Vixen Horns VXH1264YBX2 User manual

VXH1264YBX2
INSTALLATION GUIDE
PAGE 1 of 3
BEFORE BEGINNING YOUR INSTALLATION
Read through the whole instruction guide before getting started with the installation. Professional installation is
recommended for this product.
CONTENTS
Single Trumpet Horn (Black) x 2
Built-in Weather Cover with Orange Light x 2
12V/24V Solenoid with Compression Fitting x 2
3/8” OD Air Line x 2
Mounting Hardware
SAFETY INSTRUCTIONS
Avoid dismantling this horn’s electrical elements.
Avoid touching compressor components with your bare hands immediately after or during use.
Avoid setting up any parts of the horn where there is a risk of falling off or risk of coming in contact with water.
Avoid reaching out to touch or pick up any fallen or water submerged parts.
Set the horn up for use only in areas with adequate ventilation.
Avoid sounding the air horn when in close range to your ear(s) or the ear(s) of others.
Make sure your battery ground is detached before getting your installation started.
Employ equipment for eye protection during drill operations.
Ensure that your air system has no pressure before starting the installation.
The specific voltage requirement for this horn is 12 or 24 volt DC, therefore installation must be done to a DC
power source of 12 or 24 volts.
MOUNTING
Identify a suitable area for mounting, preferably an unobstructed sheet-metal surface like the frame or body of
the vehicle so as to provide a firm platform which will help protect the horn from damage due to excessive
shaking. Do not attach the horn to any plastic or other flexible material.
Using the back bracket as a guide estimate and mark the positions for the holes, then perforate to size using
a drill.
Move the support bracket towards the trumpet's opening until is tight, then mark the hole and drill.
Use the provided mounting hardware to fasten the horn.

VXH1264YBX2
INSTALLATION GUIDE
PAGE 2 of 3
AIR LINE INSTALLATION
On one side of the included 3/8” OD air line, attach the compression nut and force the air line upon the male
inlet fitting which is found on the electric solenoid valve.
Pass the brass nut through the inlet fitting and fasten.
Take the air line’s other side and place the compression nut of the air tank fitting on it. Force the air line onto
the male fitting of the tank and then fasten the compression nut. WARNING: Avoid tying the brass nut too
tight.
Repeat the steps above to connect the second solenoid to the air supply.
ELECTRICAL CONNECTIONS
Join one wire from one solenoid with one wire from the second solenoid, this will be the positive lead and
must be connected to the positive (+) terminal of the battery or alternator. WARNING: We highly recommend
that you use a 20A fuse (not provided) to assure that the circuit remains safe and will not be damaged by
excess current.
Join the remaining wire of one of the solenoids with the remaining wire of the second solenoid, this will be
your negative lead and must be connected to one of the terminals on the horn button.
Ground the other terminal on the horn button by wiring it to bare metal.

VXH1264YBX2
INSTALLATION GUIDE
PAGE 3 of 3
ELECTRICAL CONNECTIONS (LIGHT)
OPTION 1: Additional Brake Light (Will turn on only when the vehicle's brake is engaged)
Connect the red wire to any wire that powers the vehicle’s brake light.
Connect the black wire to ground by wiring it to bare metal.
OPTION 2: Running Light (Will turn on when vehicle’s running lights are switched to on)
Connect the red wire to a wire that powers vehicle’s running light.
Connect the black wire to ground by wiring it to bare metal.
OPTION 2: Horn Activated (Turns on when the horn button is press)
Connect the red wire to the Solenoid's wire that leads to the power source.
Connect the black wire to the Solenoid's wire that leads to the horn switch.
WARNING: We highly recommend that you use a 10A fuse (not provided) on the positive wire to assure that the
circuit remains safe and will not be damaged by excess current.