VL Audio WS-64 User manual

WS-64
WWW.VL.CO.TH
USER MANAUL
PASSIVE FULL-RANGE SPEAKER

1USER MANAUL
DESCRIPTIONS
Thank you for purchasing a WS-64 Wall Speaker.This
user manual will provide you with useful and important
information about your equipment. Please devote some
time reading it and keep it at hand for future reference.
ATTENTION! Because of the continuous evolution of
techniques and standards,WS-64 reserves the right to
change the specifications of its products without warning.
For the most updated version of this manual and general
information about this and other products, please visit
our website www.vl.co.th
OVERVIEW
The WS-64 Wall Speaker delivers a rich and full sound
experience through advanced acoustic design, ideal to
use in homes, gyms, office areas, schools, restaurants
and more.
1. Tweeter : High Quality Tweeter
2. Grip Handles : Stylish grip handles hold the speakerin place
3. Woofer : Polypropylene Woofer
4. Grille : Sound transparent grille
5. U-Bracket : Easy to install 180°swivel mounting bracket
Distance Between Mounting Holes: 190mm
6. Enclosure : High-grade rugged polypropylene enclosure
PACKAGING CONTENTS
• 2 x VL AUDIO WS-64
• 2 x U-BRACKET • USER MANAUL
INTRODUCTION
2
6
3
4
5
1

2USER MANAUL
LOW IMPEDANCE
The selector switch is used to determine which mode of operation and/or the transformer power tap. When 8Ω mode
is selected be sure to follow the amplifier’s specifications in relation to the minimum allowed impedance. Most amplifiers
allow for a minimum 4Ωimpedance which corresponds to two WS-64 speakers connected in parallel.
100V DISTRIBUTED LINES
The WS-64 comes standard with a transformer for 100V distributed lines, to use your speaker in the 100V distributed line
mode, use the selector to configure the desired power tap (5W, 10W, 20W, 40W) on WS-64
100V LINE INSTALL REQUIREMENTS
100V POWER AMPLIFIER REQUIREMENTS
Make sure you have a powerful enough amplifier for your setup of WS-64 loudspeakers. It must have at least the total
sum of power values chosen on your WS-64 as power tap. Applying the 20% headroom rule, in this case, is the ideal scenario.
Considering the example above, you will need at least (20+20+10+5) x 1.2 = 66W of amplifier power.
CONNECTIONS
AMPLIFIER
100V AMPLIFIER

3USER MANAUL
INSTALLATION
INSTALLATION INSTRUCTIONS
1. Disassemble the U-bracket from the WS-64 by unscrewing
both knob grips (A) and pushing the bracket outwards (B).
2. Using the U-bracket and a pencil, mark the hole spots
for drilling in the desired position. Keep in mind the U-bracket
only allows the WS-64 to rotate. Position in a way that allows
you to steer the WS-64 later for the desired coverage.
3. Mount the U-bracket on the wall using the correct screws
and anchors for the surface in question (not included).
4. Reassemble the WS-64 with the U bracket reversing
the process done on step 1. Do not completely tight the
knob grips.
5. Select the power taps (8Ωor 100V), connect the cables
on the speaker, aim it to the desired location and tight the
knob grips.
A
B
B
A

4USER MANAUL
TECHNICAL SPECIFICATIONS
PRODUCT TYPE 2-WAY PASSIVE SPEAKER (8Ω100V)
FREQUENCY RESPONSE 70Hz - 20kHz
NOMINAL COVERAGE 80°H x 90°V
RMS POWER 40W
PROGRAM POWER 80W (8Ω)
NOMINAL IMPEDANCE 8Ω
SENSITIVITY (1W, 1m) 88dB
MAX SPL (CAL.) 104dB
TRAN. TAP 100V 10W, 20W, 40W
TRAN. TAP 70V 5W, 10W, 20W
LF DRIVER 6” POLYPROPYLENE CONE WOOFER
HF DRIVER 1.5” SILK DOME TWEETER
INPUT CONNECTORS BINDING POSTS
CABINET MATERIAL HIGH-GRADE RUGGED POLYPROPYLENE
HEIGHT 195mm
WIDTH 216mm
DEPTH 300mm
WEIGHT 3.36kg(7.4lb)
SPECIFICATIONS
SIZE
HEIGHT 320mm
WIDTH 425mm
DEPTH 230mm
WEIGHT 6.5kg(14.33lb)
SHIPPING INFORMATION