Vivo MOUNT-POLE05L User manual

Pole Mount Pneumatic Arm Laptop Holder
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-pole05l
SKU: MOUNT-POLE05L
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
A (x1)
Arm
B(x1)
Bracket
C (x1)
Laptop Tray
E(x2)
Clip
M-B (x4)
M5x12mm Screw
M-C (x4)
M5 Washer
D (x2)
Laptop Tray
Arm
S-A (x2)
M8x50mm Screws
S-B (x2)
M8x65mm Screw
9.9 lbs
(4.5 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
T-A (x1)
4mm Allen Wrench
T-B (x1)
5mm Allen Wrench
S-C (x2)
M8 Nut
S-D (x4)
M4x8mm Screw
M-A (x4)
M4x12mm Screw

3
ASSEMBLY STEPS
STEP 1
While holding Arm (A) closed, cut the shipping tie and gently open Arm (A).
STEP 2 (Option A)
28-45mm Pole Diameter:
For poles with a diameter of 28-45mm, assemble Arm (A) to the pole using Bracket (B) and M8x50mm
Screws (S-A) with M8 Nuts (S-C). Tighten screws using 5mm Allen Wrench (T-B).
A
A
B
S-A
S-C
T-B

4
46-60mm Pole Diameter:
For poles with a diameter of 46-60mm, assemble Arm (A) to the pole using Bracket (B) and M8x65mm
Screws (S-B) with M8 Nuts (S-C). Tighten screws using 5mm Allen Wrench (T-B).
STEP 2 (Option B)
Install Laptop Tray Arms (D) to Laptop Tray (C) using Clips (E).
STEP 3
A
B
S-B
S-C
T-B
D
C
E

5
STEP 4
Insert M4x8mm Screws (S-D) into the top two holes of Laptop Tray (C) using the Phillips end of 4mm
Allen Wrench (T-A), leaving atleast 3mm of threads exposed. Slide installed M4x8mm Screws (S-D) into
the slots in the VESA plate on Arm (A). Install remaining M4x8mm Screws (S-D) into the lower holes of
Laptop Tray (C).
S-D
C
T-A
S-D
Slot
A
Lower Hole
S-D T-A
C

6
STEP 6
Flip the stoppers on Laptop Tray (C) to prevent the laptop from sliding down. Unlock the latches on the
underside of Laptop Tray Arms (D) to adjust the arms to t your laptop. Place the laptop on Laptop Tray
(C), and once adjusted, lock Laptop Tray Arms (D) to secure it in place.
Stopper
C
D
STEP 5
Adjust the tension in Arm (A) using 5mm Allen Wrench (T-B).
A
T-B

7
STEP 7
Remove the screws from the cable management covers on the underside of Arm (A) using the Phillips
end of 4mm Allen Wrench (T-A). Route cables and reassemble the cable managment covers.
STEP 8
Adjust the tilt of Arm (A) using 5mm Allen Wrench (T-B).
A
T-A
A
T-B

LAST UPDATED: 08/04/2022
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303