Opus One C 0870 User manual

Operating Instructions
165mm 2-Way Round Wi-Fi
Ceiling Speaker Pair
C 0870
• In-built wi (802.11b/g/n) 2.4GHz with smartphone, tablet or PC control.
• In-built 2 x 30W RMS amplier.
• Includes active [Master] speaker and passive [Slave] speaker units - 60W RMS total.
• High performance woven glass bre woofer and titanium dome tweeter.
• Supports multi-room/zone installations.
• In-app content, zone and output level control [Smartsonix].
• Includes 24V d.c. 2.5A power supply.
Features

C 0870 165mm 2 Way Round WiFi Ceiling Speaker Pair
C 0870 165mm 2 Way Round WiFi Ceiling Speaker Pair
Specications
Inside the Package
Experience wireless music streaming throughout your home with these high-performance ‘Woven Glass
Fibre’ cone speakers. They connect to your home’s wireless router and allow you to stream music directly
from your Wi-Fi enabled devices. Playback can be via stored music, podcasts, Spotify or other music
streaming services. The ‘Smartsonix’ app is available on iOS or Android. You can have up to 10 speaker
sets spread across different rooms in your premises (zones), all being controlled through the ‘Smartsonix’
application’s zone management features. Speakers are also compatible with Apple Airplay, thereby
permitting easy audio streaming directly from a huge array of iOS and Mac app store applications.
Introduction
Speaker Active Speaker Passive Speaker
Woofer 165mm (6.5”) Woven Glass Fibre
cone
165mm (6.5”) Woven Glass Fibre
cone
Tweeter 19mm (0.75”) Titanium dome 19mm (0.75”) Titanium dome
Frequency response 65Hz-20kHz 60Hz-20kHz
Sensitivity (1w/1m) 90dB 90dB
Impedance (Nominal) 8 ohms 8 ohms
RMS Power 30W 30W
Treble attenuation +3dB/-3dB +3dB/-3dB
Dimensions (mm) Ø234 x 100mm Ø234 x 100mm
Amplier
Type Class ‘D’ (digital) /
Rated Power 2x 30W RMS per channel /
Power Input 24V d.c. 2.5A (Adapter included) /
Built-in WiFi Hotspot
Wireless network compatibility 802.11b/g/n 2.4GHz /
Supported audio format MP3/WMA/AAC/ACC/ACC+/ALAC/
APE/WAV
/
Wireless Range 80m /

C 0870 165mm 2 Way Round WiFi Ceiling Speaker Pair
WiFi Speaker Installation
Step 1: Use the enclosed template to mark out the cut out,
then simply cut along the line. This is the only cut you will
need to make.
Cutout Diameter: Ø210mm Installation Depth: >102mm
± 2mm Tolerance
Step 2: Mount the DC adaptor in a suitable place in your
wall or ceiling. Leave the plug end and jack end dangling
through the ceiling hole. The adapter must be able to plug
into a mains power supply. Connect the DC adaptor jack to
the Wi-Fi speaker.
Equipment you will need:
Besides the cut-out template that is included in the box, you must have a ladder and ideally the
equipment shown below to guarantee a safe and efcient installation.
Step 3: Mount the speaker into the ceiling and tighten all
the clamp screws with a Philips screwdriver. The location
should suit the room you have identied in the controller
APP.
Step 4: As several magnets are on the speaker frame,
attach the grill to the rim of the speaker directly.
Ensure the grill is attached to the speaker securely to keep
the grill from falling. Plug in the DC adaptor to the power
supply.

C 0870 165mm 2 Way Round WiFi Ceiling Speaker PairC 0870 165mm 2 Way Round WiFi Ceiling Speaker Pair
Speaker Overview
1. Woofer
2. Environmental Equalizer (±3dB)
• Adjust the switch to optimize the sound.
3. Tweeter
4. LED Indicator
LED Condition Status Meaning
Red rapid ash Standby mode.
Red slow ash Unit is starting up.
Red solid Unit is ON, but not connected to network.
Blue slow ash Connecting to network.
Blue solid Unit is on and connected to network.
Green solid Unit is playing from Wi- source.
Purple solid Unit is playing from Aux input.
Alternate Red, Green and
Blue ashing
Performing factory reset or software
upgrade.
Alternate Red and Blue
flashing
Amplifier fault.
Purple flashing Software fault.
5. WPS
• Short-press: enter the setup mode
• Long-press: restore the device to original default settings
6. Volume Limiter
• Limiter Enabled (50%): The volume will be limited to the max.
output 15W@8Ω
• Limiter Disable (100%): The volume can be adjusted to the
max. output 30W@8Ω
7. Stereo/Mono Switch
• Switch to the “stereo” position when a passive speaker is
attached. If not, keep in “mono” position
8. RCA Jack
9. RJ45 Port
• Ethernet port to connect data cable direct to router.
10. Power Input (DC 24V/2.5A)
11. Gold Plated Terminals

C 0870 165mm 2 Way Round WiFi Ceiling Speaker Pair
Wi-Fi speaker setup:
Method 1 – App connection (iOS & Android devices)
Step 1: Installing Controller APP
• Search the Google play (Android) or App Store (iOS) to download the controller app called ‘Smartsonix’
Step 2: Connecting the Wi-Fi Speaker
• Ensure the speaker is connected to the power supply. Press the WPS button to start the speaker,
then you will hear an instruction “Enter the setup mode, follow the instructions in the APP to nish the
setup”, and the power indicator ashes blue indicating that the speaker is ready to connect. Any wireless
device (such as phones, tablets, laptops etc.) can be connected. Once connected successfully, the power
indicator will become steady blue.
1. Turn on the Wi-Fi function and
connect your phone to an available Wi-Fi
network that you want.
2. Start the controller APP Smart
Sonix and click Add Device
It is recommended to power on and connect the speakers with the premises Wi-Fi network before
mounting speakers in the ceiling. This will allow easier access to the WPS button and conrm compatibil-
ity with the premises network.
Caution: Speaker Network Setup

C 0870 165mm 2 Way Round WiFi Ceiling Speaker PairC 0870 165mm 2 Way Round WiFi Ceiling Speaker Pair
5. Wait for few seconds, the device will be con-
nected to the Wi-Fi automatically. Note: After
connecting successfully, click Next.
• When the Wi-Fi ceiling speaker is rst powered
on, a WiFi connection is the rst thing for which the
speaker searches. If no wireless device is found
on whilst connecting, the speaker will activate the
RCA input after 5~20 seconds in standby.
• Wi-Fi input has the priority when Wi-Fi input and
RCA input are connected simultaneously. If the
wireless device stops streaming for 5 seconds or
more, then the speaker will switch to RCA input if
it is connected.
• The initial app password is “88888888”, which
can be reset in the Smart Sonix App.
• If the multi-room network fails the rst time,
restart all the equipment and then follow the
standard connecting instructions. If trouble
persists, press the “WPS button” located on the
front of the speaker to reset the system. Make
sure the speaker is powered during the reset.
• The wireless connection will be lost if the
distance between the speaker and the wireless
device exceeds 80m.
Notes:
3. Follow the instructions in the app and get
to your phone Wi-Fi settings to nd the “Wi-Fi
Speaker_****” in the network list and connect it.
4. Return to the Smart Sonix. Choose
the Wi-Fi the same as
the one connected in step 1, type the
password of the Wi-Fi
and click Continue.

C 0870 165mm 2 Way Round WiFi Ceiling Speaker Pair
6. Name the
device
according to the
room you will
install and click >.
7. After nishing
above settings, the
Wi-Fi speaker will be
in the device list, If
you have more than
one Wi-Fi speakers,
press + to add devic-
es and name them
accordingly. After
these steps, your
multi-room music net-
work is successfully
established.
8. Choose a
device and play
a song in you
phone to test
whether the
device works.
If ok, testing
is nished and
you can pro-
ceed to use the
speaker.
For iPhone, iPad and iMac
smart device with iOS operating
system, you can use the Wi-Fi
speaker through the Airplay
function. Connect your device to
the speaker Wi-Fi. In the pull-up
or pull-down menu, click Airplay
and choose the Wi-Fi speaker,
then the audio can be streamed
from your smart device.
Airplay Note:
Notes:

C 0870 165mm 2 Way Round WiFi Ceiling Speaker Pair
Step 1: Connect speaker power supply.
Step 2: Connect to the speakers Wi-Fi hotspot.
The SSID will appear as “Wi-Fi Speaker_XXXX” (where “XXXX” will be a unique
4 digits/letters sequence.) Default Password: 88888888
Step 3: Open a browser – (Edge, Chrome, Safari etc) and type the following IP address
into the address bar of the browser. IP address: 10.10.10.254
Step 4: Follow prompts to: Select the wireless network of the premises and enter the
premises Wi-Fi network password. Once completed the speaker will be connected to
the premises Wi-Fi network.
Step 5: Disconnect the phone/table from the speaker Wi-Fi hotspot and connect the phone/tablet
to the premises Wi-Fi network.
Step 6: Open the Smartsonix app, the speaker will now appear ready for use.
Method 2 – Direct Wi-Fi connect
Step 1: Connect speaker to network via Ethernet cable.
Step 2: Connect speaker power supply.
Step 3: Connect your phone/tablet to the Wi-Fi on the premises.
Step 4: Open Smartsonix app. The speaker will appear ready for use.
Once the speakers are connected to the premises network, remove power from the speakers and
install in preferred location.
Please Note: Final install location must still have strong Wi-Fi signal strength or Ethernet cable
available. Once power is returned, the speakers will re-connect to the network.
NOTE: It is highly recommended to install the speakers with a power source that can be power
cycled. For example A power point with an on/off switch within reach or smart home controlled
power socket.
Method 3 – Ethernet Cable
For additional pairs:
1. Open Smartsonix app.
2. Press + symbol in top right corner.
3. Follow app prompts for premises Wi-Fi details: Wi-Fi name (SSID) and password)
4. Led on speaker will ash blue and speaker will voice prompt
“Searching for Wi-Fi connection”.
Upon successful connection the LED will change to solid blue and voice prompt
“Wi-Fi connected” and the speaker will now be ready for use with Smartsonix app or Airplay.
• Turn off the power to the speaker when unused for long periods of time.
• Ensure all equipment is turned off prior to cleaning
• Surfaces need only occasional dusting/cleaning.
• Never use chemicals or solvents as they may damage the surface.
• Always clean using a dry cloth.
• Never touch the speaker drivers.
Care and Maintenance

C 0870 165mm 2 Way Round WiFi Ceiling Speaker Pair
If installing the speakers in an enterprise level network environment, please consult the network
administrator or I.T. professional to ensure the network will allow the speakers to connect.
For non-enterprise level networks such as residential and home networks:
1. Please ensure the router has the 2.4 GHz Wi-Fi band enabled. The speakers will not
connect with routers/access points that are ONLY on the 5ghz band.
2. Ensure the network’s access points are not using WPA-Enterprise mode protocol.
The speakers do not support WPA-enterprise mode.
3. Ensure the router has DHCP enabled.
4. Ensure the access points do not have a captive guest portal activated.
5. Ensure the access points are not using a hidden SSID.
6. Ensure the router is not using AP isolation, since the speakers will not appear in the
search on networks with AP isolation security.
7. Ensure the router supports Multicast (IGMP).
Wi-Fi Compatibility
1. Router Device Connection limit
Some routers have a limit for the number of Wi-Fi devices that can be connected at one time – typically
between 10 and 15 Wi-Fi enabled devices together. Please check the router specication to ensure that
this device limit is not exceeded. A router which is overloaded, trying to accommodate multiple connect-
ed devices, may drop some devices off the network.
2. Limited Signal Coverage
The further away the speakers are from the Wi-Fi router, the weaker the wireless connection, and the
more likely that drop outs will occur. The speakers do require good Wi-Fi signal strength to operate. If the
speaker location has poor Wi-Fi signal strength, then they may drop connection. Please relocate the Wi-Fi
router/access point or add Wi-Fi extenders to improve signal strength. Alternatively, consider using the
Master speaker’s RJ-45 port to install a wired connection from the speaker to the router.
Wi-Fi Connection Hints:
• Rename: If you nd the Wi-Fi speaker is wrongly named after installation, you can rename the device as
you see t using the mobile App.
• Speaker info: To protect the speaker’s Wi-Fi signal from being hacked by others, you can set a pass-
word for your device. The default password is 88888888.
Device Personal Setting:
If the multi-room network fails during operation, you can press the WPS button to restore the speaker to
its original factory default settings. Uninstall the Wi-Fi speaker from the ceiling and press the WPS button
for around 5 seconds. During this operation, make sure the speaker is power switched on.
Device Resetting:

Altronic Distributors warrants this product for one year from date of purchase from Altronics or its resellers
to the consumer. If this item is part of an installation or another product, please contact the installer or
supplier for your warranty.
During the warranty period, we undertake to repair or replace your product at no charge if found to be
defective due to a manufacturing fault. The warranty excludes damage by misuse or incorrect installation
(i.e. failure to install and operate device according to specications in the supplied instruction manual),
neglect, shipping accident, or no fault found, nor by use in a way or manner not intended by the supplier.
For repair or service please contact your PLACE OF PURCHASE.
If this item was purchased directly from Altronics please make a warranty claim by:
1. FOR MAIL ORDER CUSTOMERS (includes school and trade orders),
a) Calling your nearest store location and quoting your tax invoice number.
b) Upon contacting Altronics, we will issue an R.A. (Return Authorisation). As Altronics have a number of
service agents throughout Australia, a copy of the R.A. will be emailed, faxed or mailed to you with full
instructions of how and where to send the goods. The freight for shipping goods back to
Altronics for all repairs is at the customers expense.
c) A copy of the R.A. form, (or at the very minimum, the R.A. number) must accompany the
goods to effect the repair.
d) Altronics will pay the return freight to the customer where the warranty claim has been accepted.
e) Please quote the R.A. number in any correspondence to us.
2. FOR OVER THE COUNTER PURCHASES to make a warranty claim, please return the goods to us in
any of our stores, with a copy of your proof of purchase (tax invoice).
a) Upon leaving the goods at one of our stores, an R.A. number will be issued to you.
b) Once repaired, you will be contacted, advising that the goods are ready to be collected from the store.
It is at Altronics discretion as to whether the goods will be repaired or replaced (whilst under warranty); and
as to whether identical goods will be used to replace the item due to changes of models / products.
Note: Under no circumstances should you attempt to repair the device yourself or via a non-authorised
Altronics service centre, as this will invalidate the warranty!
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not amount to a major failure.
Distributed by Altronic Distributors Pty. Ltd.
Phone: [phone]
altronics.com.au
Revision 16/10/2020