Vivo BEE-V003E User manual

Electric Three Frame Stainless Steel Honey Extractor
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/bee-v003e
SKU: BEE-V003E
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about
the safety of the installation, please call a qualied technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual and do not
exceed weight capacity. We cannot be liable for damage or injury caused by
improper mounting, incorrect assembly or inappropriate use.
WARNING: IMPORTANT SAFETY INFORMATION
READ AND FOLLOW ALL SAFETY REQUIREMENTS
PREPARATION
1. Aer carefully removing the machine from the packing carton, remove
all protective lm and clean the honey extractor thoroughly with mild
soap and water BEFORE rst use.
2. The honey extractor should be placed on a dry, at stable surface.
KEEP THIS MANUAL IN A SAFE AND DRY PLACE FOR FUTURE REFERENCE
CAUTION: SHARP EDGES
PACKAGE CONTENTS
A (x1)
Drum
B (x3)
Upper Leg
C (x3)
Lower Leg
D (x2)
Lid
E (x1)
Honey Gate
S-A (x4)
M8x25 Hex
Head Screw
S-B (x4)
M8x20 Hex
Head Screw
S-C (x4)
M8x16 Hex
Head Screw
S-D (x10)
M8 Lock
Washer
S-F (x6)
M8 Plastic
Knob
S-G (x3)
Concrete
Anchor
NOTE: Not all hardware will be used.
S-E (x10)
M8 Washer
S-H (x12)
M4x10 Screw
S-I (x12)
M4 Nut
TOOLS NEEDED
Phillips
Screwdriver

3
STEP 1
Assemble Upper Legs (B) and Lower Legs (C) in one of the two height settings
using M8x16 Hex Head Screws (S-C) M8 Washers (S-E) and M8 Lock Washers (S-
D).
ASSEMBLY STEPS
STEP 2
Mount leg assemblies to Drum (A) using M8x25 Hex Head Screws (S-A) and M8x20
Hex Head Screws (S-B) with M8 Washers (S-E), M8 Lock Washers (S-D) and M8
Plastic Knobs (S-F).
B
C
S-C
S-D
S-B
S-E
S-D
S-F
S-E
S-A
S-E
S-D
S-F

4
STEP 3
Carefully cut the zipties securing the basket to the upper crossbar in Drum (A).
Remove the nuts from the top of the crossbar and carefully remove the crossbar
and basket from Drum (A).
STEP 4
Install Honey Gate (E) in Drum (A) and reinstall the basket and crossbar to Drum
(A).
A
E
A
Inside Drum

5
STEP 5
STEP 6 (Optional)
For added security, Concrete Anchors (S-G) can be use to secure the extractor to
the oor.
S-G
D
S-H
S-I
A
Line up holes in Lids (D) with the hinges in the crossbar of Drum (A) and secure
using M4x10 Screws (S-H) and M4 Nuts (S-I).
NOTE: Lids (D) must be installed properly and in the down position to engage the
safety switches and allow the motor to turn on. Each lid has a built in safety latch
that will cut power the moment it is opened.

6
Once the frames have been emptied on one side, remove the
frames, turn the frames around, and place them back in the
extractor. Repeat step 2, then remove the frames from the
extractor.
STEP 4
With the drain positioned over a bucket or other container, open
the honey gate to begin draining honey. Tip the extractor forward
to drain as much honey as possible.
STEP 5
OPERATING INSTRUCTIONS
With the control dial set to “0” and power switch set to o (O),
plug the power cord into a standard AC wall outlet.
Place honey frames in extractor basket. Load three sides to keep
extractor balanced as this will reduce any possible shaking.
Close both lids to engage safety switches. Flip the power switch
to the on (I) position, and turn the dial until the basket is spinning
at the desired speed. The front lid has a built in safety switch that
will cut power the moment it is opened, and power will not be
restored until lid is closed. Turn the dial back to “0” when frames
have been emptied and remove the frames from the extractor.
DISASSEMBLY
To disassemble the extractor, remove the four cap nuts on the top of the extractor
(two on each side), then pull the top brace up and o. The basket can then be lied
out.
A steel ball bearing rests below the basket sha to improve rotation. Set this aside in
a safe place (such as a cup) so it does not roll away and become lost.
WARNING: KEEP HANDS CLEAR OF MOVING
PARTS TO REDUCE RISK OF INJURY

7
WARRANTY
We oer a ONE YEAR warranty for this product. If you have any problems with the
machine, please contact us directly. We have a 30 Day Return Policy.
CARE & MAINTENANCE
QUICK CLEANING
Option 1: Rinse extractor out with cold water from a hose. If available, a pressure
washer is very eective. Empty excess water to prevent possible surface rust.
Option 2: Place open extractor next to hive. Bees will clean it out and use the
materials.
IN-DEPTH CLEANING
Disassemble extractor (see Disassembly instructions). Using mild dish soap and
warm water, scrub drum and basket clean. Completely rinse the parts and dry with a
so cloth. Reassemble the extractor when dry.
CARE
• When not in use, store the extractor in a dry place. Although stainless steel
is highly resistant to rust and corrosion, light surface rust can form in wet
conditions.
• If surface rust forms, clean with a light abrasive to remove rust.
• If the extractor begins making squeaking noises, lightly lubricate all bearings
with a food safe grease or oil. Wipe away any excess.
• If the roller bearing in the crank sha support block does not turn freely,
lubricate with a light grease (such as white lithium) or oil.
• The gearbox is permanently sealed and requires no maintenance.

LAST UPDATED: 09/07/2021
REV2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oce hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oce hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oce hrs): 5M 4S
309-278-5303