Volair Sim VS-MS User manual

©"2017"BARELLE"GROUP"LLC."ALL"RIGHTS"RESERVED.!
!
www.volairsim.com
Triple Display Stand Assembly Instructions
P/N: VS-MS
Version 1.1

Page!2!of!9!
Thank you for your purchase of the Volair SimTM Triple Display stand! We hope that it will give you
countless hours of enjoyment. We designed the stand with maximum ease of assembly but please
read these instructions carefully first.
TV | MONITOR SIZE SUPPORTED
27”- 46” DIAGONAL
VESA PATTERNS SUPPORTED
100mmx100mm
200mm(H)x100mm(V)
200mmx200mm
400mmx400mm (using the included adapters)
VOLAIR SIM TRIPLE DISPLAY STAND SPECIFICATIONS
Your Volair Sim Triple Display Stand is shipped in one large box. We recommend that you find an
open space to carefully unpack and inventory everything before beginning the assembly process.
Please refer to TABLE 1 to verify that you have all of your hardware.
NOTE: SOME PARTS MAY BE PRE-INSTALLED ON THE TRIPLE DISPLAY STAND.

Page!3!of!9!
NO.
PART NAME
QTY PHOTO COMMENTS
1
M8*20mm Socket Cap
Machine Screw
4
USED TO SECURE HORIZONTAL SUPPORT TO THE
VERTICAL POSTS - PACKED IN HARDWARE BAG
2
M8*20mm Machine Screw
with Knob
6
PACKED IN HARDWARE BAG
3
M6*12mm Button Head
Machine Screw
30
INCLUDES 12 EXTRA SCREWS FOR ATTACHING 3
TVs - PACKED IN HARDWARE BAG
4
M6*12mm Button Head
Machine Screw
16
PRE-INSTALLED
5
M6 Nut
18
USED TO ATTACH THE 400mmx400mm
EXTENSIONS - PACKED IN HARDWARE BAG
6
M8 Handle Nut
3 PACKED IN HARDWARE BAG
7
M8 Cap Nut
16 PRE-INSTALLED
8
M8 Flat Washer
16 PRE-INSTALLED
9
Hex Key M6
1
FOR M6*12mm Button Head Machine Screw - PACKED
IN HARDWARE BAG
10 Hex Key M8 1
FOR M8*20mm Socket Cap Machine Screw - PACKED
IN HARDWARE BAG
TABLE 1: Triple Display Stand Parts List

Page!4!of!9!
STEP1: Begin assembly by attaching left and right leg extensions to stand base. Use four M8x20mm
Machine Screws with Knobs (#2 in TABLE 1) to secure the four leg extensions to base as shown
below in FIGURE 1 below. HINT: The legs extensions can be positioned facing inward (for minimizing
footprint) or outward (for maximizing stability when large TVs are used). The amount of in/out
positioning of the extensions depends on the size/weight of your TVs/monitors and you will adjust
them after you have mounted your TVs in STEP 6.
FIGURE 1
x!

Page!5!of!9!
STEP 2: Attach the horizontal support to the left and right legs using four M8x20mm Socket Cap
Machine Screws (#1 in TABLE 1) as shown on FIGURE 2 below. Use the Hex Key (#10 in TABLE 1) to
tighten the four cap screws.
FIGURE 2
STEP 3: Slide the completed assembly from STEP 3 into the left and right base legs (a helper here is
desired). Use two M8x20mm Machine Screws with Knobs (#2 in TABLE 1) to adjust the height and
level of the center assembly. Ensure that the knobs are pointing towards the back. See FIGURE 3 for
details:

Page!6!of!9!
FIGURE 3

Page!7!of!9!
STEP 4: Attach left and right arms to the center section by loosening the pre-installed M8 Cap Nuts
(#7 in TABLE 1) and M8 Washers (#8 in TABLE 1), removing the threaded silver rod, and attaching
each arm to the center section as shown in FIGURE 4 below:
FIGURE 4

Page!8!of!9!
STEP 5: Attach left, center, and right display mounting plates to the backs of your TVs or monitors
using twelve (four per TV) M6x12mm Button Head Machine Screws (#3 in TABLE 1) and the M6 hex
key (#9 in TABLE 1). Use appropriate VESA bolt pattern suitable for your TV or monitor. Do not
tighten the screws all the way since you will have to align them in STEP 6.
The TV/monitor mounting plates accommodate the following VESA bolt patterns: 100mmx100mm,
200mm(H)x100mm(V), and 200mmx200mm. If you plan on using 400mmx400mm pattern (typical in
large TVs), you must use the 400mmx400mm adapters shown in FIGURE 5 below. Use eighteen
M6x12mm button head machine screws (#3 in TABLE 1) and eighteen M6 self-locking nuts (#5 in
TABLE 1) as shown in FIGURE 5 below:
FIGURE 5 – ATTACHING 400mmx400mm EXTENSIONS

Page!9!of!9!
STEP 6: Hang the TVs/monitors on the stand starting with the center one first. Next, adjust the
angle of the left and right displays by moving the left and right arms on the pivot points. You can
adjust the horizontal position of the side displays by sliding them in and out on the side arms. When
satisfied, secure the display bracket onto the arm with the metal channel piece and the M8 Handle
Nut (Item #6 in TABLE 1) as shown in FIGURE 6 below.
The vertical position and the leveling of the displays can be adjusted by loosening the VESA mounting
screws and moving the TVs/monitors UP/DOWN in the slotted holes as shown below.
HINT: It is helpful to have a second person assist with the alignment process.
FIGURE 6
Finally, check for stability of the display stand with the TVs/monitors installed. Adjust the in/out
positioning of the base leg extensions as necessary. Enjoy your Volair Sim Triple Display Stand!