VMP PDS-LCM2B User manual

PDS-LCM2B
Instruction Sheet For:
For more information, please contact us at:
345 Log Canoe Circle, Stevensville, Maryland 21666
Toll Free: 877.281.2169 Phone: [phone] Fax: [phone]
www.videomount.com

10 7
28
11
6
2
925
27
26
24 23 222120191817161413 15
3
5
12
4
8
1
PDS-LCM2
29
ITEM
NO.
DESCRIPTION
QTY.
1
Mounting Adaptor
1
2
Security Screw M5*P0.8*L20
2
3
Mounting Bracket
1
4
Extension Bracket A
2
5
Washer
5/16"*
16*T1.6
4
6
Screw 5/16" - 18UNC*L5/8"
4
7
Nylon Nut M10*P1.5
2
8
Washer
3/8"*
19*T1.6
6
9
Long Allen Key M4
1
10
Screw M10*P1.5*L25
2
11
Adjusting Bracket
1
12
Adjusting Screw M12*P1.75*L100
1
13
Screw M4*P0.7*L12
4
14
Screw M5*P0.8*L12
4
15
Screw M6*P1.0*L12
4
16
Screw M8*P1.25*L16.5
4
17
Screw M4*P0.7*L30
4
18
Screw M5*P0.8*L30
4
19
Screw M6*P1.0*L35
4
20
Screw M8*P1.25*L40
4
21
Lock Washer M4
4
22
Lock Washer M5
4
23
Lock Washer M6
4
24
Lock Washer M8
4
25
Washer
5.5*
18*T2
4
26
Spacer M6
4
27
Spacer M8
4
28
Extension Bracket B
2
29
Washer
5*
15*T1.0
2

Step 1
Before starting, lay out all parts to your mount and match them to
the parts list provided. Verify that you have all your parts before
attempting to assemble the mount.
Note: For these instructions PDS-LCB part numbers have hexagons
around their numbers and PDS-LCM2B part numbers have circles
around their part numbers.
Step 2
Attach the adjusting brackets PDS-LCM2B / PDS-LCB to the
mounting adaptor PDS-LCM2B using the M10 screws PDS-
LCM2B / PDS-LCB, washers PDS-LCM2B / PDS-LCB and
nylon nuts PDS-LCM2B / PDS-LCB. Insert the adjusting screw
PDS-LCM2B / PDS-LCB into the welded nuts located in
the mounting adaptor PDS-LCM2B Note: You will have to
thread the rst adjusting screw all the way down to provide space
to thread in the second screw. Once the second screw is started
you can back off the rst to the desired tilt angle.
Step 3
Mark the ceiling or desired mounting surface in preparation of
installation of ceiling plate PDS-LCB. If mounting to wooden
ceiling joists, pre drill pilot holes using a 7/32” drill bit. Attach the
ceiling plate PDS-LCB to the wooden ceiling joist using the
5/16” by 2.5” long lag screw PDS-LCB and washer PDS-LCB.
WARNING: Please verify that your mounting surface will support
the combined weight of your mount, mounting hardware, and at
panel. Also verify that the mounting surface is safe to drill through.
Please note only mounting hardware for mounting to wooden ceil-
ing joists will be provided with the unit. If mounting to a surface
other than wooden ceiling joists then other hardware will be re-
quired. If in doubt or uncertain about any of the above, please
contact a professional installer.
Step 4
Screw the outer mast PDS-LCB into the ceiling plate PDS-
LCB. Secure the outer mast by tightening the brake screw PDS-
LCB into the thread hole in the side of the ceiling plate. Attach
the inner mast PDS-LCB to the outer mast using the M8 screw
2PDS-LCB and nylon nut PDS-LCB. Attach the pipe couple
PDS-LCB to the bottom of the inner mast and secure the pipe
couple with a brake screw PDS-LCB.
Step 2 : Attaching the adjusting
brackets
Step 3: Attaching the ceiling
plate to the ceiling
Step 4 : Attaching the ceiling
mast to the ceiling plate
8
1
11
WARNING: The installer of these products must verify that the mounting surface, ceiling or
wall, will safely support the combined weight of all attached equipment and hardware.
Video Mount Products will not be held liable for the improper use or installation of its products.
10
7
12
1
25
10 22
21
26
1
1
19
46
21
11
3
1312
4
11

Step 5
Attach the mounting adaptor PDS-LCM2B to the pipe couple
PDS-LCB using the metal washers PDS-LCB, PVC washers
PDS-LCB and nylon nut PDS-LCB. After tightening down
the nylon nut completely insert the cotter pin PDS-LCB though
the hole in the bottom of the screw of the pipe couple.
Step 6
Slide either extension brackets A or B or PDS-LCB / or
PDS-LCM2B onto the mounting plate PDS-LCB / PDS-
LCM2B and match up the slots on the extension brackets to the
holes on the back of your TV. Determine the correct screw size
and if you need to use washers, lock washers, or spacers. Note:
Spacers are used for TVs with recessed hole patterns. Secure the
TV to the extension brackets or PDS-LCB / or PDS-
LCM2B using the appropriate hardware through PDS-LC/
through PDS-LCM2B. Secure extension brackets with
5/16” screw PDS-LCB / PDS-LCM2B and washer PDS-
LCB / PDS-LCM2B.
Step 7
Lift the mounting bracket PDS-LCM2B / PDS-LC onto the
adjusting bracket PDS-LCM2B / PDS-LCB. WARNING: This
step requires at least two people to prevent possible injury. Secure
the plates together using the M5 security screw PDS-LCM2B /
PDS-LCB and washer PDS-LCM2B / PDS-LCB.
Please verify that all nuts and screws are securely tightened.
Step 5 : Attaching the mounting
adaptor to the pipe couple
27
28
WARNING: The installer of these products must verify that the
mount surface, ceiling or wall, will safely support the combined
weight of all attached equipment and hardware. Video Mount
Products will not be held liable for the improper use or installation
of its products.
Enjoy Your Mount!
1
13
4
Step 6A: Attaching the mounting rails
to the at panel
(holes are not recessed)
Step 6B: Attaching the mounting rails
to the at panel (holes are recessed)
Step 7: Attaching the mounting
brackets to the adjusting brackets
46
44 7
45
18 42
3
17
28
4
18 42
27 41
6
20
5
19
17
3
11 25
2
16 29 43