Vivo Link VLHDBSP1X4V2 User manual

VLHDBSP1X4V2
1x4 HDBaseT Splitter
All Rights Reserved
Version: VLHDBSP1X4V2_2022V1.0
User Manual

1
1x4 HDBaseT Splitter
Preface
Read this user manual carefully before using the product. Pictures shown in this manual
are for reference only. Different models and specifications are subject to real product.
This manual is only for operation instruction, please contact the local distributor for
maintenance assistance. The functions described in this version were updated till
January, 2019. In the constant effort to improve the product, we reserve the right to
make functions or parameters changes without notice or obligation. Please refer to the
dealers for the latest details.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. It has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a commercial
installation.
Operation of this equipment in a residential area is likely to cause interference, in which
case the user at their own expense will be required to take whatever measures may be
necessary to correct the interference.
Any changes or modifications not expressly approved by the manufacture would void
the user’s authority to operate the equipment.

1
1x4 HDBaseT Splitter
SAFETY PRECAUTIONS
To ensure the best performance from the product, please read all instructions carefully
before using the device. Save this manual for further reference.
⚫Unpack the equipment carefully and save the original box and packing material for
possible future shipment.
⚫Follow basic safety precautions to reduce the risk of fire, electrical shock and injury
to persons.
⚫Do not dismantle the housing or modify the module. It may result in electrical shock
or burn.
⚫Using supplies or parts not meeting the products’ specifications may cause damage,
deterioration or malfunction.
⚫Refer all servicing to qualified service personnel.
⚫To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this
product near water.
⚫Do not put any heavy items on the extension cable in case of extrusion.
⚫Do not remove the housing of the device as opening or removing housing may
expose you to dangerous voltage or other hazards.
⚫Install the device in a place with fine ventilation to avoid damage caused by
overheat.
⚫Keep the module away from liquids.
⚫Spillage into the housing may result in fire, electrical shock, or equipment damage. If
an object or liquid falls or spills on to the housing, unplug the module immediately.
⚫Do not twist or pull by force ends of the optical cable. It can cause malfunction.
⚫Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to
the device before cleaning.
⚫Unplug the power cord when left unused for a long period of time.
⚫Information on disposal for scrapped devices: do not burn or mix with general
household waste, please treat them as normal electrical wastes.

1
1x4 HDBaseT Splitter
Elektro- und Elektronikgeräte
Informationen für private Haushalte
Das Elektro- und Elektronikgerätegesetz (ElektroG) enthält eine Vielzahl von
Anforderungen an den Umgang mit Elektro- und Elektronikgeräten. Die wichtigsten sind
hier zusammengestellt.
1. Getrennte Erfassung von Altgeräten
Elektro- und Elektronikgeräte, die zu Abfall geworden sind, werden als Altgeräte
bezeichnet. Besitzer von Altgeräten haben diese einer vom unsortierten Siedlungsabfall
getrennten Erfassung zuzuführen. Altgeräte gehören insbesondere nicht in den
Hausmüll, sondern in spezielle Sammel- und Rückgabesysteme.
2. Batterien und Akkus sowie Lampen
Besitzer von Altgeräten haben Altbatterien und Altakkumulatoren, die nicht vom Altgerät
umschlossen sind, sowie Lampen, die zerstörungsfrei aus dem Altgerät entnommen
werden können, im Regelfall vor der Abgabe an einer Erfassungsstelle vom Altgerät zu
trennen. Dies gilt nicht, soweit Altgeräte einer Vorbereitung zur Wiederverwendung
unter Beteiligung eines öffentlich-rechtlichen Entsorgungsträgers zugeführt werden.
3. Möglichkeiten der Rückgabe von Altgeräten
Besitzer von Altgeräten aus privaten Haushalten können diese bei den Sammelstellen
der öffentlich-rechtlichen Entsorgungsträger oder bei den von Herstellern oder
Vertreibern im Sinne des ElektroG eingerichteten Rücknahmestellen unentgeltlich
abgeben.Rücknahmepflichtig sind Geschäfte mit einer Verkaufsfläche von mindestens
400 m²für Elektro- und Elektronikgeräte sowie diejenigen Lebensmittelgeschäfte mit
einer Gesamtverkaufsfläche von mindestens 800 m², die mehrmals pro Jahr oder
dauerhaft Elektro- und Elektronikgeräte anbieten und auf dem Markt bereitstellen. Dies
gilt auch bei Vertrieb unter Verwendung von Fernkommunikationsmitteln, wenn die
Lager- und Versandflächen für Elektro- und Elektronikgeräte mindestens 400 m²
betragen oder die gesamten Lager- und Versandflächen mindestens 800 m²betragen.
Vertreiber haben die Rücknahme grundsätzlich durch geeignete
Rückgabemöglichkeiten in zumutbarer Entfernung zum jeweiligen Endnutzer zu
gewährleisten. Die Möglichkeit der unentgeltlichen Rückgabe eines Altgerätes besteht

1
1x4 HDBaseT Splitter
bei rücknahmepflichtigen Vertreibern unter anderem dann, wenn ein neues
gleichartiges Gerät, das im Wesentlichen die gleichen Funktionen erfüllt, an einen
Endnutzer abgegeben wird. Wenn ein neues Gerät an einen privaten Haushalt
ausgeliefert wird, kann das gleichartige Altgerät auch dort zur unentgeltlichen Abholung
übergeben werden; dies gilt bei einem Vertrieb unter Verwendung von
Fernkommunikationsmitteln für Geräte der Kategorien 1, 2 oder 4 gemäߧ2 Abs. 1
ElektroG, nämlich „Wärmeüberträger“, „Bildschirmgeräte“ oder „Großgeräte“ (letztere
mit mindestens einer äußeren Abmessung über 50 Zentimeter). Zu einer
entsprechenden Rückgabe-Absicht werden Endnutzer beim Abschluss eines
Kaufvertrages befragt. Außerdem besteht die Möglichkeit der unentgeltlichen Rückgabe
bei Sammelstellen der Vertreiber unabhängig vom Kauf eines neuen Gerätes für solche
Altgeräte, die in keiner äußeren Abmessung größer als 25 Zentimeter sind, und zwar
beschränkt auf drei Altgeräte pro Geräteart.
4. Datenschutz-Hinweis
Altgeräte enthalten häufig sensible personenbezogene Daten. Dies gilt insbesondere für
Geräte der Informations- und Telekommunikationstechnik wie Computer und
Smartphones. Bitte beachten Sie in Ihrem eigenen Interesse, dass für die Löschung der
Daten auf den zu entsorgenden Altgeräten jeder Endnutzer selbst verantwortlich ist.
5. Bedeutung des Symbols „durchgestrichene Mülltonne“
Das auf Elektro- und Elektronikgeräten regelmäßig abgebildete Symbol einer
durchgestrichenen Mülltonne weist darauf hin, dass das jeweilige Gerät am Ende seiner
Lebensdauer getrennt vom unsortierten Siedlungsabfall zu erfassen ist

1x4 HDBaseT Splitter
Table of Contents
1. Product Introduction....................................................................................................7
1.1 Features ............................................................................................................7
1.2 Package List......................................................................................................7
2. Technical Specification................................................................................................8
2.1 HDBaseT Splitter...............................................................................................8
2.2 Video Resolution Down-scaling.......................................................................10
3. Panel Description......................................................................................................11
3.1 Splitter Front Panel..........................................................................................11
3.2 Splitter Rear Panel...........................................................................................11
4. System Connection...................................................................................................13
5. IR Control..................................................................................................................15
5.1 Controlling the Display Device by IR IN...........................................................15
5.2 Controlling the Display Device by IRALL IN....................................................16
5.3 Controlling the Source Device.........................................................................17
6. RS232 Control..........................................................................................................18
7. DIP Switch Operation................................................................................................21
7.1 EDID Management..........................................................................................21
7.2 HDCP Mode.....................................................................................................22
8. Firmware Upgrade....................................................................................................22

1x4 HDBaseT Splitter
7
1. Product Introduction
Thanks for choosing this1x4 HDBaseT Splitter! This device accepts a single HDMI
input and splits it into one HDMI and four HDBaseT outputs. The splitter is designed
with an IR loop out and loop in which are intended to cascade to additional units. It
supports video resolutions up to 4K@60Hz 4:4:4 8bit and all HDMI audio formats. It
can extend 1080p signals on each output to distance up to 229 feet (70 meters) and
4K signals to distance up to 131 feet (40 meters) over a single CATx Ethernet cable. It
supports the Power over HDBaseT (PoC) feature, which allows the HDBaseT
receivers (Sold separately) to be powered from the splitter over the Ethernet cables. It
supports bidirectional IR pass-through and IR, RS232 cascade control.
1.1 Features
⚫Support HDMI 2.0, video resolutions up to 4K@60Hz 4:4:4.
⚫Distribute one UHD/4K HDMI signal to four HDBaseT outputs and one loop HDMI
output.
⚫Supports cascade connection, distribute video signal to multiple video displays.
⚫Maximum transmission distance is up to 40m for 4K, and 70m for 1080p.
⚫Supports video resolution down-scaling, 4K input can be automatically
downgraded to 1080 output.
⚫Supports audio de-embedding.
⚫Each HDBaseT output supports IR pass-through.
⚫Support RS232 and IR cascade control.
⚫Support 24V PoC, the HDBaseT receiver can be powered by HDBaseT splitter.
1.2 Package List
⚫1x VLHDBSP1X4V2 1x4 HDBaseT Splitter
⚫2x Mounting Ears with 4 Screws
⚫4x Plastic Cushions
⚫1x IR Cable (3.5mm to 3.5mm, used
for IR cascade)
⚫4x IR Receivers
⚫1x IR Emitter
⚫1x RS232 Cable (3-pin to 3-pin, used
for RS232 cascade)
⚫1x RS232 Cable (3-pin to DB9)
⚫1x 5-pin terminal block
⚫1x Power Adaptor (24V DC 5A)
⚫1x User Manual
Note: Please contact your distributor immediately if any damage or defect in the
components is found.

1x4 HDBaseT Splitter
8
2. Technical Specification
2.1 HDBaseT Splitter
Video Input
Input
(1) HDMI
Input Connector
(1) Female type A HDMI
HDMI Input Resolution
Up to 4K@60Hz 4:4:4 8bit
Video Output
Output
(1) HDMI, (4) HDBT
Output Connector
(1) Female type A HDMI; (4) RJ45
HDMI Output Resolution
Up to 4K@60Hz 4:4:4
HDBT Output Resolution
Up to 4K@60Hz 4:4:4 (Signal has been compressed.)
SPDIF Audio Output
Audio Output
(1) SPDIF
Audio Output Connector
(1) Toslink
Audio Format
LPCM 2ch, Dolby Digital 2ch, 5.1ch, 7.1ch, Dolby TureHD 7.1ch, DTS
2ch, 5.1ch
Output Level
±0.05dBFS
Frequency Response
20Hz ~20kHz, ±1dB
THD+N
< 0.05%, 20Hz ~20kHz bandwidth, 1kHz sine at 0dBFS level (or max
level)
SNR
> 90dB, 20Hz ~20kHz bandwidth
Crosstalk Isolation
> 70dB, 10kHz sine at 0dBFS level (or max level before clipping)
Noise
-90dB
Stereo Balanced L/R Audio Output
Audio Output
(1) Stereo balanced L/R audio
Audio Output Connector
(1) 5-pin terminal block
Audio Format
PCM
Frequency Response
20Hz ~20kHz, ±1dB
Max output level
2.0Vrms ±0.5dB.
THD+N
< 0.05%, 20Hz ~20kHz bandwidth, 1kHz sine at 0dBFS level (or max
level)
SNR
> 80dB, 20Hz ~20kHz bandwidth
Crosstalk Isolation
> 70 dB, 10kHz sine at 0dBFS level (or max level before clipping)
L-R Level Deviation
< 0.3 dB, 1kHz sine at 0dBFS level (or max level before clipping)
Output Load Capability
1kohm and higher (supports 10x paralleled 10kohm loads)
Noise
- 80dB
Control

1x4 HDBaseT Splitter
9
Control port
(1) EDID, (1) FIRMWARE, (1) ID PRESET, (1) IR ALL IN/LOOP IN,
(1) IR OUT, (4) IR IN, (1) IR LOOP OUT, (1) RS232 IN, (1) RS232 OUT,
Control Connector
(1) 4-pin DIP switch, (1) Micro-USB, (1) DIP switch, (7) 3.5mm mini
jacks, (2) 3-pin terminal blocks
General
HDMI Standard
2.0
HDCP Version
2.2
Transmission Mode
HDBaseT
Transmission Distance
1080p ≤ 229 feet (70 meters), 4K ≤ 131 feet (40 meters)
Operation Temperature
-10 ~ +55℃
Storage Temperature
-25~ +70℃
Relative Humidity
10% ~ 90%
AC Adapter Input Power
100V~240V AC, 50/60Hz
Input Power
24V DC 5A
Power Consumption
47W (Max)
Dimension (W*H*D)
250mm x 44mm x 148mm
Net Weight
1.16kg
Note: SPDIF audio output does not support DTS-HD Master Audio and Dolby TrueHD
format.

1x4 HDBaseT Splitter
10
2.2 Video Resolution Down-scaling
The product supports video resolution down-scaling, the 4K input can be automatically
degraded to 1080p output for compatibility with 1080p display, shown in the below chart.
HDMI Output:
Input
Output
#
Resolution
Refresh
Color Space
Downscale
1080p Specs
1
3840x2160
60
4:4:4
Support
1080p@60Hz 4:4:4
2
3840x2160
30
4:4:4
Support
1080p@30Hz 4:4:4
3
3840x2160
24
4:4:4
Support
1080p@24Hz 4:4:4
4
3840x2160
60
4:2:0
Support
1080p@60Hz 4:4:4
5
3840x2160
60
4:2:2
Support
1080p@60Hz 4:4:4
6
3840x2160
30
4:2:2
Support
1080p@30Hz 4:4:4
7
3840x2160
24
4:2:2
Support
1080p@24Hz 4:4:4
8
3840x2160
60
RGB
Support
1080p@60Hz RGB
9
3840x2160
30
RGB
Support
1080p@30Hz RGB
10
3840x2160
24
RGB
Support
1080p@24Hz RGB
HDBT Output:
Input
Output
#
Resolution
Refresh
Color Space
Downscale
1080p Specs
1
3840x2160
60
4:4:4
Support
1080p@60Hz 4:4:4
2
3840x2160
30
4:4:4
Support
1080p@30Hz 4:4:4
3
3840x2160
24
4:4:4
Support
1080p@24Hz 4:4:4
4
3840x2160
60
4:2:0
Support
1080p@60Hz 4:4:4
5
3840x2160
60
4:2:2
Support
1080p@60Hz 4:4:4
6
3840x2160
30
4:2:2
Not Support
N/A
7
3840x2160
24
4:2:2
Not Support
N/A
8
3840x2160
60
RGB
Support
1080p@60Hz 4:4:4
9
3840x2160
30
RGB
Support
1080p@30Hz RGB
10
3840x2160
24
RGB
Support
1080p@24Hz RGB

1x4 HDBaseT Splitter
11
3. Panel Description
3.1 Splitter Front Panel
1. POWER LED: Illuminates red when power is applied.
2. INPUT LED: Illuminates green when there is HDMI source input.
3. OUTPUT LEDs: The HDMI LED illuminates green when there is HDMI output. The
HDBT 1~3 LEDs illuminate green when there is a valid HDBaseT link between the
splitter and the receiver.
4. 4-pin DIP switch for EDID setting and HDCP mode selection.
5. FIRMWARE: Micro-USB port for firmware upgrade.
3.2 Splitter Rear Panel
1. HDMI INPUT: Connects to HDMI source device.
2. OUTPUTS:
⚫HDMI: Connects to local HDMI display device.
⚫HDBT 1~4: Connect to four HDBaseT receivers.
⚫IR IN: Connect to four IR receivers to control far-end third-party devices by IR.
3. AUDIO OUT:
⚫Toslink audio output for audio de-embedding from HDMI output.
⚫Balanced L/R audio output for audio de-embedding from HDMI output.
FIRMWARE
OUTPUTS
INPUT
HDMI HDBT 1 HDBT 2 HDBT 3 HDBT 4
1 2 3 4
ON
OFF 1
0
123 4 5
ID PRESET DC 24V
OUTPUTS RS232 OUT
Tx RxTx Rx
RS232 INHDMI
INPUT
HDMI
IR OUT
CONTROL
IR IN IR IN IR IN IR IN
HDBT 1 HDBT 2 HDBT 3 HDBT 4 AUDIO OUT
L R
SPDIF
12345

1x4 HDBaseT Splitter
12
4. CONTROL:
⚫IR ALL IN/LOOP IN: Connects to IR receiver to control far-end display device,
or it can be connected to IR LOOP OUT of previous splitter.
⚫IR OUT: Connects to IR emitter to control the local source device by IR.
⚫IR LOOP OUT: Connects to IR ALL IN port of next splitter.
⚫RS232 IN: Connects to control device (e.g. PC) to control the splitter or far-end
third-party devices by RS232, or it can be connected to the RS232 OUT port of
previous splitter.
⚫RS232 OUT: Connects to the RS232 IN port of next splitter.
⚫ID PRESET: Assigns a unique ID to each splitter when cascading multiple
splitters. There are sixteen ID (0~9, A~F) can be set by using a small, flathead
screwdriver. The new ID will take effect after device reboot.
5. DC 24V: DC connector for the power adapter connection.

1x4 HDBaseT Splitter
13
4. System Connection
Receiver
4K TV
Receiver
Receiver
Receiver
IR Emtter
Remote IR Receiver
Blu-Ray
Laptop
Next 1x4 Splitter
Speaker
HDMI:
RS232:
HDBaseT:
IR:
Audio:
ID = 1
ID = 2

1x4 HDBaseT Splitter
14
Cascade Connection:
The splitter supports cascade connection to distribute video signal to multiple video
displays. Use the following connection diagram as a guide for cascading multiple units.
Note that each unit must have a unique ID if using RS232 control.
ID PRES ET DC 2 4V
OUTP UTS RS 232 OUT
Tx RxTx Rx
RS23 2 INHDMI
INPU T
HDMI
IR OUT
CONT ROL
IR IN IR IN IR IN IR IN
HDBT 1 HDBT 2 HDBT 3 HDBT 4 AUDI O OUT
L R
SPDIF
ID PRES ET DC 2 4V
OUTP UTS RS 232 OUT
Tx RxTx Rx
RS23 2 INHDMI
INPU T
HDMI
IR OUT
CONT ROL
IR IN IR IN IR IN IR IN
HDBT 1 HDBT 2 HDBT 3 HDBT 4 AUDI O OUT
L R
SPDIF
Receiver
Tx Rx
LINKHDCP
4K TV
IR Emtter
Receiver
Receiver
Tx Rx
LINKHDCP
4K TV
IR Emtter
Tx Rx
LINKHDCP
4K TV
IR Emtter
Remote IR Receiver
Remote IR Receiver
Remote IR Receiver
Remote IR Receiver
Remote IR Receiver
Blu-Ray
Laptop
HDMI:
RS232:
HDBaseT:
IR:
Next 1x4 Splitter
Receiver
Tx Rx
LINKHDCP
4K TV
IR Emtter

1x4 HDBaseT Splitter
15
5. IR Control
The IR receivers and emitters can be connected to the system to allow for IR control of
remote devices. The bidirectional IR feature provides the two-way control either for the
source or display device(s). Use the following sample connection diagrams to connect
for IR remote control.
5.1 Controlling the Display Device by IR IN
The four IR IN ports of the splitter can receive IR signals from remotes to send to
control displays. Connect four IR receiver to IR IN ports of the splitter, and then
connect four IR emitters to IR OUT ports on HDBaseT receivers.
ID PR ESET DC 24V
OUTPUTS R S232 OUT
Tx RxTx Rx
RS2 32 INHDM I
INPUT
HDMI
IR OU T
CONTROL
IR IN IR IN IR IN IR IN
HDB T 1 HDB T 2 HD BT 3 HDB T 4 AUDIO OUT
L R
SPDIF
Tx Rx
LINKHDCP
Tx Rx
LINKHDCP
4K TV-4
IR
Emitter
Receiver
4K TV-1
IR
Emitter
Receiver
IR Receiver
T -4 Remote V
IR Receiver
T -1 Remote V
1080P 70M
4K 40M
1080P 70M
4K 40M
DVD
HDMI:
IR:
HDBT:
HDMI:
IR:
HDBT:

1x4 HDBaseT Splitter
16
5.2 Controlling the Display Device by IR ALL IN
The IR ALL IN port of the splitter can receive all IR signals from remotes to send to
control displays. Connect an IR receiver to IR ALL IN port of the splitter, and then
connect four IR emitters to IR OUT port on HDBaseT receivers.
IR
Emitter
ID PR ESET DC 24V
OUTPUTS RS2 32 OUT
Tx RxTx Rx
RS2 32 INHDM I
INPUT
HDMI
IR OU T
CONTROL
IR IN IR IN IR IN I R IN
HDB T 1 HDBT 2 HDB T 3 HDBT 4 AUDIO OUT
L R
SPDIF
Tx Rx
LINKHDCP
Tx Rx
LINKHDCP
4K TV-4
IR
Emitter
Receiver
4K TV-1
Receiver
IR Receiver
T -1 2 3 4 Remote V ///
1080P 70M
4K 40M
1080P 70M
4K 40M
DVD
HDMI:
IR:
HDBT:

1x4 HDBaseT Splitter
17
5.3 Controlling the Source Device
The IR OUT port of the splitter can send all IR signals to control source device.
Connect four IR receivers to IR IN ports on HDBaseT receivers, and then connect an
IR emitter to IR OUT port of the splitter.
Tx Rx
LINKHDCP
Tx Rx
LINKHDCP
ID PRESET DC 24V
OUTPUTS RS232 OUT
Tx RxTx Rx
RS232 INHDMI
INPUT
HDMI
IR OUT
CONTROL
IR IN IR IN IR IN IR IN
HDBT 1 HDBT 2 HDBT 3 HDBT 4 AUDIO OUT
L R
SPDIF
4K TV-4
Receiver
4K TV-1
Receiver
IR
Receiver
DVD Remote
IR
Receiver
DVD Remote
1080P 70M
4K 40M
1080P 70M
4K 40M
DVD
IR
Emitter
HDMI:
IR:
HDBT:

1x4 HDBaseT Splitter
18
6. RS232 Control
The splitter and compatible receivers features RS232 ports to transmit RS232 signals
from computer to control far-end third-party devices by using 3-pin to DB9 cable and a
RS232 control software, such as docklight. After installing the RS232 control software,
please set the parameters of COM number, bound rate, data bit, stop bit and the parity
bit correctly. Compatible receivers must be able to communicate at 2400, 4800, 9600,
19200, 38400, 57600, or 115200 baud. The splitter requires the following
communication protocol parameters:
Baud rate: 9600 (default)
Data bit: 8
Stop bit: 1
Parity bit: none
RS232 Commands
The end mark of below commands is “<CR><LF>”.
Command
Function
Command Example and
Feedback
#param1_GET_FIRM
WARE_VERSION
Get the firmware version.
param1=0~15. The splitter ID 0~9, A~F.
param1=ALL. All splitters.
#5_GET_FIRMWARE_VER
SION
@5_V1.0.0
#param1_FACTORY_
RESET
Restore to factory Default setting.
param1=0~15. The splitter ID 0~9, A~F.
param1=ALL. All splitters.
#5_FACTORY_RESET
@5_FACTORY_RESET
#param1_SET_RS232
_BAUD param2
Set the baud rate of splitter.
param1=0~15. The splitter ID 0~9, A~F.
param1=ALL. All splitters.param1=ALL.
param2=0~4. Baud rate.
0=9600
1=19200
2=38400
3=57600
4=115200
#5_SET_RS232_BAUD 0
@5_RS232_BAUD 9600
#param1_GET_RS232
_BAUD
Get the baud rate of splitter.
param1=0~15. The splitter ID 0~9, A~F.
param1=ALL. All splitters.
#5_GET_RS232_BAUD
@5_RS232_BAUD 9600
#param1_GET_STATE
Get system status.
#5_GET_STATE

1x4 HDBaseT Splitter
19
Command
Function
Command Example and
Feedback
param1=0~15. The splitter ID 0~9, A~F.
param1=ALL. All splitters.
@ID:5
@5_V1.x.x
@5_RS232_BAUD xxx
@5_HDBT_PoC_x_ON/OF
F
@5_SPDIF_ON/OFF
@5_I2S_ON/OFF
@5_EDID:xxx
@5_HDCP:xxx
#param1_GET_DIP
Get EDID DIP switch status.
param1=0~15. The splitter ID 0~9, A~F.
param1=ALL. All splitters.
#5_GET_DIP
@5_EDID:xxx
@5_HDCP:xxx
#param1_SET_HDBT_
PoC param2 param3
Turn on/off PoC of HDBT output.
param1=0~15. The splitter ID 0~9, A~F.
param1=ALL. All splitters.
param2=1~4. HDBT output 1~4.
param2=0. All HDBT outputs.
Param3=ON/OFF. PoC ON/OFF.
#5_SET_HDBT_PoC 1 ON
@5_HDBT_PoC_1_ON
#param1_GET_HDBT_
PoC
Get PoC on-off status.
#5_GET_HDBT_PoC
@5_HDBT_PoC_1_ON
#param1_SET_SPDIF
param2
Turn on/off SPDIF audio output.
param1=0~15. The splitter ID 0~9, A~F.
param1=ALL. All splitters.
param2=ON/OFF.
#5_SET_SPDIF ON
@5_SPDIF_ON
#param1_GET_SPDIF
Get the on-off status of SPDIF audio output.
param1=0~15. The splitter ID 0~9, A~F.
param1=ALL. All splitters.
#5_GET_SPDIF
@5_SPDIF_ON
#param1_SET_I2S
param2
Turn on/off balanced audio (L/R) output.
param1=0~15. The splitter ID 0~9, A~F.
param1=ALL. All splitters.
param2=ON/OFF.
#5_SET_I2S ON
@5_I2S_ON
#param1_GET_I2S
Get the on-off status of balanced audio (L/R)
output.
param1=0~15. The splitter ID 0~9, A~F.
param1=ALL. All splitters.
#5_GET_I2S
@5_I2S_ON

1x4 HDBaseT Splitter
20
The following commands do not require end mark.
Command
Function
Command Example and
Feedback
#param1_SEND_A_pa
ram2_param3:param4
Send ASCII command to control the far-end
third-party device which is connected to the
RS232 port of HDBaseT receiver.
param1=0~15. The splitter ID 0~9, A~F.
param1=ALL. All splitters.
param2=1~4. HDBT output 1~4.
param2=0. All HDBT outputs.
param3=0~4. Baud rate.
0=9600
1=19200,
2=38400
3=57600
4=115200
param4=ASCII command.
#5_SET_A_1_0:ABC12345
67
…
#param1_SET_H_para
m2_param3:param4
Send HEX command to control the far-end
third-party device which is connected to the
RS232 port of HDBaseT receiver.
param1=0~15. The splitter ID 0~9, A~F.
param1=ALL. All splitters.
param2=1~4. HDBT output 1~4.
param2=0. All HDBT outputs.
param3=0~4. Baud rate.
0=9600
1=19200,
2=38400
3=57600
4=115200
param4=HEX command.
#5_SET_H_1_0:11 22 33 44
55
…