VL Audio WS-64 B User manual

WS-64 B/W
2-WAY WALL MOUNTED SPEAKER
USER MANAUL
WWW.VL.CO.TH

1USER MANAUL
INTRODUCTION
DESCRIPTIONS
Thank you for purchasing a WS-64 Wall Mounted Speaker. This
user manual will provide you with useful and important information
about your equipment. Please devote some time reading it and keep
it at hand for future reference.
ATTENTION! Because of the continuous evolution of techniques
and standards,WS-64 reserves the right to change the specifications
of its products without warning. For the most updated version of
this manual and general information about this and other products,
please visit our website www.vl.co.th
OVERVIEW
The WS-64 Wall Speaker delivers a rich and full sound experience
through advanced acoustic design, ideal to use in homes, gyms, office
areas, schools, restaurants and more.
PACKAGING CONTENTS
FEATURE
• 70Hz - 20kHz Frequency response(-6db)
• 40W RMS Power
• 88dB Sensitivity
• 104dB Maximum SPL
1. Tweeter :
High Quality Tweeter
2. Grip Handles :
Stylish grip handles hold the speakerin place
3. Woofer :
Polypropylene Woofer
4. Grille :
Sound transparent grille
5. U-Bracket :
Easy to install 180° swivel mounting bracket
Distance Between Mounting Holes: 190mm
6. Enclosure :
High-grade rugged polypropylene enclosure
• 2 x VL AUDIO WS-64
• 2 x U-BRACKET
• USER MANAUL
2
1
4
36
5

2USER MANAUL
CONNECTIONS
1
2
3
Off
Low-z
LOW IMPEDANCE
The selector switch is used to determine which mode of operation and/or the transformer power tap. When 8Ω mode is selected
be sure to follow the amplifier’s specifications in relation to the minimum allowed impedance. Most amplifiers allow for a minimum
4Ω impedance which corresponds to two WS-64 speakers connected in parallel.
100V DISTRIBUTED LINES
The WS-64 comes standard with a transformer for 100V distributed lines, to use your speaker in the 100V distributed line mode,
use the selector to configure the desired power tap (10W, 20W, 40W) on WS-64
100V LINE INSTALL REQUIREMENTS
100V POWER AMPLIFIER REQUIREMENTS
Make sure you have a powerful enough amplifier for your setup of WS-64
loudspeakers. It must have at least the total sum of power values chosen on your WS-64 as power tap. Applying the 20% headroom
rule, in this case, is the ideal scenario. Considering the example above, you will need at least (20+20+10+10) x 1.2 = 72W of amplifier
power.
AMPLIFIER
100V AMPLIFIER

3USER MANAUL
INSTALLATION
INSTALLATION INSTRUCTIONS
Disassemble the U-bracket from the WS-64 by unscrewing both
knob grips (A) and pushing the bracket outwards (B).
Using the U-bracket and a pencil, mark the hole spots for drilling
in the desired position. Keep in mind the U-bracket only allows the
WS-64 to rotate. Position in a way that allows you to steer the WS-64
later for the desired coverage.
Reassemble the WS-64 with the U bracket reversing the process
done on step 1. Do not completely tight the knob grips.
1.
2.
Mount the U-bracket on the wall using the correct screws and
anchors for the surface in question (not included).
3.
4.
Select the power taps (8Ω or 100V), connect the cables on the
speaker, aim it to the desired location and tight the knob grips.
5.
A
B
B
A

4USER MANAUL
SPECIFICATIONS
TECHNICAL SPECIFICATION
WS-64 B/W DIMENSIONS
195mm
216mm
300mm
Product type
Frequency response (-6dB)
2-Way passive speaker (8Ω/100V)
70Hz - 20kHz
Nominal coverage
RMS Power
Program power
Nominal impedance
Sensitivity @1w/1m
Maximum SPL calculated
Transformer taps 100V
Transformer taps 70V
LF Driver
HF Driver
80°H x 90°V
40W
80W(8Ω)
8Ω
88dB
104dB
10W, 20W, 40W
5W, 10W, 20W
6” polypropylene cone woofer
1.5” Silk dome tweeter
TRANSDUCER
Input connector Binding posts
INPUT/OUTPUT SECTION
Cabinet/Case material High-grade rugged polypropylene
PHYSICAL SPECIFICATIONS
Height
Width
Depth
Weight
195mm
216mm
300mm
1.26kg
SIZE
Package height
Package width
Package depth
Package weight
230mm
425mm
230mm
6.5kg
SHIPPING INFORMATIONS