Optical Zoom Lens
• Zoom Speed Approximately 3.5s (Optical Lens, Wide-TELE)
•Aperture Range: F1.6 (Wide) to F3.5 (TELE)
• Day / Night w/ IR Cut Filter
• Smart Thermal Management (1.0), with a Built-In Temperature Sensor,
Highly Efficient Turbo Fan, and High Power Heater
• Built-in Micro SD Card Slot, Supporting up to 128GB
• 360° Endless Pan Range, and Pan Speed from 0.1°/s to 80°/s
• ONVIF Compliant with Zero Configuration
• 12VDC @ 3amps / PoE+ (20 watts)
• 12VDC Power Supply Included
• Optional Mounts: VT-TPT20HR-WM (Wall), VT-TPT20HR-PM
(Pendant), VT-TPT20HR-FM (Semi-Flush), VT-TPLMT-W (Pole Mount -
White), and VT-TCNMT-W (Corner Mount - White) Available
• IP 66 Ingress Protection
• 3-Year Warranty
*Sony STARVIS® is a registered trademark of Sony
PLEASE NOTE:
Complete User Guide, Software, Tools, and Updates are
available online. Scan the QR Code or visit:
http://www.vitekcctv.com/Downloads
*Shown with
optional wall mount
VT-TPT20HR-WM

2 3
Cable Connections
Overview
First connect the Waterproof Cap to an Ethernet patch cable, then connect the cameras
ethernet adaptor. If not powering the camera with PoE+, also connect the power Cable
to an approved 12VDC Power Supply.
Weather Resistant Network Coupler
1. Loosen the nut from the Weather Resistant Network Coupler,
2. Run ethernet cable through coupler, then attach a RJ-45 connector.
3. Tighten the nut and coupler for a weather resistant seal.
1 Ethernet connector
2
3 Safety wire
Power connector
1
2
3
Network Cable
DC12V

3
Installation
Installation Using Wall Mount VT-TPT20HR-WM
(mount sold separately) *see rear page 10 for mount dimensions
Before beginning, make sure that the wall or ceiling is strong enough to
withstand the weight of the camera, and that the power is off.*Wall mounting
instructions are below, followed by ceiling mounting and semi-flush mounting.
Insert amicro
SD card
MicroSD Card
Installation
1. Loosen the cover’s 4 screws
and remove it.
2. Insert a microSD card as
indicated (right) and re-install
the cover.
1. Pull the cables through
the bracket.
2. Secure PTZ Camera to
bracket with screws.
3. Drill screw holes in the
wall according to drill
template, then insert
plastic plugs into holes.

4 5
Installation Using Ceiling / Pendant Mount -
VT-TPT20HR-PM (mount sold separately)
*see page 10 for mount dimensions
Adapter tube
1. Install the ceiling mount according to the following diagram:
2. Mount the adapter tube to the
bracket and secure it with a screw.
3. Secure the pendent mounting
bracket to the ceiling.
1/2”
4. Insert two screws in
the holes as indicated in
figure (3.) and leave.5”
clearance.
5. Connect the cables
and hang the bracket on
the wall.
6. Attach the bracket to
the wall with four screws.

5
Installation Using Semi-Flush Ceiling Mount
VT-TPT20HR-FM (mount sold separately)
*see page 10 for mount dimensions
4. Connect cables, then hook the
safety wire to the adapter stem.
5. Securely attach the camera
to the adapter stem with screws.

6 7
Attach
8.35”
s Thr
8.35
LAN Configuration
The camera can be accessed on the local network either using the
IP-Tool or directly in a web browser.
Accessing the Camera Using the IP-Tool
1. Make sure the camera and PC are connected to the LAN.
2. Locate the IP-Tool installer at www.
vitekcctv.com/Downloads/Soft-
ware/Transcendent-IPTool_v2.0.2.zip
, then install on the PC. Open
the installed application.
3. Modify the IP address. The default IP address is 192.168.226.201.
Click the information of the camera listed in the above table to show
the network information on the right side. Modify the IP address and
gateway of the camera and make sure its network address is in the
same local network segment as the computer’s. Please modify the
IP address of your device according to the practical situation.
For example, the IP address of your computer
is 192.168.13.4. So the IP address of the
camera shall be changed to 192.168.13.X.
After modification, please input the password
of the administrator and click “Modify” button
to modify the setting.
** Default admin password: “123456".
MENU
Network Cable Network Cable
Switch
Router Computer
P T Z C amer a

7
LAN Configuration
The camera can be accessed on the local network either using the
IP-Tool or directly in a web browser.
Accessing the Camera Using the IP-Tool
1. Make sure the camera and PC are connected to the LAN.
2. Locate the IP-Tool installer at www.
vitekcctv.com/Downloads/Soft-
ware/Transcendent-IPTool_v2.0.2.zip
, then install on the PC. Open
the installed application.
3. Modify the IP address. The default IP address is 192.168.226.201.
Click the information of the camera listed in the above table to show
the network information on the right side. Modify the IP address and
gateway of the camera and make sure its network address is in the
same local network segment as the computer’s. Please modify the
IP address of your device according to the practical situation.
For example, the IP address of your computer
is 192.168.13.4. So the IP address of the
camera shall be changed to 192.168.13.X.
After modification, please input the password
of the administrator and click “Modify” button
to modify the setting.
** Default admin password: “123456".
MENU
Network Cable Network Cable
Switch
Router Computer
P T Z C amer a

8 9
4. Double-click the IP address and then the system will pop up the web
browser to connect IP-CAM . IE browser will download the Active X
control. After downloading, a login window will pop up as shown
below:
Input the user name and password to log in.
Default user name: admin / Default password: 123456.
Directly Access Through a Web Browser
The default network settings are as shown below:
IP address: 192.168.226.201 HTTP: 80
Subnet Mask: 255.255.255.0 Data Port: 9008
Gateway: 192.168.226.1
You may use the above default settings when you log in the camera for
the first time.
1. Manually set the IP address of the PC. The network segment should
be the same as the default settings of IP-CAM. Open the network
and share center. Click “Local Area Connection” to pop up the
following window.
Select “Properties” and then select Internet protocol according to the
actual situation (for example: IPV4). Next, click “Properties” button to
set the network of the PC.
2. Open the IE Browser and input the default address of IP-CAM and
confirm. The IE browser will download Active X control.
3. After downloading Active X control, the login dialog box will pop up.
4. Input the default username and password and then enter to view.
WAN Configuration
Access the camera by the router or virtual server for example.
1. Make sure the camera is connected to the LAN; Then log into the
menu to set up the port number.
the IP address.
4. Open the web browser and input its WAN IP and HTTP port to
access the IP-CAM.
3. Go to the router’s management interface through IE browser to
forward the IP address and port of IP-CAM in the “Virtual Server”.

9
2. Open the IE Browser and input the default address of IP-CAM and
confirm. The IE browser will download Active X control.
3. After downloading Active X control, the login dialog box will pop up.
4. Input the default username and password and then enter to view.
WAN Configuration
Access the camera by the router or virtual server for example.
1. Make sure the camera is connected to the LAN; Then log into the
menu to set up the port number.
the IP address.
4. Open the web browser and input its WAN IP and HTTP port to
access the IP-CAM.
3. Go to the router’s management interface through IE browser to
forward the IP address and port of IP-CAM in the “Virtual Server”.

10 11
Installation Mount Dimensions
VT-TPT20HR-FM
VT-TPT20HR-PM
VT-TPT20HR-WM 3.32”
4.57” .39”
9.72”
6.30”
7.22”
2.48”
3.51”
2.48”
2.54”
9.17”
9.17”
5.10”
9.17”
mm
mm
mm
mm
7.20”
mm
mm
mm
6.89”
1.89”