Volt VSAL-9003-BBZ User manual

VOLT®Solar Landscape Lighting
VOLT® Solar Spotlight with Motion Sensor
VSAL-9003-BBZ
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2020, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -

VOLT®Solar Spotlight with Motion Sensor
VSAL-9003-BBZ
Important: Please Read Before Installation
IMPORTANT SAFETY INSTRUCTIONS
INSTALLATION INSTRUCTIONS
!
!
www.voltlighting.com
- 2 -
This luminaire is intended for installation in accordance with local
codes and the National Electric Code (NEC). Failure to adhere to these
codes and instructions may result in serious injury, property damage
and void the warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Lamp gets HOT quickly!
2. Do not touch the hot lens, guard or enclosure.
3. Keep lamp away from materials that may burn.
4. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
5. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
Package Contents
A. (1) Fixture

[email protected] • 813.978.3700
Product Dimensions
Test Solar Light
1
- 3 -
2.5”
5.25”
6”
4.25”
11.25”
6.5”
Place the solar light on a non-
abrasive surface with the solar
panel face down. Press the ON/
OFF switch on the back of the x-
ture body. Wave your hand in front
of the sensor to test the xture.
Now you can proceed to the next
steps of installation.
Non-Abrasive Surface
Solar
Panel
1
2
3
Sensor
Push On/Off Switch

INSTALLATION INSTRUCTIONS
www.voltlighting.com
VOLT® Solar Spotlight with Motion Sensor
VSAL-9003-BBZ
Install Stake
Install Fixture Body to Stake
2
3
- 4 -
Determine the desired
location for mounting the
stake mount. Hammer the
stake into the ground until
ange of stake is ush to
grade. To avoid damage to
the stake, place a board
on top of the stake while
hammering.
Note: If the ground is hard
and the stake is difcult to
install, make a crosscut in the
ground using a at shovel.
Board
Ground
Stake
Thread the xture body on to
the stake. Hand tighten until
snug. Make sure the sensor is
facing the desired area to be
monitored during installation.
NOTE: The light will illuminate
for 15 seconds after the sensor
trips. The sensor distance is
23ft with 1200 detection angle.
Fixture Body
Ground
Soil
Stake
Sensor

[email protected] • 813.978.3700
Adjust Solar Panel Direction
5
Adjust Luminaire Direction
4
- 5 -
Adjust the sensor by using the
lock screw.
Adjust the luminaire angle by
using the knuckle.
Luminaire
Knuckle
Lock Screw
1
2
2
Solar Panel
Adjust the solar panel piece
forward and backwards by using
the hand screw.
You can also take the solar pan-
el piece itself and rotate it in
any direction you need to face
the sun.
Hand Screw
1

www.voltlighting.com
- 6 -
Replace Sensor
If necessary, remove the cover to
replace the sensor. Always install the
cover back to protect the sensor.
Sensor
INSTALLATION INSTRUCTIONS
VOLT® Solar Spotlight with Motion Sensor
VSAL-9003-BBZ

[email protected] • 813.978.3700
- 7 -

is-vsal-9003-BBZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2020, VOLT® Lighting, Lutz FL USA 33549 • All rights
reserved. [email protected] • 813.978.3700
www.voltlighting.com
- 8 -