viveroo one kiosk Installation and operating instructions

User manual & Installation guide
one kiosk
Viveroo USA
Houston, TX
1-800-541-4830
www.viveroousa.com
REV20200619

Safety Information
One Kiosk, User Manual & Installation Guide Page of2 11
! Warning
Please read the assembly instructions included carefully, and
completely before using your free. Please follow these instructions
and recommendations to ensure proper use and effectiveness.
Safety
Information
The One Kiosk is intended for use in enclosed and dry living spaces.
The following conditions must be provided:
-Operating temperature between 0° C (32° F) and 35° C (95° F).
-Relative humidity (during use): 20 % to 90 %, non-condensing.
-No external environmental influences such as oil, chemicals,
salt,
extensive dust, etc.
Installation, service or repairs, if necessary, may only be performed by
authorized persons.
The maximum altitude is 6,000 feet.
The installer is responsible for selecting the proper mounting location
and safe installation of free flex. This also applies to installation
in
movable surfaces, such as doors. The installer is responsible
for
performing and documenting all necessary safety tests.
All electrical installation work may only be conducted by authorized,
trained electricians, who adhere to all general rules and
regulations applying to electrical installation.
Should it become apparent that safe operation of the Kiosk is
not
assured, then Kiosk must immediately be taken out of service
and
secured against potential misuse. If the Kiosk functions are limited,
blocked or disabled, if an unusual odor is present, if noises such
as
scratching are audible or damage is visible, safe operation can
no
longer be guaranteed.
Care and
Cleaning
Wipe your Kiosk as needed with a soft micro fiber cloth and clear
water only. Dampen the micro fiber cloth and wipe the surfaces gently.
Use stainless steel cleaner to clean the pipe and base.
! WARNING: The interior of the Kiosk must remain dry. To ensure
this, use only a damp cloth for cleansing.
! WARNING: Never scratch, scrape or scrub the Kiosk surfaces
with
abrasive materials.
!

Technical Data
Measurements
in Millimeters
Measurements One Kiosk frames:
… iPad mini 4/5
… iPad 10.2“ (7. Gen; 2019), iPad Air (2019), iPad Pro 10,5“
… iPad Pro 11“ (2018/2020)
… iPad Pro 12.9“ (2018/2020)
225 x 143
272 x 183
270 x 187
303 x 224
Depth of the frame
15
Diameter Standpipe
60
Diameter Standbase
180
Weight in Grams
One Kiosk Frame plus Standpipe, Standbase, and Installation Material:
… iPad Mini
… iPad 10,2“, Air (2019), iPad Pro 10,5“
… iPad Pro 11“
… iPad Pro 12,9“ (2018)
1,830
1,940
1,980
2,340
Electrical
Connections
Power Supply
Power Consumption
100-240Vac, 50-60Hz
12.5
Watts - 18 W
atts depending
on iP
ad and psu
Removal from
Power Supply
The One Kiosk may be removed from the power supply via the circuit breaker in the respective rooms.
CE & Co.
All One Kiosks have CE certification. The One Kiosk is made in Germany. We use only high-quality parts
and components produced by market leaders. The One Kiosk customers are proud of their iPad stand.
Technical changes and mistakes are excepted.
Product
Contents
- User Manual & Installation Guide for the One Kiosk
- One Kiosk frame made of painted aluminum
- Standpipe made of painted aluminum
- Standbase made of painted aluminum with rubber caps
- Closure Cap
- Installation Material: Screws and Felt Points
- Cable: Lightning/USB-C (Depending on the iPad Generation)
Compatability
Electrical operation of the One Kiosk is permitted only in connection with Viveroo or Apple power supply units.
Operation of the Kiosk otherwise will lead to immediate loss of guarantee and warranty.
One Kiosk, User Manual & Installation Guide Page of3 11

Installation
Delivery Contents
Illustrations and texts are exemplary. Depending on the iPad and USB port, other power supplies or cables may be supplied.
1
Mounting the One Kiosk with power cable (Lightning and USB-C)
pp 5-7
2
Mounting the One Kiosk with a PoE Adapter
If you use an iPad Pro with USB-C Adapter in combination with PoE, please directly skip to step 2.6
pp 8-9
3
Mounting of Optional Scanning Module
p 10
One Kiosk with power cable
PoE Adapter (Accessory)
Scanning Module (Accessory)
One Kiosk, User Manual & Installation Guide Page of4 11

Installation
Illustrations and texts are examples that vary on the iPad and USB port, other power supplies, or cables.
1. Mounting of the One Kiosk with a power cable.
If you use an iPad Pro with USB-C cable, the installation works
similarly. You only have a USB-C instead of the Lightning cable.
If you use the One Kiosk with a PoE Adapter, please see step 2 (pp 8-9).
Step 1.1
Make sure that all of the felt points are stuck to the
appropriate place on the cover. Insert the shutter for the
camera cutout.
Step 1.2
Guide the Lightning USB cable through the standpipe.
! Note: Make sure that the cable is inserted so that the
Lightning adapter runs to the beveled side of the tube
and the USB adapter to the right-angled one (the
direction doesn't matter for the USB-C cable for the
iPad Pro).
One Kiosk, User Manual & Installation Guide Page of5 11

Installation
Step 1.3
Screw the standpipe to the stand.
! Note: The stand is mounted on the right-angled side
of the tube.
Step 1.4
Now run the cable through the recess in the cover and
then screw the frame onto the standpipe.
! Note: You can already insert the cable into the cable
duct in this step. The cable should run to the right
side.
! Note: The cover can also be mounted in portrait
format.
Step 1.5
Place the iPad in the holder and insert the Lightning
connector.
! Note: Make sure that the cable is in the intended
cable duct so that the iPad sits straight in the holder.
One Kiosk, User Manual & Installation Guide Page of6 11

Installation
Step 1.6
Cover the Lightning adapter with the closure cap.
Step 1.7
Fix the closure cap with the enclosed screws. The iPad
can no longer be removed from the holder without
loosening the cap.
One Kiosk, User Manual & Installation Guide Page of7 11

Installation
2. Mounting the One Kiosk with a PoE Adapter.
These steps describe the installation of the One Kiosk for iPads
with the Lightning connector in combination with PoE.
! If you use an iPad Pro with USB-C Adapter, please directly skip to step 2.6
Step 2.1
Make sure that all of the felt points are stuck to the
appropriate place on the cover. Insert the shutter for the
camera cutout.
Step 2.2
Guide the PoE adapter through the standpipe.
! Note: Make sure that the cable is inserted so that the
Lightning adapter runs to the slanted side of the tube
and the PoE adapter to the right-angled one.
Step 2.3
Connect the PoE adapter to your LAN cable.
! Note: If the LAN cable has to be connected to your
switch / injector beforehand, run the LAN cable
through the base plate of the one kiosk before.
One Kiosk, User Manual & Installation Guide Page of8 11

Installation
Step 2.4
Screw the stand base to the pipe. The PoE adapter
disappears in the standpipe. So all connections are
hidden and secured.
Step 2.5
Mount the frame now
To do this, follow steps 1.4 - 1.7 (Pages 6 - 7).
Step 2.6
Option
PoE for
USB-C
If you are using an iPad Pro with USB-C connection and
at the same time represent the power and data supply
via PoE, carry out the installation according to step 1.
(Pages 5 - 7).
Then connect the PoE adapter for USB-C to the cable
and connect it to your LAN cable.
One Kiosk, User Manual & Installation Guide Page of9 11

Installation of the Optional
Scanning Module
Illustrations and texts are examples that vary on the iPad and USB port, other power supplies, or cables.
Step 3.1
Insert the adapter plate into the camera opening. If you
have already inserted the camera cover (step 1.1),
remove it.
Step 3.2
Mount the scanning module over the designated points
on the adapter plate.
Step 3.3
Do the further assembly steps according to steps 1.2 -
1.7 (or 2.2 - 2.6 for PoE).
! Note on 1.4: The holder is turned by 180 degrees and
screwed onto the standpipe. The cable outlet leads to
the left side.
! Note on 1.4: An optimal use of the scan function is
only possible when mounting in landscape format.
This is the only way to create the scan area below the
holder.
One Kiosk, User Manual & Installation Guide Page of10 11

Warranty
Warranty
The One Kiosk comes with a 1 year warranty from purchase date by
the original end customer, unless the device was repaired or replaced
during the warranty period. In this case, the warranty is valid until the
end of the regular two year warranty or six months following the
repair/replacement, whichever comes first.
Warranty Claims and
Verification
Should your One Kiosk not perform as expected, please contact your
dealer and provide the original invoice with serial number as
well as a brief description of your complaint.
The following devices are excluded from the warranty
Devices with damages caused by:
-Acts of nature,
-Misuse, including but not limited to disregarding the user manual and
mounting instructions,
-Inappropriate handling,
-Connection to an incorrect power supply,
-Repairs or attempted repairs by unauthorized persons,
-Use of the device in connection with third party products,
devices on which the serial number of the producer has been changed,
deleted, removed or made illegible.
Apple, iPad and Lightning
are registered trademarks of Apple Inc.
One Kiosk, User Manual & Installation Guide Page of11 11