Voltronic Power SCC-MPPT 300W User manual

SCC-MPPT
Solar Charge Controller
Quick Guide
SCC-MPPT 300W SCC-MPPT 600W
Table 3: Charging voltage for 4 types of battery
Battery
Type
Battery
Type
Code
12V battery system
24V battery system
Bulk
Voltage
Floating
Voltage
Bulk Voltage
Floating
Voltage
Vented
01
14.3 V
13.2 V
28.6 V
26.4 V
Sealed
02
14.3 V
13.4 V
28.6 V
26.8 V
Gel
03
14.3 V
13.7 V
28.6 V
27.4 V
NiCd
04
14.3 V
14.0 V
28.6 V
28.0 V
Custom
05
Self-defined
Self-defined
Self-defined
Self-defined
Table 4: Alarm point for low battery voltage table
Connected battery system
Alarm point
12V
10.5 V
24V
21.0 V
Table 5: Charging hour table for reference
Battery Capacity
To 90% capacity @ 25A charging current
52 Ah
2 hours
100 Ah
4 hours
200 Ah
8 hours
300 Ah
12 hours
400 Ah
16 hours
500 Ah
20 hours
Table 6: Power consumption of home appliances table*
Appliances
Power
Consumption (W)
Daily usage hours
Daily watt hours
used (Wh)
Lighting bulb
60
6
360
Energy saving
bulb
13 6 78
Electric fan
60
12
720
TV
100
4
400
Washing
machine
800 1 800
Air conditioner
800
6
4800
Freezer
400
24
9600
PC with 17”
monitor
150 6 900
Laptop
70
6
420
*This power consumption table may be different based on different consumer
behavior and local electronic specifications. V. 2.1
11

1. Introduction
SCC-MPPT solar charge controller uses PWM-based DSP controller to keep the
batteries regulated and prevent batteries from overcharging and discharging.
Applying intelligent MPPT algorithm, it allows SCC-MPPT solar charge controller to
extract maximum power from solar arrays by finding the maximum power point of
the array.
The solar charge controller facilitates a standalone energy system. Typical
applications are listed below:
Mobile applications such as moving van, lodge, log cabin, or night market.
Lighting applications such as street lights, road lights, or garage lights.
Remote village with power shortage
1. Product Overview
Power switch
Solar energy status indicator (Blue LED)
Charging status indicator (Green LED)
Site wiring fault indicator (Red/Orange/Yellow LED)
LCD display (see Operation Section for the details)
Terminal block for solar panel connection
Terminal block for battery connection
Terminal block for load connection
2. Installation
Inspection
Remove the unit from the shipping package and inspect it for damage that may
occur during transportation. Notify the carrier and place of purchase if any damage
is found.
Installation Note
Read all the installation section before beginning installation
CAUTION! Careful to reduce the risk or dropping a metal tool on the batteries. It could
spark or short circuit the batteries and could cause an explosion.
CAUTION! Remove personal metal items such as rings, bracelets, necklaces, and
watches when working with batteries. Batteries can produce a short circuit current high
enough to make metal melt, and could cause severe burns.
CAUTION! Avoid touching eyes while working near batteries.
CAUTION! Have plenty of fresh water and soap nearby in case battery acid contacts
skin, clothing, or eyes.
Explosive battery gasses may be present during charging . be certain there is sufficient
ventilation to release the gasses.
CAUTION! NEVER smoke or allow a spark or flame in vicinity of a battery.
Do not expose this charger controller to rain, snow or liquids of any type.
WARNING! Provide ventilation to outdoors from the battery compartment. The battery
enclosure should be designed to prevent accumulation and concentration of hydrogen
gas at the top of the compartment.
CAUTION! Use insulated tools to reduce the chance of short-circuit when installing or
working with the inverter, the batteries, or other equipments attached to this unit.
CAUTION! For battery installation and maintenance, read the battery manufacturer's
installation and maintenance instructions prior to operating.
Only charge Sealed Lead Acid, Vented Lead, NiCd or Gel batteries.
CAUTION! To reduce risk of injury, only use qualified batteries from qualified
distributors or manufacturers. Any unqualified batteries may cause damage and injury.
Do NOT use old or overdue batteries. Please check the battery type and date code
before installation to avoid damage and injury.
WARNING! It's very important for safety and efficient operation to use appropriate
external battery cable. To reduce risk of injury, external cables including battery cables,
PV panel cables and load connected cables should be UL certified and rated for 75° C or
higher. And strongly suggest not to use copper cables less than 12AWG. Below is the
external battery cable reference according to system requirements.
Model
Nominal Battery Voltage
Typical Current (Amp)
SCC-MPPT 300W
12 V
25 A
SCC-MPPT 600W
12V or 24 V (auto sensing)
25 A
NOTE: It's recommended to allow experienced personnel to install solar panel
because the efficiency of solar energy transmission is directly effected by
installation angles. Please follow the voltage requirement of the unit to wire
connection with solar panel and batteries.
1 2

Terminal Installation
Step 1: Prepare flat screwdriver, supplied terminals and
stripped wires.
Step 2: Insert stripped wire into supplied terminal.
Use crimping tool to press stripped wire and terminal
in position. Refer to chart2.
Step 3: Screw assembled terminal and wire into solar
charge controller. Refer to chart 3.
Chart 3
Mounting
Step 1: Choose mounting location
Locate the solar charger controller on a vertical surface. Select an appropriate
mounting location. Use a horizontal line and the length of the line must be 150mm
and mark the two ends on the wall. (see Fig. 1 & Fig. 3)
Step 2: Check the clearance
Install the solar charge controller in a protected area that is free of excessive dust
and has adequate air flow. Please place the solar charge controller away from other
units at least 20 cm to avoid interference. Do NOT operate it where the temperature
and humidity is outside the specific limits. (Please check the specs for the
limitations.)
Step 3: Drill the holes
Remove the controller and drill 2 holes in the marked locations with 2 screws.
Step 4: Secure controller
Place the unit on the surface and align the mounting holes with 2 screws in step 3.
(see Fig. 2 & Fig. 4)
Fig. 1 Fig. 2
Fig. 3 Fig. 4
Wiring
CAUTION! Be sure to secure all wiring, especially for mobile applications. Use
cable clamps to prevent cables from swaying when the vehicle is in motion.
Unsecured cables create loose and resistive connections which may cause excessive
heating or fire
Step 1: DC Load Wiring
The load output will provide battery voltage to connected loads such as lights,
pumps, monitors and other electronic devices.
Step 1: connect load positive (+) wire to the positive terminal of the unit and load
negative (-) wire to the negative terminal of the unit.
Step 2: install a DC Breaker or a DC fuse holder in a positive wire. The rating of the
DC Breaker/Fuse must be according to the charging current (40 Amp). Keep the DC
Wall
Chart 1
Chart 2
3 4

breaker off or do not install the DC fuse.
WARNING! Please use the appropriate cable size according to load rating. Please
refer to Important Safety Warnings Section for the details. It will prevent internal
high temperature.
Step 2: Battery Wiring
Step 1: connect battery positive (+) wire to the positive terminal of the unit and
load negative (-) wire to the negative terminal of the unit.
Step 2: install a DC Breaker or a DC fuse holder in a positive wire. The rating of the
DC Breaker/Fuse must be according to the charging current (40 Amp). Keep the
DC breaker off or do not install the DC fuse.
1) Multiple batteries in series connection (Refer to Fig. 5): All batteries
must be equal in voltage and amp hour capacity. The sum of their voltages
must be equal to the nominal DC Voltage of the unit.
Fig. 5
2) Multiple batteries in parallel connection (Refer to Fig. 6): Each battery's
voltage must be equal to the Nominal DC Voltage of the unit.
Fig. 6
Step 3: Solar Module Wiring
WARNING: Risk of electric shock! Exercise caution when handing solar wiring. The
solar array high voltage output can cause severe shock or injury. Cover modules
from the sun before installing solar panel wiring.
Step 1: connect positive (+) wire of solar module to the positive terminal of the
unit and negative (-) wire of solar module to the negative terminal of the unit.
1) Single solar module connection (Refer to Fig. 7): When using a single
solar module, its voltage must not exceed the maximum solar module open
circuit voltage (see below Table 1).
Fig. 7
Table 1:
Model
Solar Module Open Circuit
Voltage (max.)
Maximum Solar Module
Power
SCC-MPPT 300W
50 VDC
300 W
SCC-MPPT 600W
75 VDC@ 24 V or 50 VDC@ 12 V
600 W@24V or 300 W@12V
2) Multiple solar modules in series connection (Refer to Fig. 8): All
modules must be equal in voltage and amp hour capacity. The sum of their
voltages must not exceed the maximum solar module open circuit voltage. And,
the sum of their solar power must not exceed the maximum capacity of the
unit.
Fig. 8
3) Multiple solar modules in parallel connection (Refer to Fig. 9): Each
module's voltage must not exceed the maximum solar module open circuit
voltage. And, the sum of their solar power must not exceed the maximum
capacity of the unit.
5 6

Fig. 9
CAUTION: It may not cause any damage to solar module or unit when connecting
polarity reversals. However, the unit will not be able to work normally.
WARNING! Please use the appropriate cable. Please refer to Important Safety
Warnings Section for the details.
Step 4: Switch on DC breaker or install DC fuse
After completing all wires, double check if all wires are connected well. Then switch
on DC breaker or install DC fuse on. Take off the cover of solar module. When the
voltage of solar module is 5VDC higher than battery voltage, the charger will
automatically turn on to work.
NOTE: If battery is not connected, even though solar module power is achieved,
the charger is still not working.
3. Operation
After all wires are connected, the solar charge controller will automatically be
activated. At this time, the blue LED will light up and LCD display panel will show
information.
Switch Operation
The switch has three modes during operation:
Activate LCD backlight
Press button for less than 1 second
Select battery type*
When the unit starts to work, press button for 1-3
seconds to select battery type.
DI: vented battery
D2: sealed lead acid battery
D3: Gel battery
D4: NiCd battery
D5
: Custom**
Mute
Press button > 3 seconds
Power on
Press button for 1 second to turn on the unit.
*Please carefully to select battery type. It will damage battery if the setting is
incorrect. Refer to charging voltage table in the appendix.
**This option is self-defined bulk/floating voltage via bundled software.
Status, LED/LCD Display and Audible Alarms
Status
LCD
LED
Alarm
Polarity reversal on
solar module
connection.
N/A Yellow LED on. N/A
Polarity reversal on
battery connection.
N/A Red LED on. N/A
Polarity reversal on
battery and solar
module connection.
N/A Orange LED
on. N/A
Battery is in
charging.
Blue & Green
LEDs on.
N/A.
Low battery
voltage.*
Flashing every
sec.
N/A Sounding every sec
110% overload.
Flashing
every 2 secs.
N/A Sounding every 2 secs. for 5 min. Then
continuously sounding.
*Refer to alarm point for low voltage table in appendix.
Fault and error codes table:
Status
LCD
LED
Alarm
Battery defect. There is power
input from solar module, but
battery voltage is too low.
12V system: < 8.5V
24V system: < 17V
Green LED
on. Continuously sounding.
Overcharge and the charger will
automatically cut off output.
Blue LED on
Continuously
sounding.
130% overload and the charger
will automatically cut off output.
N/A
Continuously
sounding.
When solar input voltage is too
high, the charger will
automatically cut off charging.
Blue LED
flashes every
second
N/A
7 8

4. Specifications
Model
SCC-MPPT 300W
SCC-MPPT 600W
INPUT
MPPT Range @ Operating
Voltage
15 V ~ 37 V @ 12 V
30 V ~ 66 V @ 24 V
15 V ~ 33 V @ 12 V
Maximum Solar Module Open
Circuit Voltage
50 V
75 V@ 24 V
50 V@ 12 V
Maximum Solar Module Power
300 W
600W@24V
300W@12V
Maximum Current
18 A
18 A
OUTPUT
Nominal Battery Voltage
12V
24V or 12V (auto sensing)
Connected Battery Type
Sealed lead acid, vented, Gel, NiCd battery
Maximum Charging Current
25 A
25 A
Standby Power Consumption
2 W
Charging Method
Three stages: bulk, absorption, and floating
PHYSICAL
Dimension (DxWxH mm)
135 x 170 x 57.5
220 x 170 x 57.5
Net Weight (kgs)
0.92
1.85
ENVIRONMENT
Humidity
0-100 % RH (non-condensing)
Operating Temperature
-20
°
C - 55
°
C
Storage Temperature
-40
°
C - 75
°
C
5. Trouble Shooting
Problem
Possible Cause
Solutions
Yellow LED on
Polarity reversal on solar
module connection.
Reconnect polarity again
Red LED on.
Polarity reversal on
battery connection.
Reconnect polarity again.
Orange LED on.
Polarity reversal on solar
module and battery
connection.
Reconnect polarity of
solar module and battery
again.
No solar energy input
during daytime.
Wires are not firmly
connected.
Check if all wires are
connected properly.
Solar module defect.
Check solar modules or
call local dealer to
replace solar modules.
F0 fault code displays
on LCD panel
Battery wires are not
connected well.
Check if battery wires
are properly connected.
Battery defect.
Replace battery.
Backup time is shorter.
Battery defect.
Check battery life cycle
and replace battery.
Overload.
Remove excess loads.
Problem
Possible Cause
Solutions
F1 fault code displays on
LCD panel.
Battery wires are not
connected well.
Check if battery wires
are properly connected.
Battery defect.
Replace battery.
Charge controller defect.
Replace the unit.
F2 fault code displays on
LCD panel.
Overload.
Remove excess loads.
E1 fault code displays on
LCD panel.
Solar input voltage is too
high.
Check if solar wiring is
correct. And then check
solar input voltage.
If there is any abnormal situations occur which doesn't list above, please call the
service people immediately for professional examine.
APPENDIX
Table 1: Recommended minimum battery cable size versus length
Model
Nominal battery
Voltage
Charging
Current
1 meter
(one-way)
Dia-mm
SCC-MPPT 300W
12 V
25 A
AWG 12
2.0525
SCC-MPPT600W
24 V or 12 V
(auto sensing)
25 A
AWG 12
2.0525
Table 2 External Battery Cable Size Reference
AWG
(American Wire Gauge Size)
Dia-mm
(Diameter in millimeters)
Ohms/Kft (Ohms per 1,000ft
or 304.8 meter)
0000(4/0)
11.684
0.049
000(3/0)
10.405
0.0618
00(2/0)
9.2657
0.0779
0(1/0)
8.2513
0.0983
1
7.348
0.1239
2
6.5436
0.1563
3
5.8272
0.197
4
5.1893
0.2485
5
4.6212
0.3133
6
4.1153
0.3951
7
3.6648
0.4982
8
3.2636
0.6282
9
2.9063
0.7921
10
2.5881
0.9989
11
2.3048
1.2596
12
2.0525
1.5883
9 10