Red Solid Power apply
LINK
Yellow or
Green
Yellow
Green
Blinking
10BaseT
100BaseT
Network data activity
READY
Green Blinking
Solid Ready/normal
Bootup/reset/malfunction
Serial (if avail.)
Green OFF
Solid
Blinking
Port not opened
Port opened
TX or TX/RX serial data activity
Serial (if avail.)
Red OFF
Solid
Blinking
Port not opened
Port opened
RX serial data activity
□Connect an Ethernet cable to the ESP/ESR unit if
connecting to a switch or crossover direct to the PC.
□Connect the power supply to the ESP/ESR unit and
a
ower.
ESP901/902/904
ESR901/902/904
□ESP901/902/904 or ESR901/902/904 unit
□Printed version of this ESP90x/ESR90x Quick Start Guide
□CD ROM containing software and a comprehensive manual
□Ext power supply (ESP901/902/904 ONLY)
C
Ch
he
ec
ck
k
P
Pa
ac
ck
ka
ag
ge
e
C
Co
on
nt
te
en
nt
t
H
Ha
ar
rd
dw
wa
ar
re
e
I
In
ns
st
ta
al
ll
la
at
ti
io
on
n
S
So
of
ft
tw
wa
ar
re
e
I
In
ns
st
ta
al
ll
la
at
ti
io
on
n
C
Co
on
nf
fi
ig
gu
ur
re
e
t
th
he
e
E
ES
SP
P/
/E
ES
SR
R
U
Un
ni
it
t
□Click Start\Programs\B&B Electronics\Vlinx\ESP
Servers\Vlinx ESP Manager and it should auto-search for
attached ESP901/902/904 or ESR901/902/904 devices on
startup.
□Note that the device must reside on the same subnet or
it won’t be seen by the Vlinx ESP Manager software for
first time discovery.
□Use the Vlinx ESP Manager software to configure the
unit for network information, serial device configurations,
timeouts, etc (double-click on your device in the list).
□Alternative method is to set the dipswitches in console
mode and use Hyperterminal set at 9600 and 8-N-1. Use
the arrow and <enter> key to configure (requires null
modem/cross-over serial cable connected to Port 1). Be
sure to set dipswitches back to run mode when done. (Not
avail. on ESP904).
□Default password = <blank>
□Reboot as necessary.
V
VC
CO
OM
M
I
In
ns
st
ta
al
ll
la
at
ti
io
on
n
□Click Start\Programs\B&B Electronics\Vlinx\Install Virtual COM
□Search for all devices (must be in same subnet). Type specific
IP address otherwise.
□Select your device from list (double click on your device).
□Follow the onscreen instructions and install to a COM number
usually 5 or above to limit interference with existing real COM ports.
□Use Hyperterminal to verify you can open your VCOM created.
S
Se
er
ri
ia
al
l
D
De
ev
vi
ic
ce
e
I
In
ns
st
ta
al
ll
la
at
ti
io
on
n
L
LE
ED
D
S
St
ta
at
tu
us
s
Connect the serial device to the unit using the correct cabling:
□Straight through serial cable for DCE serial device
□Null modem (crossover) serial cable for DTE serial device
P
Po
or
rt
ts
s
T
To
o
O
Op
pe
en
n
i
in
n
F
Fi
ir
re
ew
wa
al
ll
l
□Insert the software CD and it should autostart into the
installation wizard.
□Follow the on screen installation wizard to install the
Vlinx ESP Manager software.
Note: Be sure you have administrative rights & disable
firewalls Windows XP/Vista (see Section 8 also).
Model Switch 1 Switch 2 Switch 3
ESP901 Run/console Run/console Run/console
ESP902 Run/console Run/console Run/console
ESP904 None None None
ESR901 Run/console TB or DB9 None
ESR902 Run/console None None
ESR904 Run/console None None
NOTE: ESP01/902 must be ALL UP or ALL DOWN.
Ports Function
5300 Heartbeat & configuration setting in TCP
mode (i.e. pair tunneling mode)
8888 Vlinx update
8889 Configuration setting in UDP mode
8890 Vlinx monitor
4000/1/2/3 VCOM