Vive Comfort TP-Z-ROSW User manual

A trained, experienced technician
must install this product.
Carefully read these instructions. You
could damage this product or cause a
hazardous condition if you fail to follow
these instructions.
Table of Contents Page
Rev. 1407
® U.S. Registered Trademark. Patents pending.
Copyright © 2014. All rights reserved.
Installing Batteries
Establishing Communication
Specications & Warranty
2
3
Installation Tips 4
5
1
This manual covers the
following models:
• TP-Z-ROSW (Requires Z955W or T955WH)
Caution:
Equipment damage hazard
Do not operate the cooling
system if the outdoor
temperature is below 50˚ F
(10˚ C) to prevent possible
compressor damage.
This remote sensor was designed to the
highest reliability and ease of use standards.
Thank you for choosing our quality products.
OUTDOOR SENSOR & USER GUIDE
Congratulations on purchasing
our Wireless System.
TP-Z-ROSW
COM F O R T
TM
VIVE Comfort
P.O. Box 3377
Springeld, MO 65804
Toll-Free: 1-800-776-1635 Web: www.vivecomfort.com
Hours of Operation: M-F 9AM - 6PM Eastern

2
Installing Batteries
Note about low batteries:
When the outdoor battery needs to
be changed the Master Thermostat
will ash LOW BAT OUTDOOR
as seen on the left.
Installation Tip
Before putting the inside cover back on, proceed to the next page to establish a
connection between the Master Thermostat and this Remote Sensor.
To install 2 AA batteries remove the three screws
shown in the diagram. One in the middle of the inside
cover box, and two on either side of the cover box.
INSTALLING BATTERIES

3
The Master Thermostat Tech setting for the
outdoor remote sensor must be set to YES . See the
master thermostat manual for instructions.
While the Master Thermostat is on the Outdoor Sensor
screen with YES selected, hold down the connection button
on the inside of the Outdoor Remoteuntil the
Master Thermostat shows the letters YE and says
Found Outdoor.
1.
2.
Connecting to the Master Thermostat
Installation Tip
Example Step 2.
The Master Thermostat Found Outdoor Screen.
For installations where the temperature will be frequently below freezing,
battery life may be much better with 2 AA lithium batteries.
Easy, two step communication link set up.
Connection button
located inside the Remote Sensor
Important:
DO NOT press the connection
button again after Step 2 above
has been completed. Pressing
the button a second time will
break the communication link
and the connection steps will
have to be repeated.
ESTABLISHING COMMUNICATION
Inside of Sensor FSK/ ASK Switch
Remember
Our Wireless System contains selectable wireless
communication. Each component has a jumper switch
labeled FSK and ASK. Default setting: FSK. All components
must be set to the same position for wireless communication.
This selectable communication option is available to you in
case you have a device you are pairing with that only has
the ASK option.

4
Mounting the Outdoor Remote Sensor
For vertical mount put
one screw top and one
screw bottom.
For horizontal mount
put one screw left and
one screw right.
Optional horizontal mount
Vertical mount
Wireless Range
Range between the Remote Sensor and the Master Thermostat is approximately100 feet with no
obstructions and approximately 50 feet in standard residential metal, brick, and concrete construction.
Important:
Do not install in
direct sunlight.
INSTALLATION TIPS

VIVE Comfort
P.O. Box 3377
Springeld, MO 65804
5
SPECIFICATIONS & CONTACT INFORMATION
Temperature accuracy
Power source
Transmission
Frequency
± 1ºF
Battery Power from 2 AA 1.5 V Batteries
Every 5 minutes
916 MHz
Specifications
Temperature Range -4º to 140ºF (-20º to 60ºC)
Name: ____________________________
Address: ____________________________
____________________________
City: ____________________________
State: ____________________________
Zip: _____________________
Thermostat Model: _____________________
Date Installed: _____________________
Warranty Registration:
Complete form and mail to:
Thermostat Warranty Registration