VOGELS PFW 6850 User manual

Max: 45kg/100lbs
MOUIN_PFW6850_V01
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
PFW 6850

www.vogels.com
M6 x 16mm M6 x 25mm M8 x 16mm M8 x 25mm 5/16” Washer 5/16” x 3”
Lag Bolt Universal Spacer Universal Washer Finned Anchor
2.5mm Allen Key Depth Measuring
Straw
Level4mm Allen Key
Phillips
Screwdriver
Protective Eyewear Hammer
Leveler
Electronic Stud
Finder
Pencil Drill Gun
2.5mm Allen Key
10mm Socket
Template
x4 x4 x4 x4 x4 x4 x8 x4 x4
1/4” / 6mm
Drill Bit
3/8” Concrete
Drill Bit
Socket Wrench 13mm or 1/2”
Socket
x1 x1 x1 x1 x1 4
A2A1 Remove the plastic hole covers from the upper and lower
plates. Loosen the (2) set screws on the plate using the
2.5mm allen key supplied. Reposition the upper and lower
pivot rods to mate to either the center or right side pivot
receiver holes, push the upper and lower plate fully on to the
rods, and re-tighten the set screws. Reinstall the side plate
with the eight flat head screws and confirm they are secure.
Reinstall the round plastic hole covers.
Prior to initial step 1 of the installation, your PFW 6850 can
easily have the main “swing left” pivot point of the main swing
out arm moved to either the center, left or right of the mount
by simply placing the mount on a flat surface and removing
the eight flat head screws, then separating the upper and
lower wall plates.
Included components
Required for installation
Pivot
Set Screw
Locations
Set Screw
Locations

www.vogels.com
12
443
2
1
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
PFW 6850
To ease the installation process you have the option to
remove the wide front plate and mounting brackets by simply
removing the three M5 x 10mm flat head screws, holding
the plate assembly to the swing out arm assembly and set-
ting them aside.
Take the thick cardboard mounting template supplied and
place the it over the mounting studs with the screen center
facing up. Confirm that the template is level horizontally and
that the wall place outline is to the center of your desired
height.
Using a suitable stud-finder device for frame walls, mark the
position of the stud centers.
Measure the desired height of the center of the screen and
mark it.
Using a 1/4” or 6mm drill bit, drill pilot holes minimum 2”
(50mm) deep into the four marked mounting points on the
wall surface. For solid concrete wall construction, the sup-
plied plastic wedge anchors are recommend to be used with
the 5/16” x 3” (76mm) lag bolt and washers supplied.
1/4” / 6mm

www.vogels.com
12
487
6
5
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
PFW 6850
Take the plastic depth straw supplied and confirm the overall
“safe” screw depth that can be used.
Re-install the front wall arm plate to the arm with the three
M5 flat head screws you set aside earlier. Confirm screws
are fully seated and tight.
Wood Stud
Leveler
1/2”
x4
x4
Raise the PFW 6850 assembly so the mounting slots
are over the four drilled mounting holes. Confirm mount
level with spirit level and secure the mount to the wall
surface with the four each 5/16” x 3” (76mm) lag bolt
and 5/16” flat washer supplied.
Level the wall mount in the following order on figure 5
and below
Re-confirm secured assembly is level horizontally and
vertically or level again if necessary before proceeding.
NOTE: Do not over tighten lag bolts
Concrete Wall
Leveler
1/2”
x4
x4x4
1. Level the wall mount in following order on figure 6
and below.
2. Mark the pointing points.
3. Drill the concrete wall using a 3/8” concrete drill bit.
4. Lighty hammer the four (4) Finned Anchors into the wall.
5. Tighten the (4) 5/16” washers and (4) 5/16” x 3” (76mm) lag
bolts into the wall.

www.vogels.com
12
4
10A
11
9
10B
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
PFW 6850
Once the correct pitch and depth screws are pulled from
the hardware pack supplied, secure the two brackets to the
rear of the display with the proper screws and plate washer
holes. Plastic spacers are also supplied in case you need
additional clearance between the bracket and the rear of the
display. NOTE: Do not over tighten the screws.
With the upper and lower security screws loosened on each
bracket (two people recommended) raise the display and
place the top hook of the bracket over the receiver plate on
the wall mount. Allow the lower end of the bracket to lay flat
against the mating plate on the mount.
Center the display horizontally on the plate and check the
display is level on the mount. To adjust level, adjust the left
or right top screw to achieve desired level of the display.
Once level, secure the lower left and right security screws
on the bracket to “fix” the mount to the wall mount.
x4x4
x4x4
Place the display face down on a smooth flat surface. Place
the left and right mounting brackets over the four mounting
points on the rear of the display arrow pointing up to the top
of the display, making sure the brackets are lined up with the
center top to bottom on the display.

www.vogels.com
12
1514
13
12
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
PFW 6850
We recommend where possible that the power and signal
cables be run separately through the mount until mating at
the display plug in points to minimize possible “cross talk”
interference. With the covers removed, cable can be run
inside the upper and lower main arm and through the slots
behind the plastic beauty covers.
Install the upper and lower “push on” plastic “beauty covers”
to the upper and lower wall plates. Reinstall the upper and
lower plastic cable covers to the mounts main swing arm.
Installation complete
10mm Deep Socket
2.5mm Allen key
2.5mm Allen key
Tilting of the display on the mount is easily accomplished by
placing one hand on top of the display edge center and one
hand on the bottom of the display edge center and gently
pulling out on the top edge to the desired tilt angle. No lock-
ing of the set tilt angle is required as the mount has built-in
friction control. If additional tension is required, use the
socket and M4 allen key to adjust the desired tension.
Extra tension can be applied to the pivot of the arms by
tightening the nuts on the arm with supplied 10mm deep
socket, and the set screws on the base with the supplied
2.5mm allen key. NOTE: Do not over tighten.

www.vogels.com
24.80
630
20.73
526
21.38
543
1.00
25
15.86
403
29.49
749
15°
MAX TILT
32.20
818
12.56
319
1.60
41
26.33
669
23.06
586
16.00
406
18.00
457
23.66
(D2)
601
10.50
(D1)
267
(MULTI POSITION ARM 3 PLS)
NOTE: IF THE NEXT ARM OPTIONAL
POSITION IS USED ADD 7" TO (D1) & (D2)
12.12
308
1.85
47
1.50
38
21.00
(D1)
533
34.16
(D2)
868
(MULTI POSITION ARM 3 PLS)
NOTE: IF THE NEXT ARM OPTIONAL
POSITION IS USED ADD 7" TO (D1) & (D2)
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
PFW 6850
95V0-000-015-0X_2