VIVA FITNESS KH63 User manual

USER'S MANUAL
Upright Bike
KH63

1
CONTENTS
1. Considerations 2
2. Tools and accessories 2
3. explosive view and part list····························3/4
4. Installation steps 5
5. Direction For Use 7
6. Maintenance and troubleshooting 10

2
1. To ensure your safe, reliable and comfortable use of this series of
exercise bikes, please read the following important matters and all
operation instructions before use. The company shall not be liable for any
personal injury or property loss caused by the use of this product.
2. Consult your doctor before starting a plan or other exercise program.
This is especially important for people over the age of 35 or with pre-
existing health conditions.
Considerations:
1. This fitness bike is a fixed fitness equipment suitable for the family and an aerobic training equipment for
improving cardiovascular function;
2. The exercise bike should be placed on the flat ground when in use;
3. Before use, please check whether all bolts, bolts and other parts are properly installed and locked;
4. The intubation depth of the cushion cover shall not exceed the minimum depth marker line;
5, please wear appropriate clothes and shoes and socks, please do not wear a dress or too long blouse, so as not to
hook on the exercise car; Strap your feet firmly;
I. When exercising, do not let children approach the exercise bike; The free movement space of the device should
be not less than 2 meters around.
II. Before starting to exercise, please consult your doctor and make a reasonable training plan according to your
condition and exercise goal;
III. If you feel nausea, pain, chest tightness, rapid heartbeat, difficulty in breathing or loss of balance during
exercise, stop exercising immediately and go to see a doctor;
IV. The maximum weight of the user of the machine shall not exceed 100Kg;
V. The braking device of the machine is of non-speed correlation type;
VI. The machine meets the requirements of EN957-5HC class;
VII. The machine is not suitable for medical use.
(1) Children should be supervised to ensure that they do not play with utensils.
(2) This appliance is not intended for use by persons (including children) who are physically weak, slow in response
or have mental disorders, unless it is safely used under the guidance or with the help of a person responsible for
their safety.
Warning: Violation of the above safety regulations will result in personal and equipment injuries.

3
Tools and accessories

4
Explosive View

5
Part list
N
O.
Descripti
on
Q
t
y
N
O
.
Descripti
on
Q
t
y
1
Rear foot tube
1
4
1
Square cap
2
2
Front foot-cover
2
4
2
ARC washer
8
3
Rear foot cover
2
4
3
Pull ROD
2
4
Main frame
1
4
4
adjusting rod
2
5
Front foot tube
1
4
5
Adjust slice
2
6
Front cover
1
4
6
Flat Washer Ф6
3
7
Handlebar support
1
4
7
Spring washer Ф6
2
8
Hand bar
1
4
8
Nut M6
2
9
Ф25Ball plug
2
4
9
Cap nut M8
4
1
0
Foam grip
2
5
0
Bolt M8X16
4
1
1
Meter （239B）
1
5
1
Bolt M8X20
1
1
2
Pulse senser
2
5
2
Cross head screw M5X35
1
1
3
Front plastic cover
1
5
3
Cross head self-tapping screwST4X8
2
1
4
Seat cushion tube cover
1
5
4
Cross head self-tappingscrewST4.2X16
5
1
5
Seat bracket
1
5
5
Cross head self-tapping screwST4.2X20
2
1
6
Meter wire（lower）
1
5
6
BOLT M8X75
4
1
7
Meter wire（upper）
1
5
7
Hexagonal self-locking nut
2
1
8
Heart rate wire
1
5
8
Flat Washer Ф8
3
1
9
Seat cushion
1
5
9
Spring washer Ф8
11
2
0
Right cover
1
6
0
Flat Washer Ф5
1
2
1
Rightcover
1
6
1
Nut M8
6
2
2
crank
1
6
2
stator
2
2
3
Belt wheel
1
6
3
BOLT M6X12
1
2
4
reduction sleeve
1
6
4
Cross head self-tapping screw M5X12
1

6
2
5
Spring knob
1
6
5
Pedal belt
2
2
6
Bearing set
1
6
6
Screwdriver S=5
1
2
7
Pressing wheel bracket
1
6
7
Multiple wrenches
1
2
8
Pressing belt wheel
1
6
8
Wrench
1
2
9
4V Belt
1
6
9
3
0
Flywheel
1
7
0
3
1
8-section tension control
1
7
1
3
2
resistance cable
1
7
2
3
3
Pedal(Left & Right)
2
7
3
3
4
Handbar cover
1
7
4
3
5
Spacer
1
7
5
3
6
T knob
1
7
6
3
7
Crank Decorative Cover
2
7
7
3
8
Hole plug
2
7
8
3
9
shot knob
2
7
9
4
0
Seat cushion adjustable bracket
1
8
0

7
Installation steps
2. With 2 sets M8×75 bolts（56）、Ф8 spring washer（42）、Ф8 flat washer
（59）、M8 cap washer（49）attach front foot tube（5）on main frame（4
）。
3. With 2 sets M8×75 bolts（56）、Ф8 spring washer（42）、
Ф8 flat washer（59）、M8 cap washer（49）attach rear foot tube
a. on main frame（4）。
3.
A. Connect the connector (16) and (17) of the upper and lower sections of the electronic table connection, and
then connect the terminal terminal of the lower end of the eight-section spinner body (31) firmly with the output
fine-tuning connection (32). (Note: first of all the output adjustment knob to the "+" direction to the end (at this
time the output of the spinner terminal extension to the longest), according to the figure of the joint terminal
sleeve in the output adjustment wire connection hook, pull up, the output adjustment of the upper end stuck into
the box slot. If the upper end of the output fine adjustment body line cannot just be stuck into the adjustment box
slot, please turn the lower end of the adjustment box nut to the appropriate position, so that the output fine
adjustment body line at the top of the clip just stuck into the adjustment box slot. (See Figure 3-A, B and C)
B: hand over weldment (7) set into the frame (4) to take over by 4 sets of round head hex socket bolts M8 x 16 (50),
spring washer Ф8 (59) and curved washer Ф8 (42) will hand over weldment (7) connected to the frame (4) tighten.
(See Figure3-D)

8
4.
a. Insert the heart rate line (12) through the side hole on the
handlebar welding part (7) and through the upper end; Then cover the
heart rate line (18) with the threading hole plug (38), plug the hole on
the welding joint (7), and then cover the hand handle pipe (8) in the
clamping tube hoop on the welding joint (7), as shown in the figure,
then cover the overhand handle decorative sleeve (34) and the spacer
sleeve (35), and lock it with the hand-wheel (36).
b. Connect the electronic meter wire (11) and heart rate wire (16) to
the corresponding connector of the electronic meter, and then put the
extra wire plug into the tube welding part (7); Then, the protrudent
side of the electronic watch is set to the welding seam of the forehand
connector, the upper end of the electronic watch is fixed to the hand
connector (7), and is fixed with the cross-groove disc head screw
M5X10 (64).
Note: the clamping teeth on the handgrip pipe (8) must be consistent with the clamping groove of the tube
hoop of the handgrip welding part (7).
5.
With 3 sets of nylon nut M8 (61), spring washer Ф8 (59), flat washer Ф8 (58)
install the seat cushion (19) on the seat cushion adjustment frame (40).
6.
（
1
）
Then insert the seat cushion welding piece (15) into the D-shaped transition sleeve (14), insert the
seat cushion welding piece (15) into the seat support pipe of the host frame (4), and align the upper end rotary
hand seat hole of the seat support pipe of the host frame (4) with a certain hole

9
on the seat cushion welding piece (15); Then insert the stretch hand
(25) into the hole and tighten the handwheel. (See Figure 6)
（ 2 ） Put the seat cushion adjusting frame (40) on the upper
end of the seat cushion adjusting frame (15) according to the
direction shown in the figure. After adjusting a certain position, use
the seat cushion adjusting handwheel (39) to lock up.
REMARK：1. To adjust the high and low position of the seat cushion (20), only the stretch hand
(27) should be unscrewed. After adjusting the seat cushion support (16) to the appropriate position, then tighten
the handwheel with force;
(1) To adjust the front and rear positions of the seat cushion (20), just unscrew the seat cushion to adjust the
handwheel (64). After adjusting the seat cushion support (16) to the appropriate position, tighten the handwheel
with force;
(2) If the cushion is found to be skewed, loosen the fixing nut at the lower end of the cushion, adjust the
cushion to the correct position, and then lock it tightly.
7.
Fasten the two foot straps (65) on the left and right foot straps (33) first, then mount
them on the crank (22) of the rack and screw them down. (see figure 8)
Note: left (L), right (R) are indicated on the foot pedal shaft.
When stamping quickly in one direction, do not immediately kick in the other to
avoid injury.
Instructions
1, load adjustment: resistance fine tuning knob, clockwise rotation, resistance increase, according to your own
needs to adjust the level of resistance.
1. Adjusting the height of the seat: loosen and pull back the hand screw on the seat cushion cannula, lift or lower
the seat cushion tube to an appropriate position according to the needs of the wearer. Then, the hand screw will
be automatically inserted into the seat cushion tube hole to tighten the hand screw.
2. When riding a bike, sit on the cushion, fasten the pedal strap and hold the handle with both hands. The upper
body can freely change its position according to the strength of both legs and riding speed.

10
METER：
1、A, functionality, 2 、1. Speed:
Display in window A. The measurement is instantaneous speed, reflecting the speed
of running, and the measurement range is 0.0 to 99.9 km/h. (or Max. 1500 RPM).
3、2. Time: B window display. 4、(1) Measure
the accumulated time of motion
5、The time taken from the start of motion to the stop of motion is measured in a range of 0~99 minutes and 59
seconds, and the timing is timed for 3 seconds without motion.
6、(2) Time alarm function
7、First, set the running time. After the start of the run, the time will be counted backwards, and the timer will
go off for 10 seconds until zero. The maximum setti ng time will be 99 minutes.
8、8. Distance: C window display.
2. Measure the cumulative distance of running
Measure the distance run from start to stop. The measurement range is 0.00~9.99~99.9 km, and it will be
automatically converted to display with 1 decimal place when the meter reaches 9.99 km.
3. Distance alarm function
First, set the running distance. After the start of the running, the distance will be counted backwards and then
reduced to zero for 10 seconds. The maximum setti ng value is 99.9km.
9. Calories: D window display.
14. Measure the cumulative heat consumption of exercise
Measure the quantity of heat consumed from the beginning to the end of the movement (that is, calories), the
measurement range is 0.0~99.9~999 kcal, which will be automatically converted to integer display after 99.9 kcal is
fully counted.
15. Calorie alarm function
First set the number of running calories consumed, after the start of the run, the calorie count, counting down to
zero alarm for 10 seconds, the maximum set value is 999 kilocalorie.
10: Heart rate: E window display
By holding the heart rate sensor, the heart rate per minute is measured with a range of 40~240 beats per minute.
When there is no heartbeat signal for 25 seconds, it will automatically display "P", indicating that the heart rate test
is suspended; Press any key to change "P" to "0", indicating the heart rate can be measured.
11: Wheel circumference
The wheel diameter has been set to 60 (or set to a size as required by the manufacturer).

11
12: There are key sounds when operating MODE key, SET setti ng key or RESET RESET key.
Stand still for 8 minutes (no operation, no movement), the meter will be automatically shut down and reset all data,
and the treadmill will be displayed automatically by pressing the button or starting the treadmill.
6. Installation method
• Remove the battery door on the back shell of the meter and install two new 1.5VAA batteries in the positive and
negative directions of the battery box (for battery products not installed).
• Fix the instrument on the pipe in front of the fitness equipment with screws.
• Connect the sensor wire plug with the outlet connector on the back of the instrument or insert the signal input
jack on the back of the instrument.
• Quick step on the fitness equipment and the displayed speed changes indicate that the installation is qualified;
otherwise, check whether the magnet seat and the sensor are installed correctly and whether the sensor wire plug
and the lead wire of the watch head are connected reliably.
II:Method of use:
• Press the MODE key to select the display window that needs to be SET or cleared, and the "SET" symbol on
the corresponding window flashes. Press the SET key to SET the alarm time, alarm distance or alarm calories
required. Press the RESET key to clear the corresponding window display value.
• Step on the fitness equipment to start measuring, and observe your exercise parameters according to the
contents displayed in different Windows.
• Heart rate measurement: press any key, then grasp the corresponding position of heart rate sensor metal
plate with the left and right palms respectively (note: each palm should touch two metal plates at the same
time). The monitor in the heart rate display window will show your current heart rate in seconds or less. When
the heartbeat signal is received during the measurement, the heartbeat corresponds to the "astillation". In
order to prevent the influence of palm movements on heart rate measurement and ensure the accuracy of
heart rate measurement, it is suggested that the heart rate measurement should be carried out after the
exercise is suspended or stopped, and the heart rate measurement should not be carried out at the same time
of running.
Hint: Sometimes there will be signal interference when the palm holds the metal sheet. The heart rate
displayed in the first 2~3 seconds may not be correct and appear high, which is a normal phenomenon. Then
the heart rate will return to normal measurement. This method of heart rate detection is mainly helpful to
determine the amount of exercise you do, not as a basis for disease treatment。
III：The battery replacement
When the display darkens or shows no display, remove the battery cover and install two new 1.5VAA batteries in
the positive and negative direction of the battery. Install the battery cover.

12
MALFUNCTIONS AND TREATMENT
(1) Maintenance
1. Regularly check whether the bolts and nuts of each part are fastened, whether the adjusting knob is locked,
whether the rotating part is flexible, and whether there are any worn or damaged parts. Ensure that all parts are in
good condition to ensure the safety of the equipment.
2. Parts that are worn or damaged should be replaced immediately or sent to the maintenance center for
replacement before use after repair.
3. Keep the equipment clean, but do not wipe it with acid, alkaline or organic solution.
b. Troubleshooting
Malfunction
Reas
on
Treatment
Base is unstable.
1. Floor is not flat or there is
small object under the front
or rear stabilizer.
2. The rear base feet have not been
leveled when assembling.
1
.
2
.
Remove the object.
Adjust the rear base feet.
Handlebar or seat
cushion is shaking.
The screws and round knob are loose.
Tighten the screws and round knob.
Loud noise from the
moving parts.
The interval of the parts is improper
tighten.
Open the covers to adjust.
No resistance when riding
■The interval of the magnetic
resistance increases.
■Tension control isdamaged.
1
.
Open the covers to adjust.
the upright bike.
2
.
Change the tension control.
3
.
Open the covers to adjust.

13
■Running belt is slippery.
■The bearing set is damaged.
4
.
Change the bearing set.