Vitek VT-8P125 User manual

VITEK
VITEK
FEATURES
• Provides 8 - 10/100Base-TX PoE ports & 2 10/100Base-
TX Ethernet Ports
• 125 Watt PoE Power Budget
• Conforms to IEEE802.3, IEEE 802.3u, IEEE802.3af,
IEEE802.3at
• High back-plane bandwidth 1.8Gbps
• IEEE802.3x Flow control
• Surge protection for power port and data ports
• EMI standards complies with FCC, CE class B
VT-8P125
8 Port 125 Watt Compact
PoE Switch

2
Product Layout
Installation
Package Contents:
Extend Function:
Enables 200 meter transmission at 10mbps. Power input port
ON OFF/ DC48V
POE Ethernet Port Up-link Ethernet Port
PWR
Link Active/
Function
Function Ethernet PoE Switch
10
Notice
Please restart device after enabling/disabling the Extend function.
1) Please turn off the PoE Switch & all ethernet devices power before installation to avoid damage,
2) Use network cable to connect PoE IP cameras to ports 1~ 8 respectively
3) Use a network cable to connect equipment via up link port and NVR or computer
4) Connect power adapter
5) Check if the installation is correct and equipment is in good condition and the connection is stable
6) Ensure the Ethernet equipment with power is working properly.
Installation Steps:
8 Ports PoE Ethernet S wit ch
Cat5 5e 6
Cable
Monitor
NVR
PoE PTZ Camera
PoE IP Camera
PoE Dome C amera
PoE IP Camera
power
Application
10 ports PoE Ethernet Switch 1pcs
Power adaptor 1pcs
Ac power cable 1pcs
Accessory 1pcs
User manual 1pcs
(888) VITEK-70 | WWW.VITEKCCTV.COM
28492 Constellation Road Valencia, CA 91355
Detailed Specifications
Ports
PoE Standard
PoE Pin assignment
LED Indicators
Switching capacity
MAC address table
Traffic control
Thermal methods
Input voltage
Power consumption
Operating temperature
8 - 10/100Base-TX PoE Ports / 2 - 10/100Base-TX ports
IEE802.3af, IEEE802.3at, per port 30W(MAX) / Total 130W
V+ (RJ45 Pin 4, 5), V- (RJ45 Pin 7, 8).
PWR, PoE, Link/Act LED
2.0G
4K
IEEE 802.3x full-duplex flow control
Fanless
100V240V AC90/60Hz (for power adapter) / 48VDC (for PoE switch)
130W (125W for PoE)
32º~104ºF (0º~40ºC) / 20~85% RH
8 Port 125 Watt Compact PoE Switch
Preliminary Specifications:
VT-8P125

3
- Please follow these steps if the equipment has trouble
- Make sure the equipment is installed according to the installation guide
- Configure RJ45 cable order meets EIA TIA568A or 568B standard
- Every PoE port can provide maximum power of uo to 30W
- Please contact your vendor if trouble still exists
Troubleshooting
Specifications
Instruments to be used wire crimper network tester Wire sequence of RJ45 plug should
conform with EIA TIA568A or 568B
1 Please remove 2cm long the insulating layer and bare 8 pairs UTP cable
2 Separate the 8 pairs UTP cable and straighten them
3 Line up the 8 pieces of cables per EIA TIA 568A or 568B
4 Cut off the cables to leave 1 5cm bare wire
5 Plug 8 cables into RJ45 plug make sure each cable is in each pin
6 Use the wire crimper to crimp it
7 Repeat above 9 steps to make the another end
8 Use network tester to test the cable if t works
Pin Color
White reenG
Green
Blue
White Orange
White lueB
White Brown
Orange
Brown
1
2
3
4
5
6
7
8
Pin Color
1
2
3
4
5
6
7
8
White Green
Green
Blue
White Orange
White Blue
White Brown
Orange
Brown
EIA TIA 568A EIA TIA 568B
1818
Wiring
(888) VITEK-70 | WWW.VITEKCCTV.COM
28492 Constellation Road Valencia, CA 91355
Detailed Specifications
Ports
PoE Standard
PoE Pin assignment
LED Indicators
Switching capacity
MAC address table
Traffic control
Thermal methods
Input voltage
Power consumption
Operating temperature
8 - 10/100Base-TX PoE Ports / 2 - 10/100Base-TX ports
IEE802.3af, IEEE802.3at, per port 30W(MAX) / Total 130W
V+ (RJ45 Pin 4, 5), V- (RJ45 Pin 7, 8).
PWR, PoE, Link/Act LED
2.0G
4K
IEEE 802.3x full-duplex flow control
Fanless
100V240V AC90/60Hz (for power adapter) / 48VDC (for PoE switch)
130W (125W for PoE)
32º~104ºF (0º~40ºC) / 20~85% RH
8 Port 125 Watt Compact PoE Switch
Preliminary Specifications:
VT-8P125

28492 CONSTELLATION ROAD VALENCIA, CA 91355
WWW.VITEKCCTV.COM
LIMITED PRODUCT WARRANTY
VITEK products carry a three (3) year limited warranty. VITEK warrants
to the purchaser that products manufactured by VITEK are free of any
rightful claim of infringement or the like, and when used in the manner
intended, will be free of defects in materials and workmanship for a
period of three (3) years, or as otherwise stated above, from the date of
purchase by the end user. This warranty is nontransferable and extends
only to the original buyer or end user customer of a VITEK Authorized
Reseller.
The product must have been used only for its intended purpose, and
not been subjected to damage by misuse, willful or accidental damage,
caused by excessive voltage or lightning.
The product must not have been tampered with in any way or the
guarantee will be considered null and void.
This guarantee does not affect your statutory rights.
Contact your local VITEK Reseller should servicing become necessary.
VITEK makes no warranty or guarantee whatsoever with respect to
products sold or purchased through unauthorized sales channels.
Warranty support is available only if product is purchased through a
VITEK Authorized Reseller.
Version 1.0
June 2017