Vivo DESK-SKIRT-30P User manual

Black Clamp-on 30”
Cable Management
Desk Organizer
Instruction Manual
SKU: DESK-SKIRT-30P
Assembly Video & Product Info
www.vivo-us.com/products/desk-skirt-30p

2
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please contact our product support team at 309-278-5303 or [e-mail] for further assistance.
Check carefully to make sure there are no missing or defective parts. Improper installation may cause
damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
CAUTION!
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
We’re Here for You
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
Chat Us:
www.vivo-us.com
Give us a Call:
309-278-5303
Email Us:
[email protected]om AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
6.6lbs
(3kg)

3
Package Contents
Included Hardware
Tools Needed:
B(x2)
Side Bar
C(x2)
Mounting Clip
A (x1)
Panel
D (x2)
T Joiner
DrillPhillips
Screwdriver
E (x2)
Clamp
S-B (x2)
ST4.8x19 Screw
Pencil
F (x4)
Upper/Lower
Bar
G (x1)
Middle Bar
H (x4)
Joiner
S-A (x2)
M4x6mm Screw

4
ASSEMBLY STEPS
STEP 1
STEP 2
NOTE: Ensure all bars and joiners are fully pressed in for a secure fit.
Open the flap and straps of the Panel (A) and insert the frame, making sure the frame is fully
inserted and the material is tightly stretched around it.
Snug Fit:
Fabric on panel has a tight fit around the frame and may need to be stretched
before inserting the frame.
Connect the centers of the T Joiners (D) to the ends of the Middle Bar (G). Connect the Upper/Lower
Bars (F) to the sides of the T Joiners (D), then connect the Joiners (H) and Side Bars (B) to the sides
to complete the frame assembly. Lighty tap each joint against a hard surface to ensure all bars and
joiners are full pressed in.
D
G
H
F
A

5
STEP 3
STEP 4
Fasten the straps on Panel (A) to around the assembled frame to secure.
A
C
A
Place Mounting Clips (C) in the center of each exposed portion of Upper/Lower Bars (F). Make sure
the wire management flap on Panel (A) is facing upward.
NOTE: To screw mount under your desktop instead of
clamping, please skip to Step 4-Option 2 on page 6.
F

6
STEP 5
STEP 6
E
E1 E2
For thinner desktops (<1.5”/40mm), adjust Clamp (E) by disassembling and separating Upper Clamp
(E1) from Lower Clamp (E2). Flip Lower Clamp (E2) and reassemble using a Phillips screwdriver.
Secure Mounting Clips (C) to Clamps (E) in one of two mounting locations using M4x6mm Screws
(S-A).
S-A
C
C
EE
DESKTOPS 15-50MM/0.6-2” THICK DESKTOPS 10-40MM/0.39-1.5” THICK
S-A

7
STEP 7
Mount the assembled panel to the desktop and tighten Clamps (E) to secure the assembly in place.
Route and organize the cables and secure them using
the flap on the panel (A).
E
A
STEP 8

8
Screw Mounting
Center the assembled panel under the desktop.
E
Screw Mounting:
Place Mounting Clips (C) in the center of each exposed portion of Upper/Lower Bars (F).
NOTE: Make sure the wire management flap on Panel (A) is facing the inside of
the desktop.
A
C
STEP 4 (Option 2)
STEP 5 (Option 2)

9
Screw Mounting
Route and organize the cables and secure them using the flap on Panel (A).
A
Screw Mounting
Mark the locations of Mounting Clips (C) using a pencil. Drill pilot holes using a 1/8” (3mm) bit and
mount the assembled panel to the underside of the desk using ST4.8x21mm Screws (S-B) as shown.
NOTE: Desktop must be at least 1” thick to prevent screws from poking out through the top and damaging the surface.
C
S-B
STEP 6 (Option 2)
STEP 7 (Option 2)

10
[PAGE LEFT INTENTIONALLY BLANK]

11
[PAGE LEFT INTENTIONALLY BLANK]

LAST UPDATED: 01/08/24
REV2
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
Monday-Friday from 7:00am-7:00pm CST
Need Help? Get In Touch
FOR MORE GREAT VIVO PRODUCTS,
CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM
VIVO-us @vivo_us