VOGELS PFW 6851 User manual
INSTALLATION INSTRUCTIONS
9531-007-Z00-0
PFW 6851
Display Wall Mount, Turn & Tilt 80 kg
Page 2 Installation Instructions
Table of Contents
Warning Statements
Warning Statements 2
Parts List 3
Installation Tools 3
Wood Stud Installation 5
Concrete Surface Installation 7
Determining the Mounting Hardware 8
Universal Spacer Installation 9
Griplate™Installation 9
Mounting Bracket Installation 10
Adapter Plate Installation (optional) 11
Attaching the Flat Panel to the Wall 12
Securing and Leveling the Flat Panel 12
Adjusting the Flat Panel Tilt 13
Plastic Channel Cover Installation 13
Warranty 15
PFW 6851
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND
COMPLETELY UNDERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND
PROPERTY DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE
REFERENCE.
VOGEL’S DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY VOGEL’S
PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED
ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS,
ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER
RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS.
THE SURFACE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF THE FLAT PANEL. IF NOT, THE
STRUCTURE MUST BE REINFORCED. THE MAXIMUM WEIGHT THAT CAN BE USED WITH THIS PRODUCT IS 79 KG. PROPER
INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE INSTALLATION INSTRUCTIONS,
MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN DEATH.
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER SAFETY
GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.
panel.
recommended.
damage to the mounting surface.
This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.
Installation Instructions Page 3
Parts List
PFW 6851
Installation Tools (not supplied)
Phillips Screwdriver Electronic Stud Finder Drill Level
Wrench
Tape Measure
Universal
Thread Depth
Indicator (Qty 1)
Swingout Arm (Qty 1)
Griplate™ (Qty 6)
Universal Mounting Brackets (Qty 2)
M8 Nylon Nut
Channel Covers (Qty 6)
PFW 6851
Installation Instructions Page 5
PFW 6851
Wood Stud Installation
THE FOLLOWING STEPS MUST BE PERFORMED BY TWO PEOPLE.
Wall Stud
Electronic
Stud Finder
Step 1. Determine the desired viewing location. Use a
viewing location.
Step 2
to mark the center of each stud.
Step 3. Drill a pilot hole at the marked location using a
Bit
Wall Stud
Two people must perform the installation. One
person must hold the mount while the other person
levels the mount. The mount must remain in place
while the mounting hardware is tightened.
pilot holes.
used in the installation of this product.
Upper Mounting
Channel
Mounting Slot
Flat Washer
Wrench
Step 4. Level the mount.
Step 5. Align the mounting slot with the drilled hole.
Step 6
at this time.
attaching the mount to the wall. Improper
installation may result in personal injury or
damage to property.
When determining viewing height, the center
of the TV should be at eye level while sitting in
as room decoration, raise it to the point where
the bottom of the screen is at eye level while
sitting and the top is eye level when standing.
Page 6 Installation Instructions
PFW 6851
attaching the mount to the wall. Improper
installation may result in personal injury or
damage to property.
Step 10. Re-level the PFW 6851.
Step 11
points (2 for the upper mounting channel and
2 for the lower mounting channel).
Upper Mounting Channel
Mounting Slot
Flat Washer
Wrench
Before drilling the second mounting hole,
re-level the mount.
Step 7. Drill a pilot hole at the marked location using a
Step 8. Align the mounting slot with the drilled hole.
Step 9
at this time.
Repeat these steps to secure the lower mounting channel
to the wall.
used in the installation of this product.
Installation Instructions Page 7
PFW 6851
Concrete Surface Installation
hardware, please follow the installation instructions as provided with that hardware.
THE FOLLOWING STEPS MUST BE PERFORMED BY TWO PEOPLE.
Level
Mark
Step 1. Determine the desired viewing location.
Step 2. Place the mount into position against the
wall and level the mount.
Step 3.
mount.
Step 4.
Step 5.
each hole.
Step 6. Use a hammer and lightly tap each anchor into place
so that only the threaded shaft of the concrete wedge
anchor is protruding from the wall.
Concrete Wedge Anchor
Drill HammerThreaded Shaft
When determining viewing height, the center
of the TV should be at eye level while sitting in
as room decoration, raise it to the point where
the bottom of the screen is at eye level while
sitting and the top is eye level when standing.
Page 8
PFW 6851
Determining the Mounting Hardware
Step 7. Once all of the anchors are in place, move
Step 8. Attach the nut onto the threaded shaft that
is protruding from the wall.
Step 9. Re-level the wall plate and tighten all
concrete wedge anchor nuts at this time.
hardware, please follow the installation instructions as provided with that hardware.
Threaded
Shaft
Nut
Level
Do NOT over-tighten the concrete wedge anchors.
Small Straw or Toothpick
Small Straw
or Toothpick
Small Straw
or Toothpick
Marking the 1/8”
Allowance
Depth Plus 1/8” Allowance
Mark
Depth Plus 1/8” Allowance
Mark
n Insert a small straw or toothpick into the threaded inserts found on the
o Use a pencil to mark the depth of the threaded insert on the small straw or
p Mark the straw or toothpick 1/8” above the depth of the threaded insert, as
q Insert the small straw or toothpick into the remaining threaded inserts
to compare and verify their depth using the straw or toothpick’s 1/8”
r
If the screw you selected is longer than the 1/8” allowance mark on the
small straw or toothpick, as shown in Figure 2 and Figure 3, do not use
s
The correct screws should thread easily into the mounting point and not
You must account for the bracket, spacers and Griplate™
depths when using the Thread Depth Indicator to measure
Installation Instructions Page 9
PFW 6851
Universal Spacers Installation (optional)
mounting points, please use the provided universal spacers.
EXAMPLE:
use the M8 mounting points.
Griplate™ Installation
DIMPLES
FACING UP
DIMPLES
FACING DOWN
DIMPLES
FACING UP
DIMPLES
FACING DOWN
Pre-install the mounting screws, universal
spacers and Griplates™. Once mounted, push
then tighten the rest of the hardware. Repeat
this process for the installation of the remaining
Dimples
M4
M5
M6
M8
Page 10 Installation Instructions
PFW 6851
Mounting Bracket Installation
Do NOT over-tighten the screws.
Step 1.
Step 2.
Step 3.
Mounting Hardware
Griplate™
Universal Spacer
Mounting Bracket
Mounting Point
Flat Panel
Installation Instructions Page 11
PFW 6851
Adapter Plate Installation (optional)
Do NOT over-tighten the screws.
Step 1
adapter plates.
Step 2
Step 3. Using a screwdriver, insert and tighten the
mounting hardware and adapter plates to the
screws.
Step 4.
the threaded mounting studs that are on the
adapter plate.
Step 5.
threaded mounting stud.
Step 6. Thread one (1) M8 nylon nut onto each
threaded mounting stud.
Step 7.
the M8 nylon nuts. Do not over-tighten the
screws.
level and aligned with each other. If they are
sit properly when mounted to the PFW 6851.
Griplate
Mounting
Hardware
Flat Panel
Adapter Plate
Flat Washer
Nylon Nut
Universal Mounting
Bracket
Adapter Plate
Socket Wrench
Page 12 Installation Instructions
PFW 6851
Attaching the Flat Panel to the Wall Plate
Upper
Mounting
Bar
Lower
Mounting
Bar
Flat Panel
Two people are required for this step.
Step 1.
Securing and Leveling the Flat Panel
Screwdriver
Locking
Screw
(Pre-installed)
Leveling
Screw
(Pre-installed)
Step 1. Use a screwdriver to adjust the
located on the top of the
is tilted too far to one side, the
leveling screws will allow you
simply adjusting the screws
with a screwdriver (see
illustration to the right for a
clearer view).
Step 2
screwdriver to tighten the two (2)
over-tighten these screws.
Installation Instructions Page 13
PFW 6851
TO ADJUST THE TILT TENSION OF THE PFW 6851, LOOSEN THE TENSION BOLTS LOCATED ON THE
BOTTOM RIGHT AND LEFT SIDE OF THE MAIN ARM ASSEMBLY. RE-TIGHTEN THESE BOLTS TO ACHIEVE
YOUR DESIRED TENSION.
Adjusting the Flat Panel Tilt
Step 1. Place one hand at the center top edge of
Step 2. Place the other hand on the center
Step 3. Using the upper hand, gently pull the
while the lower hand gently pushes the
wall.
Step 1. Place one hand at the center top edge of
Step 2. Place the other hand on the center
Step 3. Using the upper hand, gently push the
while the lower hand gently pulls the
wall.
Adjusting the Flat Panel Down Adjusting the Flat Panel Up
Plastic Channel Cover Installation
Side Cover
(Long)
Center Cover
(Short)
Side Cover
(Long)
Step 1. Place the plastic channel covers over
the mounting plate (2 side covers and 1
center cover).
Step 2. Gently push each cover into place,
covering the mounting slots of the
mounting plate.
Tension
Bolt
Tension
Bolt
Repeat steps 1 and 2 for the installation
of the lower plastic channel covers.
PFW 6851
All measurements are in inches(mm).
28.94
735
20.40
518.2
.38
9.5
21.59
548.41
22.23
564.63
3.11
79
30.19
766.8
28.18
715.8
15.90
403.9
10°
14.02
356
33.21
843.5
34.31
871.4
25.71
653
26.4
671.2
.41
10.31
.38
9.53
12.52
317.9
.41
10.3
16.00
406.4
18.00
457.2
24.00
609.6
(OPEN BACK) (OPEN BACK)
Other manuals for PFW 6851
1
Table of contents
Other VOGELS Rack & Stand manuals
VOGELS
VOGELS TVM 3840 Series User manual
VOGELS
VOGELS UNIVERSAL Series User manual
VOGELS
VOGELS THIN 345 User manual
VOGELS
VOGELS PFW6852 User manual
VOGELS
VOGELS VFW 030 - VFW 032 VFW 130 VFW 132 User manual
VOGELS
VOGELS PLW 1004 User manual
VOGELS
VOGELS EFW 8206 User manual
VOGELS
VOGELS EPA 6505 User manual
VOGELS
VOGELS MOMO Motion+ 4127 User manual
VOGELS
VOGELS WALL 2225 User manual
VOGELS
VOGELS WALL 2045 User manual
VOGELS
VOGELS WALL 2125 User manual
VOGELS
VOGELS VFW 226 - VFW 326 VFW 426 User manual
VOGELS
VOGELS NEXT 7346 User manual
VOGELS
VOGELS PFW 6851 User manual
VOGELS
VOGELS SOUND 3205 User manual
VOGELS
VOGELS EFW 8105 User manual
VOGELS
VOGELS WALL 2105 User manual
VOGELS
VOGELS EFW 8105 User manual
VOGELS
VOGELS SOUND 1250 User manual
Popular Rack & Stand manuals by other brands
Evolution
Evolution 005-0002 Original instructions
System Sensor
System Sensor BEAMMMK Installation and maintenance instructions
Helios
Helios ultra Silence ELS-GUBA Installation and operating instructions
CHIEF
CHIEF ESS-42 installation instructions
Havis
Havis UT-201 owner's manual
DATAMATION SYSTEM
DATAMATION SYSTEM DS-MDM-SC-16U-IPL user guide
idi
idi 1000F Series Installation and maintenance guide
HP
HP cc2300 installation instructions
TradeQuip
TradeQuip 1895T owner's manual
ULTIMATE SPEED
ULTIMATE SPEED 285700 Assembly, operating and safety instructions
Barpa
Barpa NORMA 800 Series installation instructions
CONEN
CONEN LI8050W Assembly instruction
Central Machinery
Central Machinery 61700 Owner's manual & safety instructions
Unicol
Unicol AZENITH VSX1800SC instruction manual
HiFiMAN
HiFiMAN SHANGRI-LA owner's guide
Advantech
Advantech DLT-V73 Series Mounting instructions
Mark Bric
Mark Bric ISOframe IS-9103 Mounting instructions
peerless-AV
peerless-AV ACC 912 instructions