Volair Sim G1000 User manual

www.volairsim.com
AVIONICS PANEL G1000
P/N: VS-AP1-G1000
ASSEMBLY INSTRUCTIONS
Rev. 1.0
© Volair Sim. All Rights Reserved.

PAGE
1
Thank you for purchasing the Avionics Panel G1000 for the Volair SimTM chassis! We hope that it will further
increase the sense of realism and immersion during flight simulation. Although we have designed the
Avionics Panel with ease of assembly in-mind, please read these instructions carefully first.
NOTE: SOME OF THE PARTS MAY VARY FROM THOSE SHOWN IN THE PHOTOS BELOW AS
WE CONTINUOUSLY IMPROVE OUR PRODUCTS. PLEASE ALSO VISIT OUR YOUTUBE CHANNEL
FOR ADDITIONAL INSTRUCTIONS AND TIPS.
The Volair Sim Avionics Panel G1000 is compatible with the following accessories:
• Volair Sim chassis (all versions)
• RealSimGear G1000 Suite (PDF, MFD, GMA audio panel)
• Yokes:
o Honeycomb Alpha Yoke
o Logitech (Saitek) Pro Flight Yoke
o Brunner Yoke
o Yoko Yoke
• Honeycomb Bravo Throttle Quadrant
• Up to two (2) Logitech (Saitek) Pro Flight (rectangular) instruments. One instrument can be mounted
to the left of Yoke. Second instrument can be mounted in the space reserved for the Honeycomb
Bravo Throttle Quadrant using the provided adapter plate.
• Up to three (3) Logitech (Saitek) Flight Instrument Panels (e.g. Airspeed Indicator, Attitude Indicator,
and Altimeter as back-up instruments) that can be mounted using the provided adapter plate.
• AMPS STANDARD (38mmx30mm) ball mount drill pattern and space for attaching a tablet (e.g. iPad
or iPad mini). Note: Ball mount is not provided.
o Example: RAM Mounts Ball Adapter with AMPS Plate RAM-B-347U with B Size 1" Ball

PAGE
2
Volair Sim Avionics Panel G1000 ships with the following adapter plates:
1. Blanking Plate for Logitech Pro Flight Accessory (Left of Yoke)
2. Adapter Plate for attaching Additional Logitech Flight Instrument Panels
3. Blanking Plate for Honeycomb Bravo Throttle (Right of Yoke)
4. Adapter Plate for Additional Logitech Pro Flight Accessory (Right of Yoke in-place of Bravo Throttle)
Volair Sim Avionics Panel
G1000 ships with the seat
riser kit (P/N: VS-SRK) which
allows the Volair Sim Chassis
users to increase seat height
by 3” to improve monitor
visibility over the panel glare-
shield.
To install this kit, see
Appendix C for instructions.
1
2
3
4

PAGE
3
ASSEMBLY INSTRUCTIONS
STEP 1: Unpack the Volair Sim G1000 Avionics Panel and lay it front-down on a soft surface in order to
protect the panel and the RealSimGear (RSG) components. Next, test-fit the RealSimGear PFD and MFD
displays to ensure that the four (4) mounting holes in the Avionics Panel align with the respective holes in the
PFD and MFD. Due to very close tolerancing and placing of the RSG mounting holes, this step is very
important.
NOTE: IN CASE THE MOUNTING HOLE ALIGNMENT
OF THE MFD IS NOT SQUARE WITH THE EDGE OF
THE PANEL, REMOVE THE MFD AND GENTLY BEND
THE END OF THE AVIONICS PANEL AND TEST FIT
AGAIN.
DO NOT ATTEMPT TO FORCE THE INSTALL OF THE
PFD AND MFD UNLESS YOU VERIFY THE MOUNTING
HOLE ALIGNMENT AS DAMAGE TO THE PFD/MFD
MAY OCCUR!
The PFD and MFD are mounted using M3 machine screws
inserted from the rear of the Avionics Panel which are
included with the RealSimGear G1000 suite.
Once you install the PFD and MFD, you can install the
RSG GMA audio panel as shown on the photo on the
right using the brackets hardware provided with the RSG
GMA Audio Panel. Use the four (4) machine screws
(circled in RED) to gently tension the audio panel against
the Avionics Panel face.
WARNING: DO NOT OVERTIGHTEN AND DO NOT SUBSTITUTE LONGER SCREWS THAN
PROVIDED BY REAL SIM GEAR OR THE SCREWS MAY PENETRATE THROUGH THE FACE OF
THE G1000 HOUSING!

PAGE
4
STEP 2: Detach all avionics/accessories from the Volair Sim avionics table except for the yoke (if installed). If
you do not have the yoke installed, test-fit it now. Volair Sim Avionics Panel G1000 is compatible with the
following flight yokes: Logitech (Saitek), Honeycomb Alpha, Yoko, and Brunner.
If installing the Honeycomb Alpha yoke and/or Honeycomb Bravo throttle, please see the Appendices A and
Brespectively for installation details.
Open the Bag Labeled “Avionics Table Attachment Hardware.” Inside, you will find a set of eight (8)
M4x12mm flat head Phillips machine screws, nuts, and washers and a universal wrench as shown below:
STEP 2A: Begin by attaching the longer extender bracket to the RIGHT side of the Volair Sim Avionics Table
using two M4x12mm flat head Phillips machine screws, nuts, and washers as shown below. Use the universal
wrench to prevent the nuts from turning while tightening.

PAGE
5
STEP 2B: Next, place the smaller extender bracket on top of the longer extender bracket and verify that the
two open holes line-up properly and that the front lip of the avionics table is uniform with the bracket as
shown:

PAGE
6
STEP 3: Use the rightmost two holes on the extender bracket to line up with the two rightmost holes in the
G1000 Avionics Panel as shown below and use the remaining M4x12mm screws, washers, and nuts to secure
the avionics panel to the avionics table uniformly along the front lip. Use the universal wrench to prevent the
nuts from turning while tightening.

PAGE
7
STEP 4: Attach the two (2) rear support brackets as shown below by loosening two (2) nuts underneath the
Avionics Panel glare-shield. Ensure that the position of the brackets will not interfere with the Yoke/Throttle
panel installation. Gently push the front of the Avionics Panel towards the back to slightly pre-load the
support brackets. When satisfied with the position, tighten the nuts under the glare shield.
OPTIONAL: Attach the Logitech/Saitek Pro Flight instruments into the cutouts provided in the Avionics
Panel using provided M4x30mm screws and the included M4 nuts.
Mounting a tablet (e.g. iPad) can be done using dual-sided 3M tape or couple strips of Velcro while routing
iPad’s charging table behind it or using AMPS STANDARD (38mmx30mm) ball mount drill pattern and space
for attaching a tablet (e.g. iPad or iPad mini). Note: Ball mount is not provided. Example of suitable ball
mount include RAM-B-347U RAM Mounts Ball Adapter with AMPS Plate with B Size 1" Ball.
See Appendix A and B for tips on attaching Honeycomb Alpha yoke and Bravo throttle. Use the provided
rectangular blanking plates to cover-up unused openings.
See Appendix C for instructions on installing Seat Riser Kit to raise Volair Sim Chassis seat height.

PAGE
8
APPENDIX A – HONEYCOMB ALPHA FLIGHT YOKE INSTALLATION
There are two options for installing the Honeycomb Alpha Flight Yoke:
OPTION – 1 (PREFERRED)
Remove the decorative trim from the yoke as shown in STEP 1 below. Next, Attach the Alpha yoke to the
Avionics Table using strips of dual-sided 3M tape (e.g. 3” wide). The tape strips should be mostly positioned
on the bottom back and sides of the yoke and/or throttle as the front of the yoke/throttle will be held by the
front of the avionics panel. Once the yoke/throttle is affixed to the avionics table, the avionics panel can be
installed from the front with no interference between the avionics panel and the yoke/throttle face.
Note: The yoke face will follow the outline of the face of the Avionics Panel and the distance from the
edge of the end of the avionics table will be approx. 2”.

PAGE
9
OPTION 2
If desired, the Honeycomb yoke and/or throttle can also be
installed with the Honeycomb micro-suction mounting
plate using the following steps:
STEP 1 – Remove the yoke decorative trim from the top of
the Honeycomb yoke by unscrewing four (4) hex screws as
shown:
STEP 2– Install the Honeycomb micro suction mounting
plate on the Volair Sim avionics table. The front of the
plate must be positioned behind the two holes drilled on
the front of the avionics table as circled in red.
STEP 3– Attach the Honeycomb yoke on top of the mounting plate and slide the Avionics Panel from the
front. Lastly, attach the panel to the avionics table with provided hardware.
NOTE: WHEN USING THE MICRO-SUCTION METHOD, THE YOKE FACE WILL BE POSITIONED BEHIND
THE FACE OF THE AVIONICS PANEL.