VOGELS PFW6855 User manual

9531-060-Z00-01 www.vogels.com
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
PFW6855

www.vogels.com
9531-060-Z00-01
1
1
x2
x6
5/16” x 3” 5/16” M6 x 12mm M8 x 10mm
M8 x 16mm M8 x 20mm M8 x 30mm
M5 x 6mm
x6 x2
x4 x4 x4
x4
x8
x1 x1
x1
Included components
Required for installation
Drill Template
Refer to
Step: 3
10
10 3
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
PFW6855
2.5mm
5/32”
1/4” / 6.5mm
M10 1/2”/13mm
Stud Finder
Note: It is extremely important that this installation be
carried out by well qualified installation personal and the
mounting surface capable of supported the weight of the
display mount together through out the articulating range of
the PFW6855 series mount.

www.vogels.com
9531-060-Z00-01
1
3
2
4
6A
5
4
3
x1
x1
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
PFW6855
2 3
1/2 ”/13 mm
1/4” / 6.5mm
4 5
With minimum two people place the PFW6855 wall plate
assembly and secure to the wall using the top center hole of
the wall plate.
With a spirit level place on top of the wall plate level the
mounts than secure the remaining bolts through the wall
plate to the wall.
Take the mounting template supplied insure the template
is centered and level at the desired height on the mounting
surface. Mark the mounting hole (six recommended) three
on top and three on bottom.
Note: drill mounting pilot holes to a proper depth to insure
the lag or wedge anchor bolts are fully engaged into the
hole.

www.vogels.com
9531-060-Z00-01
1
3
2
4
9A
8
6B 7
Make sure to keep space between
the bracket and display.
x4
x4
x4 x4 x4
M8 x 16 mm M8 x 20 mm M8 x 30 mm
or or
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
PFW6855
1/2 ”/13mm
6
7
8 9
5/32”
Remove the two security screws from the right and left side
of the mounting bracket crossbar and slide the two mounting
brackets inside the left and right side security screw hole
and reinstall the two security screws.
Remove the two security screws from the right and left side
of the mounting bracket crossbar and slide the two mounting
brackets inside the left and right side security screw hole
and reinstall the two security screws.

www.vogels.com
9531-060-Z00-01
1
3
2
411B
11A
10
9B Make sure to keep space between
the bracket and display.
x4
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
PFW6855
5/32”
5/32”
C
L
Invert the flat panel display and place it on a smooth flat
surface so the back of the display panel is facing up.
Align the two mounting bracket to the four mounting points
on the rear of the display and secure them bracket to the
display with the proper “pitch” supplied hardware. Check the
owners manual to determine correct pitch hardware recom-
mended.
Once the mounting brackets are secured to the rear of the
display, align the round portion of the cross bar so it is on
dead center of the display from left to right side.
Secure the cross bar to the bracket using the four Allen
head screws supplied.

www.vogels.com
9531-060-Z00-01
1
3
2
41514
13
12
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
PFW6855
Once all mounting points and level of the display have been
confirmed, remove the plastic covers to route cable from the
wall to the display.
Note: appropriate number of personal and possible installa-
tion lift aids lift and insert the round portion of the crossbar
with display attached and safely insert the round portion of
the cross bar into the open round receiver portion on the
wall mount.
Remove the 6mm knurl knob safety screw and set it aside.
With the cross bar fully seating
into the receiver reinstall the
6mm safety knurl knob.

www.vogels.com
9531-060-Z00-01
1
3
2
41918
17
16
With the 2.5mm Allen head wrench supplied, install the two
each M5 x 6mm mini adjustment Allen head screws supplied
to both sides of the “rotation” stop bar. Slowly turn the display
to the level position in each direction and adjust the two adjust
screw to set max rotation in each direction to level.
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
PFW6855
M2.5
M10 M5 x 6 mm
=14mm wrench socket
x2
The PFW6855 has a unique “load offset adjustment” feature
that allow for the heavier weight displays to be tilt corrected
past base center back to level from top to bottom. With
personal lifting gently “out “ on the bottom of the display a
9/16” (14mm) socket may be used to increase or decrease
the tilt feature of the mount.
The two side mounted screws in the receiver head of the
mount can be adjusted to add or subtract tension in the rota-
tion of the display in the mount.
Power and signal cables may be conveniently run through
the arms of the mount between the display and the power
and signal source to assist in the clean look of the cable
installed.
Note: Once cables have been installed carefully check the
movement of the mount and cables together to insure their is
no “pinching of the cables” when the mount is articulated.

www.vogels.com
9531-060-Z00-01
6
3
4
2
5
1
4
1
3
2
6
5
3
2
1
6
4
5
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 3106-000-036-XX
MOUNTING BRACKET WELD ASSEMBLY
(ELLIPTICAL)
2
2
6095-PSD-E-E
PLASTIC CAP (ELLIPTICAL TUBE 3.149 X
1.574 )
2
3
3106-000-034-XX SWIVEL TUBE ASSEMBLY 1
4
0474-061-104-6X SCREW PAN PHILLIPS COMB (M6X1.0 X 12) 2
5
1658-079-091-6X SET SCREW CUP POINT ( M8 X 1.25 X 10 ) 4
6
1658-052-061-6X SET SCREW CUP POINT ( M5 X 0.8 X 6 ) 2
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 3106-000-037-XX
MOUNTING BRACKET ASSEMBLY LARGE
(ELLIPTICAL)
2
2
3106-000-035-XX SWIVEL TUBE ASSEMBLY (LARGE) 1
3
6095-PSD-E-E
PLASTIC CAP (ELLIPTICAL TUBE 3.149 X
1.574 )
2
4
0474-061-104-6X SCREW PAN PHILLIPS COMB (M6X1.0 X 12) 2
5
1658-079-091-6X SET SCREW CUP POINT ( M8 X 1.25 X 10 ) 4
6
1658-052-061-6X SET SCREW CUP POINT ( M5 X 0.8 X 6 ) 2
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 3106-000-035-XX SWIVEL TUBE ASSEMBLY (LARGE) 1
2
6095-PSD-E-E PLASTIC CAP (ELLIPTICAL TUBE 3.149 X 1.574 ) 2
3
0474-061-104-6X SCREW PAN PHILLIPS COMB (M6X1.0 X 12) 2
4
3106-000-038-XX MOUNTING BRACKET ASSEMBLY XLARGE (ELLIPTICAL) 2
5
1658-079-091-6X SET SCREW CUP POINT ( M8 X 1.25 X 10 ) 4
6
1658-052-061-6X SET SCREW CUP POINT ( M5 X 0.8 X 6 ) 2
9
1
5
108 6
17
19
16
2
7
13
11
415
21
20
22
14
18
3
12
ITEM NO. QTY. PART NO. REV DESCRIPTION
1 2 3106-000-032-XX 00 WALL BRACKET TUBE WELDED ASSEMBLY (ELLIPTICAL)
2 2 3106-000-031-XX 01 DOUBLE ARM TUBE WELDED ASSEMBLY
3 2 3106-000-033-XX 00 SHORT ARM WELDED ASSEMBLY (ELLIPTICAL)
4 2 2482-21-AM3 01
SHAFT .75 X 12" LONG
5 2 2482-22-AM3 01 SHAFT .75 X 20" LONG
6 26 2482-23-AM3 00 COVER,OBLONG HOLE COVER (PLASTIC)
7 10 0700-205-226-XX 00 TUBE/PIPE END CAP COVER 1.181 X 1.375 X .616
8 8 6095-PSD-E-E 00 PLASTIC CAP (ELLIPTICAL TUBE 3.149 X 1.574 )
9 12 0477-087-147-6X HEX FULLY THREADED 3/8"-16 x 3/4"
10 20 2482-36-AM3 01 BUSHING FLANGE DIE CAST .750 ID X 1.180 OD X 1.395 FLANGE .
11 10 204X-57A-L00-69 3/8" WASHER NON-STD (.405 ID) X (1.062 OD) X (.098 THK)
12 2 204X-578-502-10 3/8" WASHER NON-STD (.406 ID) X (.748 OD) X (.066 THK)
13 12 204X-86B-N00-28 WASHER DELRIN (.765 ID) X (1.400 OD) X (.020 THK)
14 1 3106-000-022-XX 03 ROTATIONAL MOUNT ASSEMBLY
15 2 3106-000-013-XX 00 SHAFT .75 X 6.67" LONG
16 10 2270-45A-E01-45 00 1" X .3 VINYL FEET
17 10 0548-061-077-6X SCREW TRUSS HEAD COMBO PHILLIPS (M6X1.0X8)
18 2 3106-000-003-XX 00 INTERNAL ROTATION TUBE
19 8 1658-061-077-6X SET SCREW CUP POINT ( M6 X 1.0 x 8 )
20 1 3106-000-024-XX 00 ROTATIONAL STOP
21 2 0422-061-104-6X SCREW FLAT 90 DEGREES PHILLIPS (M6 x 1.0 x 12)
22 1
0562-061-077-6X
00
SCREW KNURL KNOB PHILLIPS (M6X1.0 X 8)
Installation Guide
Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids
PFW6855